Difference between revisions of "Join and Reset Instructions"

From Hubitat Documentation
Jump to: navigation, search
(Added joining and exclusion pre-requisites)
(Added Kwikset 910 Z-Wave and Zigbee)
Line 1: Line 1:
−
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into '''Paring Mode''' using the manufacturer's instructions, Z-Wave devices must be '''Excluded''' from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a '''General Exclusion''' in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. If Hubitat doesn't show '''Unknown Device Excluded''' in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
+
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into '''Paring Mode''' using the manufacturer's instructions, Z-Wave devices must be '''Excluded''' from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a '''General Exclusion''' in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show '''Unknown Device Excluded''' in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
  
 
===Schlage BE469 Lock===
 
===Schlage BE469 Lock===
 
'''Factory Reset'''
 
'''Factory Reset'''
  
−
#Disconnect the batteries.
+
#Disconnect the batteries
−
#Press and hold the Outside Schlage Button.
+
#Press and hold the outside Schlage button
−
#While holding the Outside Schlage Button, then reconnect the batteries.
+
#While holding the outside Schlage button, then reconnect the batteries.
 
#Release the Outside Schlage Button. '''NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.'''
 
#Release the Outside Schlage Button. '''NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.'''
−
#To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User Codes.
+
#To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
 
#If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.
 
#If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
−
#From the Hubitat Web Interface home page, select "Z-Wave", then "Start Z-Wave Pairing" on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Schlage button
 
#Press the Schlage button
Line 29: Line 29:
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
  
−
#From the Hubitat Web Interface home page, select "Z-Wave", then "Start Z-Wave Exclusion" on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Schlage button
 
#Press the Schlage button
 
#Enter the 6 digit programming code
 
#Enter the 6 digit programming code
 
#Press 0
 
#Press 0
−
#A '''√''' indicates the lock was successfully excluded the Z-Wave network, while an '''X''' indicates that it did not successfully leave the networ
+
#A '''√''' indicates the lock was successfully excluded the Z-Wave network, while an '''X''' indicates that it did not successfully leave the network
 +
 
 +
===Kwikset 910 Z-Wave Lock===
 +
'''Factory Reset'''
 +
 
 +
#Remove battery pack
 +
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
 +
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
 +
#Perform the '''door handing''' process again.
 +
#*Press and hold the Lock button while installing battery pack.
 +
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 +
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
 +
 
 +
'''Join the Z-Wave Network'''
 +
 
 +
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
 +
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.
 +
 
 +
'''Exclusion from the Z-Wave Network'''
 +
 
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
 +
 
 +
===Kwikset 910 Zigbee Lock===
 +
'''Factory Reset'''
 +
 
 +
#Remove battery pack
 +
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
 +
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
 +
#Perform the '''door handing''' process again.
 +
#*Press and hold the Lock button while installing battery pack.
 +
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 +
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
 +
 
 +
'''Join the Zigbee Network'''
 +
 
 +
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock '''4 times''' to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
 +
#*If pairing is unsuccessful ZigBee Inclusion: Press button '''B''' on the lock '''9 times'''. Repeat the pairing process.
 +
 
 +
'''Leaving the Zigbee Network'''
 +
 
 +
#From the device's details page, click '''Remove Device''', then '''Remove'''
 +
#Press button '''B''' on the lock '''9 times'''.
  
 
===GE Outdoor Switch===
 
===GE Outdoor Switch===
Line 44: Line 95:
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
−
#From the Hubitat Web Interface home page, select "Z-Wave", then "Start Z-Wave Pairing" on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the manual/program button once
 
#Press the manual/program button once
Line 50: Line 101:
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
  
−
#From the device's details page, click "Remove Device", then "Remove"
+
#From the device's details page, click '''Remove Device''', then '''Remove'''
 
#Press the manual/program button on the switch once
 
#Press the manual/program button on the switch once
 +
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
  
 
__FORCETOC__
 
__FORCETOC__

Revision as of 21:25, 1 May 2019

Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See How to Build a Solid Z-Wave Mesh for further detail on methods of Exclusion.

Schlage BE469 Lock

Factory Reset

  1. Disconnect the batteries
  2. Press and hold the outside Schlage button
  3. While holding the outside Schlage button, then reconnect the batteries.
  4. Release the Outside Schlage Button. NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.
  5. To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
  6. If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Schlage button
  3. Enter the 6 digit programming code
  4. Press 0
  5. A √ indicates the lock successfully joined the Z-Wave network, while an X indicates that it did not successfully join the network

Verify Z-Wave connection status from the lock

  1. Remove the battery cover
  2. Disconnect the battery connector
  3. While watching the inside Schlage button, reconnect the battery connector
  4. The inside Schlage button will blink if the lock is enrolled

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press the Schlage button
  3. Enter the 6 digit programming code
  4. Press 0
  5. A √ indicates the lock was successfully excluded the Z-Wave network, while an X indicates that it did not successfully leave the network

Kwikset 910 Z-Wave Lock

Factory Reset

  1. Remove battery pack
  2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
  3. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
  4. Perform the door handing process again.
    • Press and hold the Lock button while installing battery pack.
    • Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
    • If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.

Join the Z-Wave Network

  1. Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press button A on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
  4. If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  5. Press button A on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press button A on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.

Kwikset 910 Zigbee Lock

Factory Reset

  1. Remove battery pack
  2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
  3. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
  4. Perform the door handing process again.
    • Press and hold the Lock button while installing battery pack.
    • Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
    • If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.

Join the Zigbee Network

  1. Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Press button A on the lock 4 times to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
    • If pairing is unsuccessful ZigBee Inclusion: Press button B on the lock 9 times. Repeat the pairing process.

Leaving the Zigbee Network

  1. From the device's details page, click Remove Device, then Remove
  2. Press button B on the lock 9 times.

GE Outdoor Switch

Factory Reset

  1. Unplug switch from outlet
  2. Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the manual/program button once

Exclusion from the Z-Wave Network

  1. From the device's details page, click Remove Device, then Remove
  2. Press the manual/program button on the switch once
    • Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.


Retrieved from "https://docs.hubitat.com/index.php?title=Join_and_Reset_Instructions&oldid=1886"