Difference between revisions of "Join and Reset Instructions"
(Added Remotec ZFM-80 and ZRC-90) (Tag: Visual edit) |
(Added Salus SP-600 smart plug) (Tag: Visual edit) |
||
Line 7,491: | Line 7,491: | ||
#If the LED flashes '''6 times''' rapidly, then remains off, the device has faililed to be excluded in the Z-Wave network. | #If the LED flashes '''6 times''' rapidly, then remains off, the device has faililed to be excluded in the Z-Wave network. | ||
#Peform a factory reset and repeat the above steps to exclude the device from the Z-Wave network. | #Peform a factory reset and repeat the above steps to exclude the device from the Z-Wave network. | ||
+ | |||
+ | <hr /> | ||
+ | =='''<big>Salus</big>'''== | ||
+ | {| class="wikitable sortable" | ||
+ | |<div style="text-align: center;">Brand</div> | ||
+ | |<div style="text-align: center;">Device</div> | ||
+ | |<div style="text-align: center;">Product Number</div> | ||
+ | |<div style="text-align: center;">Device Type</div> | ||
+ | |<div style="text-align: center;">Protocol</div> | ||
+ | |- | ||
+ | |<div style="text-align: center;">'''<big>Salus</big>'''</div> | ||
+ | |<div style="text-align: center;">'''<big>Smart Plug</big>'''</div> | ||
+ | |<div style="text-align: center;">'''<big>SP-600</big>'''</div> | ||
+ | |<div style="text-align: center;">'''<big>Outlet</big>'''</div> | ||
+ | |<div style="text-align: center;">'''<big>Zigbee</big>'''</div> | ||
+ | |} | ||
+ | '''Factory Reset''' | ||
+ | |||
+ | #Press the button on the outlet for 10 seconds. | ||
+ | #The light surrounding the button will flash '''RED''' ''5 times'', and will then go out. | ||
+ | |||
+ | '''Join the Zigbee Network''' | ||
+ | |||
+ | #From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery. | ||
+ | #*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions. | ||
+ | #Press the button on the outlet for 10 seconds. | ||
+ | #The light surrounding the button will flash '''RED''' ''5 times'', and will then go out. | ||
+ | #If the device is not discovered by Hubitat Elevation™, then unplug the outlet for 10 seconds and plug it in again. It should now be discovered by the hub. | ||
+ | |||
+ | '''Leaving the Zigbee Network''' | ||
+ | |||
+ | #From the device's details page, select '''Remove Device''', then '''Remove.''' | ||
+ | #Press the button on the outlet for 10 seconds. | ||
+ | #The light surrounding the button will flash '''RED''' ''5 times'', and will then go out. | ||
<hr /> | <hr /> |
Revision as of 17:45, 5 September 2019
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See How to Build a Solid Z-Wave Mesh for further detail on methods of Exclusion.
Contents
- 1 ADT
- 2 AduroSmart
- 3 Aeotec (Aeon Labs)
- 4 August
- 5 BeSense
- 6 Centralite
- 7 CREE
- 8 Dome
- 9 Dragon Tech
- 10 Eaton (Cooper Wiring Devices)
- 11 Ecolink
- 12 Enerwave
- 13 Everspring
- 14 Evolve
- 15 Fibaro
- 16 First Alert
- 17 GE/Jasco
- 18 GoControl
- 19 Graber
- 20 Halo Labs
- 21 Hampton Bay
- 22 Hank
- 23 HomePro
- 24 Homeseer
- 25 IKEA
- 26 Inovelli
- 27 IRIS
- 28 KEEN Home
- 29 Kwikset
- 30 Leak Intelligence
- 31 Leviton
- 32 Linear
- 33 Lutron
- 34 LUX
- 35 MCO Home
- 36 Monoprice
- 37 Neo
- 38 NodOn
- 39 NYCE
- 40 Orbit
- 41 Orvibo
- 42 OSRAM
- 43 Philips Hue
- 44 Qubino
- 45 Remotec
- 46 Salus
- 47 Radio Thermostat Company of America
- 48 Schlage
- 49 Utilitech
ADT
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
ADT (Nortek)
|
Water Leak Detector
|
10016864C
|
Water Sensor
|
Zigbee
|
Factory Reset
- Remove the cover by rotating it counterclockwise
- Press and hold the Connect button for 5 seconds
- After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
Join the Zigbee Network
- Remove the cover by rotating it counterclockwise
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Press and hold the Connect button for 5 seconds
- After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
AduroSmart
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
AduroSmart
|
Door / Window Sensor
|
ERIA 81822
|
Contact Sensor
|
Zigbee
|
Factory Reset
- Use the provided pin to press and hold the reset button for 10 seconds.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Use the provided pin to press and hold the reset button for 10 seconds.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
AduroSmart
|
Dimmer Switch
|
ERIA 81825
|
Button Controller
|
Zigbee
|
Factory Reset
- Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Hold down the off (circle) button for 10 seconds until it blinks green 3 times.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
AduroSmart
|
Motion Sensor
|
ERIA 81823
|
Motion Sensor
|
Zigbee
|
Factory Reset
- Use the provided pin to press and hold the reset button for 10 seconds.
- Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Use the provided pin to press and hold the reset button for 10 seconds.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Aeotec (Aeon Labs)
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Doorbell Gen5
|
ZW056
|
Doorbell
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and then release it.
- Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking as a confirmation.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Doorbell Gen5, and its LED will blink rapidly to indicate that it is communicating.
- If your Doorbell has been successfully linked to your network, its LED will become solid for 2 seconds, then stop. If linking was unsuccessful, the LED will blink when you tap its button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Doorbell.
- If your Doorbell has been successfully unlinked to your network, its LED will begin to blink slowly indicating it is ready to be paired to a new network..
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Door/Window Sensor 6
|
ZW112
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press and hold Door Window Sensor 6 Action button
- Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
- If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the button on the Door Window Sensor 6
- The LED will blink green to indicate successful inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor.
- If your Door Window Sensor is successfully removed from the Z-Wave network, the RGB LED will become a colorful gradient for a few seconds and then turn off. If the removing was unsuccessful, the RGB LED will be solid for 8 seconds and then turn off, repeat the above steps.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Door/Window Sensor Gen5
|
ZW120
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once to include the door/window sensor.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor.
- If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast blink for 8 seconds and then slow blink for 3 seconds when you press the Action Button again.
- If the removal was unsuccessful, the Status LED will fast blink for 2 seconds and then be solid for 2 seconds when you press the Action Button, repeat the above steps.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Door/Window Sensor Gen2
|
DSB29
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once to include the door/window sensor.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor to exclude it from the network
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Door/Window Sensor 1E
|
DSB04100
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Use an Aeon Z-Stick or Minimote to return the sensor to a default state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
- The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the will be blinking while awake.
- Note: The DSB04100 sensor can only be taught to communicate to devices within it’s own network.
- If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
- If the sensor was successfully included in the Z-Wave network, the LED will blink instead of staying solid.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Use an Aeon Z-Stick or Minimote to exclude the sensor from previous networks
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Garage Door Controller Gen5
|
ZW062
|
Garage Door Opener
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and release.
- Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking to confirm a success.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on the Garage Door Controller.
- The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on the Garage Door Controller.
- The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful exclusion.
- The Network LED on the Garage Door Controller should now be blinking slowly to indicate it is ready to be paired to a new network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Dry Contact Sensor Gen5
|
ZW097
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor.
- If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear. If linking was unsuccessful, the LED will continue to blink if you tap its button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor.
- If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Aeon Labs Home Energy Meter
|
AEDSB09104ZWUS
|
Energy Meter
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 10 seconds.
- If successful, the LED on the HEM should begin to blink slowly.
Join the Z-Wave Network
- Remove the screw from the back of your Reader and open the battery cover.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for 1 second. If the linking was unsuccessful the light will blink after pressing your meter’s Action Button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- Remove the screw from the back of your Reader and open the battery cover.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button (small black button under the battery tray) on your reader.If your Reader has been successfully removed from your network its light will blink for 1 second. If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Home Energy Meter Gen2 / Gen5
|
ZW095
|
Energy Meter
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 10 seconds.
- If successful, the LED on the HEM should begin to blink slowly.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your HEM. If it has been successfully linked to your network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to blink.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your HEM. If it has been successfully removed from your network, its LED will blink. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
LED Bulb Gen5
|
ZW098
|
Bulb
|
Z-Wave
|
Factory Reset
- Removing LED Bulb from your Z-Wave network will reset LED Bulb to default factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- With LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch ON. LED Bulb’s green LED will blink to indicate that it is looking for a Z-Wave network to connect to.
- After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Turn LED Bulb’s wall switch on.
- Toggle LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if successful, the orange LED will be solid for 2 seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
- To confirm successful removal its color will change to orange for 2 seconds before changing to white. If removal was unsuccessful, LED Bulb will blink orange for 3 seconds before changing to red for 2 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
LED Bulb 6 Multi-Color
|
ZWA002
|
Bulb
|
Z-Wave
|
Factory Reset
- Turn LED Bulb’s wall switch on and wait 1 second.
- Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
- If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to 10 seconds.
- After successfully connecting to your network, LED Bulb will flash green -> white color for 3 seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
- LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for 3 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
LED Bulb 6 Multi-White
|
ZWA001
|
Bulb
|
Z-Wave
|
Factory Reset
- Turn LED Bulb’s wall switch on and wait 1 second.
- Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
- If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will blink 2x times to indicate that it is looking for a Z-Wave network to connect to.
- After successfully connecting to your network, LED Bulb will blink off then on in about half a second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Turn LED Bulb’s wall switch on and wait 1 second.
- Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
- LED Bulb 6 if successful will flash once, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Micro Illuminator G2
|
DSC19103-ZWUS
|
Dimmer
|
Z-Wave
|
Factory Reset
- Hold the Z-Wave button for 30 seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for 30 seconds).
Join the Z-Wave Network
- Connect Micro Smart Dimmer to an AC‐input power source.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z‐Wave button.
- If the inclusion fails, please repeat the process from step 2.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z‐Wave button.
- If the exclusion fails, please repeat the process from step 2
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Micro Motor Controller
|
DSC14104-ZWEU/US, DSC14103-ZWAU
|
Motor Controller
|
Z-Wave
|
Factory Reset
- Use an Aeon Z-Stick or Minimote to return the controller to a default state.
Join the Z-Wave Network (Z-Stick)
- Connect Micro Motor Controller to an AC‐input power source.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Z-Stick.
- Press the Action Button on your Micro Motor Controller.
- If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
- If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
- Press the Action Button on the Z-Stick to take it out of installation mode.
Join the Z-Wave Network (Minimote)
- Connect Micro Motor Controller to an AC‐input power source.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions
- Press the Include button on your Minimote.
- Press the Action Button on your Micro Motor Controller.
- If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
- If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
- Press any button on your Minimote to take it out of inclusion mode.
Exclusion from the Z-Wave Network (Z-Stick)
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Z-Stick.
- Press the Action Button on your Micro Motor Controller.
- If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
- If the removal was unsuccessful, the Network LED will not blink.
- Press the Action Button on the Z-Stick to take it out of removal mode.
Exclusion from the Z-Wave Network (Minimote)
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Remove Button on your Minimote.
- Press the Action Button on your Micro Motor Controller.
- If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
- If the removal was unsuccessful, the Network LED will not blink.
- Press any button on your Minimote to take it out of removal mode.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Micro Switch G2
|
DSC26 / DCS18
|
Switch
|
Z-Wave
|
Factory Reset
- Press and hold the button on the Micro Switch G2 for 20 seconds and then release it.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
- If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
- If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Minimote
|
DSA03202
|
Button Controller
|
Z-Wave
|
Factory Reset
- Pull down the panel on the Minimote
- Press and hold the bottom 2 buttons down. The Red and Blue LED will alternate faster and faster.
- When both Red and Blue LED become solid, you may let go.
Include a device from the Z-Wave Network
- Tap the Inclusion (+) button, LED should be blinking blue
- Tap the button on the device you want to add
- After the LED stops flashing rapidly, tap any button to get out of inclusion mode
Exclusion a device from the Z-Wave Network
- Tap the Exclusion (-) button, LED should blink red
- Tap button on the device you want to remove
- After LED stops flashing rapidly, tap any button to get out of the exclusion mode
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Multisensor Gen5
|
ZW074
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press and hold Multisensor Gen5 Action button (For 20 seconds)
- The LED of the Multisensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
- Release the Multisensor Gen5 Action Button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on your MultiSensor.
- You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
- If the LED blinks when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on your MultiSensor.
- If your MultiSensor has been successfully removed from your network, its LED will blink when you press the Z-wave Button.
- If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Multisensor 6
|
ZW100
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
- If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
- If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your MultiSensor. The LED on Multisensor will blink Green rapidly, followed by a solid Green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
- You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
- If the green LED blinks when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
- If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
- If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
NanoMote One
|
ZWA004
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the NanoMote button for 20 seconds.
- The LED will change from: Orange > Green > Red > Pink > Red
- Release the button on the second Red LED status. It will remain red for 2 seconds
- Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Double click the NanoMote button, the LED will blink rapidly with a white color.
- If your NanoMote has been successfully added to your Z-Wave network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
- If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
- If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Double click the NanoMote button, the LED will become a solid green color.
- If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
NanoMote Quad
|
ZWA003
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the NanoMote button for 20 seconds.
- The LED will change from: Orange > Green > Red > Pink > Red
- Release the button on the second Red LED status. It will remain red for 2 seconds
- Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Double click the NanoMote button (can be any button), the LED will blink rapidly with a white color.
- If your NanoMote has been successfully added to your Z-Wave network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
- If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Double click the NanoMote button, the LED will become a solid green color.
- If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Nano Dimmer
|
ZW111
|
Dimmer
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will blink to indicate the Nano Dimmer is entering into pairing mode.
- If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
- If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Nano Switch (with energy reading)
|
ZW116
|
Switch
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once on the Nano Switch.
- If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Nano Switch (without energy reading)
|
ZW139
|
Switch
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and then release it.
- Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once on the Nano Switch.
- If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
- If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Range Extender (Aeon Labs Z-Wave Network Repeater)
|
DSD37
|
Switch
|
Z-Wave
|
Factory Reset
- Use an Aeon Z-Stick or Minimote to return the Range Extender to a default state.
Join the Z-Wave Network (Z-Stick)
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Z-Stick.
- If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
- If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
- Press the Action Button on the Z-Stick to take it out of installation mode.
Join the Z-Wave Network (Minimote)
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions
- Press the Include button on your Minimote.
- If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
- If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
- Press any button on your Minimote to take it out of inclusion mode.
Exclusion from the Z-Wave Network (Z-Stick)
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Z-Stick.
- If your Range Extender has been successfully removed from your network, its Network LED will blink.
- If the removal was unsuccessful, the Network LED will not blink.
- Press the Action Button on the Z-Stick to take it out of removal mode.
Exclusion from the Z-Wave Network (Minimote)
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Remove Button on your Minimote.
- If your Range Extender has been successfully removed from your network, its Network LED will blink.
- If the removal was unsuccessful, the Network LED will not blink.
- Press any button on your Minimote to take it out of removal mode.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Range Extender 6
|
ZW117
|
Repeater
|
Z-Wave
|
Factory Reset
- Press and hold the Z-Wave Button for 20 seconds to completely factory reset your Range Extender 6.
- During the time that you are holding your Range Extender 6 action button down, the LED will blink through these colors: Yellow (at 2 seconds) > Purple (at 5 seconds) > Red for 8 seconds (initializing factory reset) > Green for 20 seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
- You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will blink green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
- If Range Extender has been successfully added to your Z-Wave network, its LED will be solid for 2 seconds then turn off. If the adding was unsuccessful, the red LED will be on for 2 seconds and then remain colorful gradient status, repeat the steps above.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave Button on your Range Extender.
- If Range Extender has been successfully removed from your network, its RGB LED will remain colorful gradient status.
- If the removal was unsuccessful, the RGB LED will still be solid, repeat the steps above.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Recessed Door Sensor Gen5
|
ZW089
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds and then release it. Your sensor will now be reset to its original settings
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear.
- If linking was unsuccessful, the LED will continue to blink if you tap its button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time.
- If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Siren
|
ZW080
|
Siren
|
Z-Wave
|
Factory Reset
- Press and hold the Action button for 20 seconds
- At 8 seconds, the Siren will sound for 1 second, then stop
- The LED will continue to blink faster and faster and then will then turn solid for 2 seconds to indicate a successful factory reset
- You may let go of its Action button, and the Siren Gen5 factory reset is complete.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Siren Gen5, and its LED will blink rapidly to indicate that it is communicating.
- If your Siren has been successfully linked to your network, its LED will become solid for 2 seconds, then stop.
- If linking was unsuccessful, the LED will blink when you tap its button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Siren.
- If your Siren has been successfully unlinked from your network, its LED will begin to blink.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
Smart Switch 6
|
ZW096
|
Switch
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 20 seconds.
- The LED will change between these colors: Yellow > Purple > Red (blinks faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
- When the LED changes to Green state, you may let go of the action button.
- When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Switch once and the LED will flash a green LED.
- If your switch has been successfully linked to your network, its LED will become solid green for 2 seconds.
- If linking was unsuccessful, the LED will return to a rainbow gradient.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your Switch.
- If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
- If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
TriSensor
|
ZWA005
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press and hold the Action Button for 15 seconds.
- The red LED flashes to confirm a successful factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your sensor once.
- The LED will turn yellow LED for 10 seconds.
- If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your sensor.
- The LED will turn purple for 2 seconds, and then white when exclusion is successful.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
WallMote Quad
|
ZW129
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the Action button (20 seconds).
- The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
- Let go of the Action Button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once on WallMote Quad to include it.
- The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your WallMote Quad.
- If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Aeotec*
|
WallMote Quad
|
ZW130
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the Action button (20 seconds).
- The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
- Let go of the Action Button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button once on WallMote Quad to include it.
- The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Action Button on your WallMote Quad.
- If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
August
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
August
|
Smart Lock Pro
|
ASL-03
|
Lock
|
Z-Wave
|
Factory Reset
- You must have your lock first connected to the August App
- Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
- My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
- My Hub is No Longer Working - use this mode to RESET the Device.
- Select the My Hub is No Longer Working option and then select Reset Z-Wave Device.
Join the Z-Wave Network
- You must have your lock first connected to the August App
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- On the August App, go into Lock Settings and door for Z-Wave Settings.
- The first time the screen will state that "The Lock is not connected to a Z-Wave Network". Select "Add to a Z-Wave Network".
- Follow the instructions to put the lock into Learn Mode.
Exclusion from the Z-Wave Network
- You must have your lock first connected to the August App
- From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device.
- Select Remove Z-Wave Device and on the next page you will see two options.
- My Hub is in Exclusion Mode - Use this mode when you have a working hub and can properly disconnect.
- My Hub is No Longer Working - Use this mode to RESET the Device.
- Select the My Hub is in Exclusion Mode option to exclude the lock from the Z-Wave network.
BeSense
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
BeSense
|
Zwave PLUS Ceiling PIR Sensor
|
IX32
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press the tamper switch for 6 times to restore factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
Exclusion from the Z-Wave Network
- From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
BeSense
|
Zwave Plus Window/Door Sensor
|
IM20
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press the tamper switch for 6 times to restore factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
Exclusion from the Z-Wave Network
- From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
BeSense
|
Zwave PIR Sensor
|
IX30
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press the tamper switch for 6 times to restore factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
- Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
Exclusion from the Z-Wave Network
- From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
Centralite
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
Pearl Thermostat
|
3000-G
|
Thermostat
|
Zigbee
|
Factory Reset
- Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
- The device will then factory reset itself and begin looking for an open network to join.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
- The device will then factory reset itself and begin looking for an open network to join.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
3-Series Smart Outlet
|
3200-G
|
Outlet
|
Zigbee
|
Factory Reset
- Unplug any devices from the module and unplug from the wall.
- Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Unplug any devices from the module and unplug from the wall.
- Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
3-Series Door & Window Sensor
|
3300-G
|
Contact Sensor
|
Zigbee
|
Factory Reset
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
3-Series Motion Sensor
|
3305-G
|
Motion Sensor
|
Zigbee
|
Factory Reset
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
3-Series Micro Door Sensor
|
3323-G
|
Contact Sensor
|
Zigbee
|
Factory Reset
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
3-Series Micro Motion Sensor
|
3328-G
|
Motion Sensor
|
Zigbee
|
Factory Reset
- Slide the sensor off the mount, remove cover, and remove battery.
- While holding down the reset button, reinsert battery to factory reset the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Centralite
|
4-Series Smart Outlet
|
4200-C
|
Outlet
|
Zigbee
|
Factory Reset
- Unplug any devices from the module and unplug from the wall.
- Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Unplug any devices from the module and unplug from the wall.
- Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
- After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
CREE
Brand
|
Device
|
Device Type
|
Protocol
|
CREE
|
Connected LED Bulbs
|
Bulb
|
Zigbee
|
Factory Reset
- Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
- The bulb will blink once, indicating it is reset and ready for pairing
Factory Reset (Alternate Method)
- Method 1 - Use a Philips Hue Dimmer Switch
- Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
- Hold the remote within 4 inches of the bulb.
- Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts blinking on and off.
- If the bulb stopped blinking (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) blinked green - your bulb is reset.
- This method can be used for nearly ALL ZigBee LL bulbs.
- Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)
- Hold the remote within 4 inches of the bulb.
- Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
- The bulb should blink on and off
- The green LED on the remote should come on and may blink a few times.
- Continue to hold both buttons on the remote until the green LED goes off completely.
- This method can be used for nearly ALL ZigBee LL bulbs.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
- The bulb will blink once, indicating it is reset and ready for pairing
Join the Zigbee Network (Alternate Method)
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- See Factory Reset (Alternate Method) above to reset the bulb and put it into pairing mode.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Dome
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Door / Window Sensor
|
DMWD1
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Open the Cover and make sure the Door/Window Sensor is powered.
- Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the Cover of the Door/Window Sensor.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the Cover of the Door/Window Sensor.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Door / Window Sensor
|
DMDP1
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
- Wait for 5 seconds.
- Move the Magnet and Sensor Base in and out of the closed position 6 times.
- The LED indicator will light up red for five seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the Sensor Cover and the LED indicator will start blinking yellow.
- Press the Button quickly 3 times in a row.
- The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green three times then blink red until the cover is replaced.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the SENSOR COVER and the LED indicator will start blinking red.
- Press the Button quickly 3 times in a row.
- The LED Indicator will flash green three times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Leak Sensor
|
DMWS1
|
Water Sensor
|
Z-Wave
|
Factory Reset
- Open the Back Plate and make sure the Leak Sensor is powered.
- Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the cover of the Leak Sensor by twisting it apart.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the cover of the Leak Sensor by twisting it apart.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Leak Sensor
|
DMMS1
|
Water Sensor
|
Z-Wave
|
Factory Reset
- Remove the Cover and make sure the Motion Detector is powered.
- Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the cover of the Motion Detector by twisting it apart.
- Press the Connect Button quickly 3 times in a row.
- The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Mouser
|
DMMZ1
|
Mouse Trap
|
Z-Wave
|
Factory Reset
- Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press and hold the CONNECT BUTTON for at least 10 seconds then release.
- A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press the CONNECT BUTTON quickly 3 times in a row.
- The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
- Press the CONNECT BUTTON quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
On/Off Plug-In Switch
|
DMOF1
|
Switch
|
Z-Wave
|
Factory Reset
- Plug in the On/Off Plug-In Switch.
- Hold the Connect Button for 10 seconds until the LED Indicator blinks once, then release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
- Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Range Extender
|
DMEX1
|
Repeater
|
Z-Wave
|
Factory Reset
- Hold the Button for 10 seconds until the LED blinks 10 times, then release the button
Join the Z-Wave Network
- For proper inclusion, install the Range Extender in the final location where it will be used.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash 5 times indicating successful inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Button quickly 3 times in a row The LED will flash 5 times indicating successful exclusion.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Siren
|
DMS01
|
Siren
|
Z-Wave
|
Factory Reset
- Open the Back Plate and make sure the Siren is powered.
- Hold the Connect Button for 10 seconds until the LED Ring blinks once, then release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the Back Plate of the Siren.
- Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful inclusion to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the Back Plate of the Siren.
- Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful exclusion from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dome
|
Water Main Shut-Off
|
DMWV1
|
Shutoff Valve
|
Z-Wave
|
Factory Reset
- Press and hold the open/close button for at least 10 seconds then release.
- The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly 3 times in a row. The LED will stop blinking and stay on continuously upon successful inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.
Dragon Tech
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Dragon Tech
|
Plug in Z-Wave Plus Dimmer Switch
|
PD-100
|
Dimmer
|
Z-Wave
|
Factory Reset
- Unplug the PD-100 and anything the is plugged into it.
- Press and hold the button on the front of the PD-100
- Plug the PD-100 in while still pressing the button
- After 3 seconds, release the button. If the button blinks, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the button on the front of the PD-100
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the button on the front of the PD-100
Eaton (Cooper Wiring Devices)
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Eaton
|
Wireless Dimmer
|
RF9540
|
Dimmer
|
Z-Wave
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.
Join the Z-Wave Network
- Cooper Wiring Devices Z-Wave device has a blue LED, which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the device switch one time to include it in the network. The LED will stop blinking, indicating the dimmer has been successfully included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.
Ecolink
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Door / Window Sensor
|
DWZWAVE2.5-ECO
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Flood/Freeze Sensor
|
FLF-ZWAVE5
|
Water Sensor
|
Z-Wave Plus
|
Factory Reset
- The Flood Freeze sensor factory defaults on network exclusion
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for 1 second, then reinstall it.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 10 seconds, then reinstall it.
- If the LED starts blinking continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.
- If after 5 seconds the LED is not blinking, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Open the Flood Freeze case and remove the battery for 1 second.
- Replace the battery and the device should be removed from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Motion Sensor with Pet Immunity
|
PIR-ZWAVE2.5
|
Motion Sensor
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter inclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Siren
|
SC-ZWAVE5
|
Siren
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
- The LED on the front of the unit will turn off if successful exclusion from the network.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
- The LED on the front of the unit will turn off if successful included in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
- The LED on the front of the unit will turn off if successful exclusion from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
FireFighter
|
FF-ZWAVE5
|
Smoke/CO Detector
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Open the FireFighter case and press the learn button on the device for one second.
- If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Open the FireFighter case and press the learn button on the device for one second.
- If the LED starts blinking continually, the sensor has not been added. Repeat the steps.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Open the FireFighter case and press the learn button on the device for one second.
- If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Smart Switch
|
DLS-ZWAVE5
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if successful included in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Smart Switch Double Toggle
|
DTLS2-ZWAVE5
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if successful included in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Smart Switch Dual Rocker
|
DDLS2-ZWAVE5
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if successful included in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Tilt Sensor
|
TILT-ZWAVE2
|
Tilt Sensor
|
Z-Wave
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter inclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Tilt Sensor
|
TILT-ZWAVE2.5
|
Tilt Sensor
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter inclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
- Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Remove the battery for at least 5 seconds, then reinstall it.
- Re-attach the battery cover and the device with enter exclusion mode
- The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Ecolink
|
Toggle Light Switch
|
TLS-ZWAVE5
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
- The LED on the front of the unit will turn off if successful included in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion / exclusion button on the Smart Switch.
Enerwave
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Enerwave
|
Ceiling Mounted PIR Motion Sensor
|
ZWN-BPC-Plus
|
Motion Sensor
|
Z-Wave Plus
|
Factory Reset
- To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion/exclusion button on the sensor 3 times.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the inclusion/exclusion button on the sensor 3 times.
Everspring
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Everspring
|
Door/Window Detector
|
HSM02
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Press tamper switch three times within 1.5 second. The LED will be steady on.
- Within 1 second, press and hold the tamper switch until LED is off.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Everspring
|
Flood Detector
|
ST812
|
Water Sensor
|
Z-Wave
|
Factory Reset
- Press link key three times within 1.5 second. The sensor will beep each time the link key is pressed.
- Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing link key three times within 1.5 second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing link key three times within 1.5 second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Everspring
|
PIR Detector
|
HSP02
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Press tamper switch three times within 1.5 second. The LED will be steady on.
- Within 1 second, press and hold the tamper switch until LED is off.
- The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second will enter exclusion mode.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Everspring
|
Photoelectric Smoke Alarm
|
SF-813
|
Smoke Detector
|
Z-Wave
|
Factory Reset
- Press tamper switch three times within 1.5 second. The LED flashes and the buzzer sounds when the link key is pressed.
- Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
- The LED will light for 5 seconds and the buzzer will sound for 5 seconds
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
- The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
- The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has joined the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing tamper switch three times within 1.5 second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
- The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
- The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has been excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Everspring
|
Temperature/Humidity Detector
|
SF-814
|
Temperature Sensor
|
Z-Wave
|
Factory Reset
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
- Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
- When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
- When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
Evolve
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Evolve
|
Isolated Contact Fixture Module
|
LFM-20
|
Relay
|
Z-Wave
|
Factory Reset
- Factory reset is unavailable for this device. Instead, perform a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Exclude the module by tapping the button three times, then press and hold for 10 seconds.
- LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the button on the once to include it in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Exclude the module by tapping the button three times, then press and hold for 10 seconds.
- LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
Fibaro
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Button
|
FGPB-101
|
Outlet
|
Z-Wave
|
Factory Reset
- Click the Button exactly five times.
- Press and hold the Button for at least 5 seconds.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click the button at least 6 times.
- Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
- Click the button 4 times to wake it up
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click the Button at least six times.
- Wait for the removing process to end.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Door/Window Sensor 2
|
FGDW-002
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Open the cover and remove the battery.
- Install the battery while holding both TMP buttons.
- The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
- Release one button when the LED indicator starts flashing quickly.
- Click the released button once to confirm initiation of the reset procedure.
- Wait a few seconds for a long blink of the LED indicator. Do not remove the battery.
- The LED indicator will blink 5 times quickly to confirm reset of the device.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press one of the TMP buttons quickly, three times in a row, while keeping other button is pressed.
- Wait for the inclusion process to end.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press one of the TMP buttons quickly, three times in a row, while keeping other button is pressed.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Flood Sensor
|
FGFS-101 FG3
|
Water Sensor
|
Z-Wave
|
Factory Reset
- Make sure the sensor is powered.
- Press and hold the TMP button.
- Wait for the visual LED indicator to glow yellow (4th position of the MENU).
- Release the TMP button.
- Click the TMP button once to confirm selection.
- After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Removed the battery for 10 seconds, and re-install it
- Wait for the inclusion process to end.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the TMP button quickly, three times in a row.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Flood Sensor ZW5
|
FGFS-101 ZW5
|
Water Sensor
|
Z-Wave Plus
|
Factory Reset
- Make sure the sensor is powered.
- Press and hold the TMP button.
- Wait for the visual LED indicator to glow yellow (4th position of the MENU).
- Release the TMP button.
- Click the TMP button once to confirm selection.
- After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the TMP button quickly, three times in a row.
- Wait for the inclusion process to end.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the TMP button quickly, three times in a row.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
KeyFob
|
FGKF-601 ZW5
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- Click O and – simultaneously.
- Click ∆ or X until LED is Yellow - reset the device.
- Click + to confirm selection, or is you do not wish to reset at this time, click – to exit the menu.
- The LED will pulse Yellow twice to confirm the device has been reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- LED will pulse White during the adding process.
- Wait for the inclusion process to end.
- Successful adding will be confirmed by the Z-Wave controller’s message.
- Successful inclusion will be confirmed by Hubitat Elevation™ and the remote LED will be Green.
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click O and – simultaneously.
- Click ∆ or X until LED is Green.
- Click + to confirm selection.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Motion Sensor ZW5
|
FGMS-001 ZW5
|
Motion Sensor
|
Z-Wave Plus
|
Factory Reset
- Open the cover
- Press and hold the B-button.
- Wait for visual indicator to glow Yellow (2nd menu position).
- Release the B button and then briefly click the B-button to confirm selection
- After few seconds the device will be reset, which is signaled with the red, fading visual indicator color.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the B button quickly, three times in a row.
- Wait for the inclusion process to end.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the B button quickly, three times in a row.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
RGBW Controller
|
FGRGBW-101
|
RGBW Controller
|
Z-Wave
|
Factory Reset
- Disconnect the supply voltage.
- Press and hold the B button located inside the RGBW Controllers casing.
- Connect the the supply voltage, while still holding the B button.
- Release the B button.
- The B channel will turn on (blue channel).
- Disconnect the power supply.
Join the Z-Wave Network
(Auto Inclusion)
- Make sure the RGBW Controller is not connected to a supply.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect voltage supply to auto-include the RGBW Controller.
- The RGBW Controller will be automatically recognized and included in the Z-Wave network.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
(Manual Inclusion)
- Make sure the RGBW Controller is not connected to a supply.
- To disable auto-inclusion press the B button briefly, after re-connecting the RGBW Controller to its supply voltage.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple click the B button or any switch connected to I1-I4 inputs.
- The RGBW Controller will be recognized and included in the Z-Wave network.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple click the B button or any switch connected to I1-I4 inputs.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Single Switch 2
|
FGS-213
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Switch off the mains voltage (disable the breaker).
- Remove the Switch 2 from the wall switch box.
- Switch on the mains voltage.
- Press and hold the B button to enter the menu until the visual LED indicator is Yellow.
- Quickly release and click the B button again.
- After few seconds the device will be restarted, which is signaled by the Red LED indicator color.
Join the Z-Wave Network
- Identify the S1 switch.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, three times press the S1 switch.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, three times press the S1 switch.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Wall Plug
|
FGWPB-111 / FGWPB-121
|
Outlet
|
Z-Wave Plus
|
Factory Reset
- Make sure the device is powered.
- Press and hold the button.
- Wait for the LED frame to glow yellow (3rd menu position).
- Release the button and then briefly click the button once to confirm the selection.
- After few seconds the device will restart with factory settings, which is signaled with the red frame color.
Join the Z-Wave Network
- Plug the device into a socket.
- The LED frame will glow red signaling it has not being added (If is doesn't you must first perform a general exclusion and then a factory reset).
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple click the button located on the casing.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- Plug the device into a socket.
- Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
- Quickly, triple click the button located on the casing.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Wall Plug
|
FGWPE-102
|
Outlet
|
Z-Wave
|
Factory Reset
- Press and hold the button located on the side.
- The device will cycle through GREEN, then VIOLET, and finally YELLOW for device reset.
- Release the button.
- Press the button again to confirm the selection and factory reset the device.
Join the Z-Wave Network
- Plug the device into a socket nearby the main Z-Wave controller.
- The LED frame will glow red signaling not being added (reset or remove the device otherwise).
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple click the button on the side of the device.
- The device will be included to the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple click the button on the side of the device.
- Plug the device into a socket nearby the main Z-Wave controller.
- The LED frame will glow green signaling being added (removing is not necessary otherwise).
- Quickly, triple click the button on the side of the device.
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Fibaro
|
Dimmer 2
|
FGS-212
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Switch off the mains voltage (disable the breaker).
- Remove the Dimmer 2 from the wall switch box.
- Switch on the mains voltage.
- Press and hold the B button to enter the menu until the visual LED indicator is Yellow.
- Quickly release and click the B button again.
- After few seconds the device will be restarted, which is signaled by the Red LED indicator color.
- The device enters the calibration mode.
Join the Z-Wave Network
- Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing).
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly press switch no. 1 or the B button three times.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly press switch no. 1 or the B button three times.
- The device will be excluded from the Z-Wave network.
- Dimmer 2 will start the calibration process
First Alert
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
First Alert
|
Smoke & Carbon Monoxide Combo Alarm
|
ZCOMBO-G
|
Smoke / CO Detector
|
Z-Wave
|
Factory Reset
- Power up the device with the test button held down for 10+ seconds
- The device will reset all Z-Wave settings and leave the network. NOTE: The device will not remain awake after resetting and will go into standby mode.
Join the Z-Wave Network
- Slide battery door open and insert batteries.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Slide battery door open, then remove and re-insert batteries.
- Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
GE/Jasco
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE
|
Link Bulb
|
Bulb
|
Zigbee
|
Factory Reset
- Turn OFF the light for 3 second.
- Turn ON the light for 3 seconds
- Repeat this process 5 times
- The bulb will dim and then flash once when successfully reset.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Turn the bulb on.
- The bulb will flash when connected to the hub.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Plug-in Dimmer
|
12718
|
Dimmer
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Plug-in Switch
|
12719/ZW4101
|
Switch
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Outdoor Plug-in Switch
|
12720/ZW4201
|
Switch
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Outlet
|
12721
|
Outlet
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Switch
|
12722
|
Switch
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Dimmer
|
12724
|
Dimmer
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Toggle Switch
|
12727
|
Switch
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Toggle Dimmer
|
12729
|
Dimmer
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press up and release the toggle switch to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Fan Control
|
12730/ZW4002
|
Fan Controller
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
- 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless fan control rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Plug-In Outdoor Switch
|
14284
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Unplug the switch from the outlet
- Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Fan Control
|
14287
|
Fan Controller
|
Z-Wave Plus
|
Factory Reset
- Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
- The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless fan control rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
- Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Tamper Resistant Outlet
|
14288
|
Outlet
|
Z-Wave Plus
|
Factory Reset
- Press the manual/program button 3 times, then press and hold the button for at least 3 seconds. The LED will blink 5 times to confirm.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Switch
|
14291
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
- The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart switch rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
- Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Dimmer
|
14294
|
Dimmer
|
Z-Wave Plus
|
Factory Reset
- Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
- The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
- Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Smart Motion Switch
|
26931
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Press and release the top button 10 times within five seconds.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom button on the smart switch to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom button on the smart switch to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Smart Motion Switch
|
26933
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Press and release the top button 10 times within five seconds. The LED will flash 3 times quickly confirming change
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top or bottom button on the smart switch to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the top button on the smart switch to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Plug-in Dimmer
|
28167
|
Dimmer
|
Z-Wave Plus
|
Factory Reset
- If plugged in, unplug the Dimmer from the receptacle.
- Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Plug-in Dimmer
|
28169
|
Dimmer
|
Z-Wave Plus
|
Factory Reset
- If plugged in, unplug the Dimmer from the receptacle.
- Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the manual/program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
Hinge Pin Smart Door Sensor
|
32563/ZW6301
|
Contact Sensor
|
Z-Wave Plus
|
Factory Reset
- Press and release the program button ten times quickly.
- The LED light will blink approximately eight times.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the program button on the device to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Single press and release the program button on the device to exclude it from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Switch
|
45856
|
Switch
|
Zigbee
|
Factory Reset
- Tap the top of the rocker (ON Switch) 10x quickly (short presses)
Join the Zigbee Network
- Remove power from the dimmer at the circuit breaker.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Restore power to the Smart Dimmer at the circuit breaker
- Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
- After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
- Note: LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GE/Jasco
|
In-Wall Dimmer
|
45857
|
Dimmer
|
Zigbee
|
Factory Reset
- Lift the air-gap switch at the bottom of the rocker to OFF position to power down the device.
- Hold down the UP button
- Push In the air-gap switch to ON position to power up the device.
- Release the UP button within 4 seconds of power up.
Join the Zigbee Network
- Remove power from the dimmer at the circuit breaker.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Restore power to the Smart Dimmer at the circuit breaker
- Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
- After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
- Note: LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
GoControl
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GoControl
|
Garage Door Controllers
|
GD00Z
|
Garage Door Opener
|
Z-Wave
|
Includes Linear GD00Z-2, GoControl GD00Z-4, Linear GD00Z-5, ADT GD00Z-6, GoControl GD00Z-7 and NuTone ND00Z
Factory Reset
- Reset the controller by pressing the Link button 5 times.
- A quick beep followed by a longer beep will indicate proper reset of the GD00Z series or ND00Z.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the Link button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and release the Link button.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
GoControl
|
Door / Window Sensor
|
WADWAZ-1
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
Join the Z-Wave Network
- Unscrew the screw fastening the rear cover and slide the rear cover down
- Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the sensor has not yet performed inclusion with the controller.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Once Hubitat Elevation™ discovers the device, the LED will stop blinking. If the LED does not stop blinking and is not discovered by your hub, relocate the WADWAZ-1 to within 100 feet (line of sight) of a Z-Wave repeater or your hub and restart Z-Wave Inclusion.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
Graber
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Graber
|
Motorized Shades
|
Shade
|
Z-Wave
|
Network Reset
- Press and hold the button on the headrail end cap for 7 seconds or until the shade jogs once.
- Release the button.
- NOTE: The will not reset the shade limits
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash Green.
- Release the button.
- Successful inclusion will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash Green.
- Release the button
- The shade will be excluded from the Z-Wave network.
Halo Labs
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Halo
|
Halo+
|
LS001A
|
Smoke/CO Detector
|
Zigbee
|
Factory Reset
- To reset, hold down center button for approximately 20+ seconds.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Once Halo greets you, it will automatically begin searching for a ZigBee network. Halo will glow for a couple minutes before timing out.
- To awaken the detector, double-tap the center button or hold the button for approximately 3+ seconds.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Hold down the center button for approximately 20+ seconds. Halo will reset all ZigBee settings and leave the network. .
Hampton Bay
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Hampton Bay
|
Wink Enabled Ceiling Fan Controller
|
MR101Z
|
Fan Controller
|
Zigbee
|
Factory Reset
- Turn off your fan for 3 seconds, then turn it on for 3 seconds (Repeat 5 times)
- The light will flash three times when the factory reset is successful.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Turn on your fan.
- When successful, the fan will turn on at low speed and the light will flash three times.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the controller
Hank
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Hank
|
One-Key Scene Controller
|
HKZW-SCN01
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- Press and holding the center "Z-button" for 20 seconds.
- Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
- Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Insert the battery.
- Triple click the center "Z-button".
- If inclusion is successful, the LED will blink blue for less than 5 seconds, and then it will remain solid for 15 seconds.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- If exclusion is successful, the LED will blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Hank
|
Four-Key Scene Controller
|
HKZW-SCN04
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- Press and holding the center "Z-button" for 20 seconds.
- Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
- Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Insert the battery.
- Triple click the center "Z-button".
- If inclusion is successful, the LED will blink blue for less than 5 seconds, and then it will remain solid for 15 seconds.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- If exclusion is successful, the LED will blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Hank
|
RGBW LED Bulb
|
HKZW-RGB01
|
Bulb
|
Z-Wave Plus
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle power to the bulb off and on 3 times quickly.
- Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
- If the exclusion is successful, the RGB BULB will quicly blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
- The bulb will remain warm white after the exclusion procedure is complete.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Make sure power to the bulb is disconnected and the RGB BULB is close to the hub.
- Insert the bulb into a socket and then turn it on.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle power to the bulb off and on 3 times quickly.
- Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
- If the exclusion is successful, the RGB BULB will quicly blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
- The bulb will remain warm white after the exclusion procedure is complete.
HomePro
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
HomePro
|
Exterior Appliance Module
|
ZRP110
|
Outlet
|
Z-Wave
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the button on the front of the module once
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the button on the front of the module once
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the button on the front of the module once
Homeseer
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Indicator Light Sensor
|
HS-FS100-L+
|
Light Sensor
|
Z-Wave Plus
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the Z-Wave button inside the sensor body for 10 seconds
- If successful, the LED will flash 5 times.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Perimeter Water Sensor
|
HS-FS100-W+
|
Water Sensor
|
Z-Wave Plus
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the Z-Wave button inside the sensor body for 10 seconds
- If successful, the LED will flash 5 times.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Wall Dimmer
|
HS-WD200+
|
Dimmer
|
Z-Wave Plus
|
Factory Reset
- Turn dimmer on by tapping the top of the paddle once.
- Quickly tap top of the paddle 3 times.
- If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Wall Switch
|
HS-WS200+
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Turn dimmer on by tapping the top of the paddle once.
- Quickly tap top of the paddle 3 times.
- If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Door/Window Sensor
|
HS-DS100+
|
Contact Sensor
|
Z-Wave Plus
|
Factory Reset
- Press and hold the Z-Wave button inside the sensor body for 20 seconds, the LED will stay on until the button is released.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
- If successful, the sensor body LED will blink briefly and then stay on for 3 seconds.
- If unsuccessful, the LED with blink briefly and then turn off. Should this happen, repeat the inclusion process.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple-click the Z-Wave button inside the sensor body.
- If successful, the LED will turn off within 1 second.
- If unsuccessful, the LED with blink for 5 seconds. Should this happen, repeat the exclusion process.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Homeseer
|
Leak Sensor
|
HS-LS100+
|
Water Sensor
|
Z-Wave Plus
|
Factory Reset
- Press and hold the Z-Wave button for 20 seconds. Release the button once the LED stops blinking and glows solidly
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click the Z-Wave button inside the sensor body once and wait for the process to finish.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple-click the Z-Wave button inside the sensor body. Wait for the inclusion process to finish.
IKEA
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IKEA TRÅDFRI
|
Warm White Bulb
|
1000 lm Warm White
|
Bulb
|
Zigbee
|
Factory Reset
- Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
- Wait for at least 10 seconds after reset is complete before attempting to pair the bulb.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has successfully joined the Zigbee network.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
- Wait for at least 10 seconds after reset is complete before attempting to pair the bulb again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IKEA TRÅDFRI
|
Outlet
|
Outlet
|
Zigbee
|
Factory Reset
- Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
- The LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
- Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
- The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
- The LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IKEA TRÅDFRI
|
Signal Repeater
|
Repeater
|
Zigbee
|
Factory Reset
- Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
- An LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
- Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
- The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
- The signal repeater will pair as Device. No driver will be assigned and it is not nessecary to have one since this device only repeats Zigbee radio signals.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
- Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
- The LED will pulse quickly and then pulse slowly when you release the internal button.
- Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
Inovelli
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Inovelli
|
In-Wall Switch
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Hold the UP button for 5 seconds when powered on
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Top button on the switch 6 times within 2 seconds.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Top button on the switch 6 times within 2 seconds.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Inovelli
|
Outlet
|
Outlet
|
Z-Wave Plus
|
Factory Reset
- Press and hold the top button for at least 3 seconds while you plug the outlet into a recepticle
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Once the controller is ready to include your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Once the controller is ready to exclude your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Inovelli
|
Switch Module
|
Switch
|
Z-Wave Plus
|
Factory Reset
- Factory reset is acomplished by performing a general exclusion on the device.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the center button 5 times within 1 second to exclude it in the Z-Wave network.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the center button 5 times within 1 second to include it in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the center button 5 times within 1 second to exclude it in the Z-Wave network.
IRIS
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Button
|
BTN900 |
Button
|
Zigbee
|
Factory Reset
- Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
- Upon a successful reset, the smart button will blink green indicating the device is now ready to pair.
- NOTE: The green light can be dim, if you're in a well lighted area this light could be difficult to see.
- If your button does not blink green check your battery, then retry from step 2.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- With the smart button, squeeze the two sides together by the ridges and gently pull them apart to reveal the battery compartment.
- Remove and re-insert the battery. When the smart button begins looking for your hub, the light around the button will blink green.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
- Upon a successful reset, the smart button will blink green indicating the device is now ready to pair.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- If your button does not blink green check your battery, then retry from step 2.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Care Pendant
|
PDT900 |
Button Controller
|
Zigbee
|
Factory Reset
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to blink.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Insert the supplied access tool into the small opening at the top of the pendant. Gently pry open the case to reveal the battery compartment.
- Insert the battery in the correct orientation. The pendant will light up and start blinking as it begins searching for your hub
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to blink.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Door/Window Sensor
|
DWS800 |
Contact Sensor
|
Zigbee
|
Factory Reset
- Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
- Reinsert the battery and immediately press the white reset button 8 times.
- Your Iris Contact Sensor should now be blinking green indicating it's ready to pair
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- On the large piece, remove the back by squeezing the semi-circles on either side.
- The sensor's LED will blink while searching for the hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
- Reinsert the battery and immediately press the white reset button 8 times.
- Your Iris Contact Sensor should now be blinking green indicating it's ready to pair
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Keyfob
|
KEY903 |
Presence Sensor
|
Zigbee
|
Factory Reset
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to blink.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Insert the battery in the correct orientation. The fob will light up and start blinking as it begins searching for your hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to blink.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Motion Sensor
|
MOT800 |
Motion Sensor
|
Zigbee
|
Factory Reset
- Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- On the large piece, remove the back by squeezing the raised edges on both sides.
- Insert the battery. The sensor's LED will blink while searching for the hub.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
- Remove the battery for at least 10 seconds. Reinsert the battery.
- As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.
- NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V1 Smart Plug
|
SPG800 |
Outlet
|
Zigbee
|
Factory Reset
- Remove the Smart Plug from the receptacle.
- Press and hold the button on the front for 15 seconds.
- Insert the Smart Plug back into the receptacle.
- Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Insert the Smart Plug into any wall outlet.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove the Smart Plug from the receptacle.
- Press and hold the button on the front for 15 seconds.
- Insert the Smart Plug back into the receptacle.
- Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Button
|
3460-L |
Button
|
Zigbee
|
Factory Reset
- Remove battery. Wait 10 seconds then re-insert battery.
- Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
- NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- The LED can be dim, if you're in a well lighted area this light could be difficult to see.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove battery. Wait 10 seconds then re-insert battery.
- Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
- NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
- The LED can be dim, if you're in a well lighted area this light could be difficult to see.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Door/Window Sensor
|
3320-L |
Contact Sensor
|
Zigbee
|
Factory Reset
- Slide off the battery cover, remove the battery and wait ten seconds.
- Using a paper clip, press and hold the reset button completely down while reinserting the battery.
- Hold for an additional two seconds and release. The contact sensor should begin blinking blue.
- NOTE: The reset button is a small black button above the battery.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove battery. Wait 10 seconds then re-insert battery.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Slide off the battery cover, remove the battery and wait ten seconds.
- Using a paper clip, press and hold the reset button completely down while reinserting the battery.
- Hold for an additional two seconds and release. The contact sensor should begin blinking blue.
- NOTE: The reset button is a small black button above the battery
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
Garage Door Opener
|
GD-00Z-1 |
Garage Door Opener
|
Z-Wave Plus
|
Factory Reset
- Unplug your device - wait 10 seconds
- Restore power to the device
- Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
Join the Z-Wave Network
- Perform a factory reset before attempting to join the Z-Wave network.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Ensure your Iris Garage Door Controller is plugged in, and the tilt sensor battery is active/working.
- Press the Link (Z-Wave) button once located on the left of the Iris Garage Door Controller.
- When your device triple beeps, it has successfully joined the Z-Wave network.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Once the controller is ready to exclude your device, press the Link (Z-Wave) button once located on the left side of the device.
- The garage door controller should give a short beep immediately followed by a long beep.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Keypad
|
3405-L |
Keypad
|
Zigbee
|
Factory Reset
- Remove the battery and wait ten seconds.
- Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
- Note: The factory reset process puts the security keypad back into pairing mode.
- Upon a proper reset the top right icon will be blinking green on your keypad.
- You may now insert the 2nd battery.
Join the Zigbee Network
- Perform a factory reset before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove battery. Wait 10 seconds then re-insert battery.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
- Note: The factory reset process puts the security keypad back into pairing mode.
- Upon a proper reset the top right icon will be blinking green on your keypad.
- You may now insert the 2nd battery.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V3 Keypad
|
iL02_1 |
Keypad
|
Zigbee
|
Factory Reset
- Remove only 1 AA battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
- A blinking blue light indicates the device is reset and ready to pair again.
Join the Zigbee Network
- Remove only 1 AA battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
- A blinking blue light indicates the device is reset and ready to pair again.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove only 1 AA battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
- A blinking blue light indicates the device is reset and ready to pair again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Motion Sensor
|
3326-L |
Motion Sensor
|
Zigbee
|
Factory Reset
- Remove the battery and wait 10 seconds
- Press and hold the reset button on the left side of the device as you reinsert the battery.
- Hold for an additional two seconds and release.
- Note: The reset button is a small white button located on the side of the motion sensor.
- Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
- A blinking blue light indicates the device is reset and ready to pair again.
Join the Zigbee Network
- Factory reset the device before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove the battery for 10 seconds and re-insert.
- Replace the battery cover. The sensor's blue LED will flash while searching for the hub.
- Once paired the LED will stop blinking.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press and hold the reset button on the left side of the device as you reinsert the battery.
- Hold for an additional two seconds and release.
- Note: The reset button is a small white button located on the side of the motion sensor.
- Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
- A blinking blue light indicates the device is reset and ready to pair again.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V3 Motion Sensor
|
iL07_1 |
Motion Sensor
|
Zigbee
|
Factory Reset
- Remove the battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
- A blinking blue light indicates the device is ready to pair.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove the battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
- A blinking blue light indicates the device is ready to pair.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove the battery and wait ten seconds.
- Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
- A blinking blue light indicates the device is ready to pair.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Smart Plug
|
3210-L |
Outlet
|
Zigbee
|
Factory Reset
- Remove the Smart Plug from the outlet and wait ten seconds.
- Press and hold the small white button on the front of the plug.
- While holding the button, insert the Smart Plug back into the outlet.
- As soon as the LED on the front of the plug lights up, release the button.
- If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.
Join the Zigbee Network
- Factory reset the device before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Insert your smart plug into any wall outlet. Your smart plug should be blinking blue, that means it's in pairing mode.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press and hold the small white button on the front of the plug.
- While holding the button, insert the Smart Plug back into the outlet.
- As soon as the LED on the front of the plug lights up, release the button.
- If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
V2 Smart Fob
|
3450-L |
Button Controller
|
Zigbee
|
Factory Reset
- Twist open the battery cover on the back of the Smart Fob.
- Remove the battery and wait ten seconds
- Reinstall the battery with the positive side facing you.
- Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
- Confirm that the fob has been reset by checking that the fob's background light is flashing blue. If it does not do this, check the battery and retry from step 2.
Join the Zigbee Network
- Factory reset the device before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
- The Smart Fob's LED will blink blue while searching for the hub.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Twist open the battery cover on the back of the Smart Fob.
- Remove the battery and wait ten seconds
- Reinstall the battery with the positive side facing you.
- Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
IRIS
|
Smart Water Sensor
|
3315-L |
Water Sensor
|
Zigbee
|
Factory Reset
- Remove the cover from the sensor, then remove the battery for at least 10 seconds.
- Press and hold the reset button while reinserting the battery.
- Hold for an additional two seconds and release.
- A successful reset will be indicated by a blinking blue light on your sensor
Join the Zigbee Network
- Factory reset the device before attempting to pair.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove the battery and wait ten seconds.
- Re-insert the battery
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove the cover from the sensor, then remove the battery for at least 10 seconds.
- Press and hold the reset button while reinserting the battery.
- Hold for an additional two seconds and release.
- A successful reset will be indicated by a blinking blue light on your sensor
KEEN Home
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
KEEN Home
|
Smart Vent
|
Vent
|
Zigbee
|
Factory Reset
- Press the black button on the back inside of the Smart Vent battery compartment five times.
- You will know that the Smart Vent has been properly reset when the LED starts double blinking green
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Removed the battery cartridge and reinsert it to bring the vent online.
- Press the black button on the back inside of the Smart Vent battery compartment five times.
- This should force the vent into join-mode once again.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press the black button on the back inside of the Smart Vent battery compartment five times.
- You will know that the Smart Vent has been properly reset when the LED starts double blinking green
Kwikset
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Kwikset
|
SmartCode
|
910 / 912 / 914
|
Lock
|
Z-Wave
|
Factory Reset
- Remove battery pack
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
- Perform the door handing process again.
- Press and hold the Lock button while installing battery pack.
- Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
- If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
Join the Z-Wave Network
- Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press button A on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
- If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press button A on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press button A on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Kwikset
|
SmartCode
|
910 / 912 / 914
|
Lock
|
Zigbee
|
Factory Reset
- Remove battery pack
- Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
- Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
- Perform the door handing process again.
- Press and hold the Lock button while installing battery pack.
- Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
- If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
Join the Zigbee Network
- Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Press button A on the lock 4 times to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
- If pairing is unsuccessful, press button B on the lock 9 times and repeat the pairing process.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Press button B on the lock 9 times.
Leak Intelligence
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Leak Intelligence
|
Leak Gopher
|
Valve
|
Z-Wave
|
Factory Reset
- Unplug your device - wait 10 seconds
- Restore power to the device
- Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-Wave button once.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Exclusion the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Once the controller is ready to exclude your device, press the Z-Wave button once.
Leviton
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Leviton
|
4-Scene Controller
|
VRCS4
|
Button Controller
|
Z-Wave
|
Factory Reset
- On the 4-Scene controller, press and hold buttons 1 and 3.
- Wait approximately 5 seconds until the LED turns amber and then solid red.
- Release the buttons and the 4-Scene controller will be reset. NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.
Join the Z-Wave Network
Leaving the Z-Wave Network
Linear
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Linear (GoControl)
|
Door / Window Sensor
|
WADWAZ-1
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- The LED on the sensor will stop blinking
- Watch the status in the device details page to confirm proper operation.
Exclusion the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Tamper switch of WADWAZ-1 for 1 second and release to exclude the device form the Z-wave network.
- The LED light will flash continuously when the sensor is in the excluded condition.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Linear (GoControl)
|
PIR Motion Detector
|
WAPIRZ-1
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- The LED on the sensor will stop blinking
- Watch the status in the device details page to confirm proper operation.
Exclusion the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Tamper switch of WAPIRZ-1 for 1 second and release to exclude the device form the Z-wave network.
- The LED light will flash continuously when the sensor is in the excluded condition.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Linear (GoControl)
|
Siren / Strobe
|
WA105DBZ-1
|
Siren
|
Z-Wave
|
Factory Reset
- Factory reset is achieved by performing a general exclusion.
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- The LED on the sensor will stop blinking
- Watch the status in the device details page to confirm proper operation.
Exclusion the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
- The LED light will flash continuously when the sensor is in the excluded condition.
Lutron
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Lutron Dimmers and Switches
|
Dimmer / Switch
|
Lutron Clear Connect
|
Factory Reset
- Tap the "On" button quickly three times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button three more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Caséta Smart Bridge Pro
|
L-BDGPRO2
|
Bridge
|
Lutron Clear Connect
|
Network Reset
- First, press and hold the black button on the back of your Smart Bridge for 20 seconds.
Factory Reset
- Quickly triple tap and hold the Add button. DO NOT release after the third tap.
- Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
- Release the button and quickly perform another triple tap of the button. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
- The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
NOTE: Lutron does not recommend factory resetting a Smart Bridge Pro unless advised by a member of the Lutron technical support team.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Pico Remote
|
PJ2-
|
Button Controller
|
Lutron Clear Connect
|
Factory Reset
- Tap the "On" button quickly three times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button three more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Radio RA2 Keypads
|
Keypad
|
Lutron Clear Connect
|
Factory Reset
- Tap the "On" button quickly three times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button three more times.
- The RA2 keypad has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Radio RA2 Main Repeater
|
RR-MAIN-REP
|
Repeater
|
Lutron Clear Connect
|
Factory Reset
- Triple tap and hold the Test button on a Main Repeater. DO NOT release the button after the third tap.
- Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately 3 seconds).
- Release the Test button and immediately triple tap it again. All the LEDs will flash red quickly.
- When the LEDs stop flashing, the Main Repeater has been returned to factory settings
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Radio RA2 Occupancy Sensors
|
Motion Sensor
|
Lutron Clear Connect
|
Factory Reset
- Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)
- Quickly triple tap and hold the Test, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
- Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
- Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)
- Quickly triple tap and hold the Test or Light button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
- Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
- Radio Powr SavrTM Occupancy/Vacancy Wall-Mounted Sensor
- Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
- Release the button and triple tap the button again until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Sensor has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Radio RA2 Select Main Repeater
|
RR-SEL-REP2
|
Repeater
|
Lutron Clear Connect
|
Factory Reset
- Quickly triple tap and hold down any button on the Main Repeater. DO NOT release after the third tap.
- Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash red slowly (approximately once per second).
- Release the button and quickly perform another triple tap of the button. The Main Repeater LEDs will flash green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The Main Repeater and system components have now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
RadioRA2 VCRX Visor Control Receiver
|
RR-VCRX
|
Garage Controller
|
Lutron Clear Connect
|
Factory Reset
- Quickly triple tap and hold any button (except Learn) on the VCRX. DO NOT release after third tap.
- Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
- Release the button and triple tap the button again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
- The VCRX has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Serena Shades
|
Shade Control
|
Lutron Clear Connect
|
Factory Reset
- Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
- Immediately tap the shade button quickly three more times, until the shade button LED blinks green rapidly, then blinks red/green three times, and turns off.
- The Serena shade has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Sivoia QS Triathlon Shades
|
Shade Control
|
Lutron Clear Connect
|
Factory Reset
- Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
- Immediately tap the shade button quickly three more times, until the shade button LED blinks Green rapidly, then blinks Red/Green three times, and turns off.
- The Sivoia shade has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
RadioRA2 Fan Control
|
RRD-2ANF |
Fan Controller
|
Lutron Clear Connect
|
Factory Reset
- Triple tap the tapswitch on a control. DO NOT release after the third tap.
- Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
- Release the tapswitch and immediately triple tap the tapswitch again.
- The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lutron
|
Lutron Caséta Fan Control
|
PD-FSQN |
Fan Controller
|
Lutron Clear Connect
|
Factory Reset
- Tap the "On" button quickly three times, holding on the last press.
- Continue to hold the "On" button until the light begins to flash quickly.
- Release the button, then immediately tap the button three more times.
- All paired Pico remote controls are removed and all settings are returned to factory default.
Join the Lutron Clear Connect network
- See the Lutron Integrator documentation.
Leaving the Lutron Clear Connect network
- From the device's details page, select Remove Device, then Remove
- Perform a factory reset on the device
LUX
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Lux
|
KONOz
|
Thermostat
|
Zigbee
|
Factory Reset
- Access the installation settings by going to the main menu and selecting the gear icon.
- You will see “IS” on the screen and will be prompted to select “yes” or “no”.
- Select “yes” to access the installation settings.
- Rotate the knob to view settings and press the knob to confirm.
- Once in the installer settings, rotate the knob to 99.
- Press the knob to confirm, then press and hold the knob for 3 seconds.
Join the Zigbee Network
- Perform factory reset.
- KONOz is now ready to be configured for your heating and cooling system. The KONOz will guide you through the initial system configuration.
- After confirming your system settings, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET” to establish a connection.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Perform factory reset.
MCO Home
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
MCO Home
|
Dimmer Switch
|
MH-DT311
|
Dimmer
|
Z-Wave
|
Factory Reset
- Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power.
- The factory setting will be restored.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press 3 times on "+" or "-" button to add the device. If successful, the green LED blinks 4 times.
- Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED blinks 4 times.
- Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
Monoprice
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Door/Window Sensor |
24259
|
Contact Sensor
|
Z-Wave Plus
|
Factory Reset
- To reset the sensor, press and hold the Z-button for about 20 seconds.
- The LED will change from steadily illuminated to blinking then back to steadily illuminated, indicating that the reset operation was successful.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Rapidly press the Z-button 3 times to include the device in the network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Rapidly press the Z-button 3 times to exclude the device from the network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Plug-In Dimmer |
11994
|
Dimmer
|
Z-Wave
|
Factory Reset
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Plug-In ON/OFF |
11995
|
Outlet
|
Z-Wave
|
Factory Reset
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Recessed Door/Window sensor |
15268
|
Contact Sensor
|
Z-Wave Plus
|
Factory Reset
- Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for 2 seconds then disappear.
- If linking was unsuccessful, the LED will continue to blink if you tap its button.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Z-button on your Sensor. If your switch has been successfully unlinked to your network, its LED will start to blink for a short time.
- If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Door/Window Sensor |
15270
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
PIR Motion Sensor with Temperature |
15271
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Plug-in Outlet |
15654
|
Outlet
|
Z-Wave Plus
|
Factory Reset
- Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can jooin the Hubitat Elevation™ Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Triple-click the Z-Button. The plug-in will be removed from your Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
4 in 1 motion sensor |
15902
|
Motion Sensor
|
Z-Wave Plus
|
Factory Reset
- Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network and has returned it to a factory state.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Momentarily press the Program Switch
- The LED should blink 5 times indicating the sensor has not yet been included in the Z-Wave network.
- If the LED blinks only 1 time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
- Momentarily press the button again after it blinks 5 times, to automatically include the sensor in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Monoprice
|
Smart Plug and Repeater |
27481
|
Outlet
|
Z-Wave Plus
|
Factory Reset
- Ensure that the smart plug is inserted into an AC outlet.
- Press and hold the Z-Button on the smart plug for more than 20 seconds.
- The LED indicator will illuminate yellow steadily for about 2 seconds.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Rapidly press the Z-button 3 times to include the device in the network.
Testing the Smart Plug Z-Wave connection
You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.
To begin testing, press and hold the Z button for 6-9 seconds, releasing the button when the RGB LED illuminates violet.
- Note: The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
- Blinking Green: The RGB LED will blink green while the smart plug is attempting to establish a connection with the main controller.
- Solid Green: The RGB LED will illuminate green for about 2 seconds to indicate that direct communications are stable.
- Blinking Orange: The RGB LED will blink orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
- Solid Orange: The RGB LED will illuminate orange for about 2 seconds to indicate that the communication quality is moderate.
- Solid Red: The RGB LED will illuminate red for about 2 seconds to indicate that they communications attempt has failed.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Rapidly press the Z-button 3 times to exclude the device from the network.
- The RGB LED will blink orange while the smart plug is being removed.
- The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate orange steadily for about 2 seconds.
Neo
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
Door/Window Sensor |
NAS-DS01ZE
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Remove the cover of contact sensor main body.
- Make sure the sensor is connected to power source.
- Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
- Release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times.
- The contact sensor will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
Door/Window Sensor |
NAS-DS02ZU
|
Contact Sensor
|
Z-Wave
|
Factory Reset
- Remove the cover of contact sensor main body.
- Make sure the sensor is connected to power source.
- Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
- Release the button.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times.
- The contact sensor will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
Motion Sensor |
NAS-PD01ZU-T
|
Motion Sensor
|
Z-Wave
|
Factory Reset
- Remove the sensor’s cover.
- Make sure the sensor is connected to power source.
- Press the code button for 10 seconds, the LED will flash red for 1 time.
- Release the code button.
- NOTE: When the PIR is being restored to factory settings, please make sure a power source is connected.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times.
- The motion sensor will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
Power Plug |
NAS-WR02Z
|
Outlet
|
Z-Wave
|
Factory Reset
- Press and hold the code button on the front of the outlet for 10 seconds.
- When the LED flashes, release the button.
- When the outlet has been reset, the LED will flash on and off 5 times within a 2 second period.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times.
- The device will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the code button, the LED light will flash for 5 times and the device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
One Key SOS |
NAS-RC03ZU
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the code button for 10 seconds.
- Release the Code button. Note: Do not power off during factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the red SOS alarm button.
- The device will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the red SOS alarm button and the device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Neo
|
One Key SOS and Remote Control |
NAS-RC03ZU
|
Button Controller
|
Z-Wave
|
Factory Reset
- Press and hold the code button for 10 seconds.
- Release the Code button. Note: Do not power off during factory reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the red SOS alarm button.
- The device will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Quickly, triple-click the red SOS alarm button and the device will be excluded from the Z-Wave network.
NodOn
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NodOn
|
Octan Remote |
CRC-3US-1
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- A simultaneous long press (1sec) on O and – will perform this factory reset.
- The LED will blink red and green to validate the reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Simultaneously push on the solid circle and the + for 1sec.
- The LED glows in pink to confirm the selection
- Push on the solid circle within 10 seconds.
- The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure.
- The device will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Simultaneously push on the solid circle and the + for 1sec.
- The LED glows in pink to confirm the selection
- Push on the solid circle within 10 seconds.
- The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure
- The device will be excluded from the Z-Wave network.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NodOn
|
Soft Remote |
CRC-3US-6
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- A simultaneous long press (1sec) on O and – will perform this factory reset.
- The LED will blink red and green to validate the reset.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Simultaneously push on the solid circle and the + for 1sec.
- The LED glows in pink to confirm the selection
- Push on the solid circle within 10 seconds.
- The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure.
- The device will be detected and included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Simultaneously push on the solid circle and the + for 1sec.
- The LED glows in pink to confirm the selection
- Push on the solid circle within 10 seconds.
- The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure
- The device will be excluded from the Z-Wave network.
NYCE
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NYCE
|
Curtain Motion Sensor |
NCZ-3045-HA
|
Motion Sensor
|
Zigbee
|
Factory Reset
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to join the device to the Zigbee network.
- The LED will flash in the following sequences:
- Yellow - Red - Yellow flashes indicate it is searching for a network to join.
- Yellow - Green - Yellow flashes indicate the device is being configured.
- 3 Green flashes indicate the device has sucessfully joined the network.
- 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NYCE
|
Ceiling Motion Sensor |
NCZ-3043-HA
|
Motion Sensor
|
Zigbee
|
Factory Reset
- Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
- Inside the battery compartment is a small button on the side of the circuit board.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
- Inside the battery compartment is a small button on the side of the circuit board.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to join the device to the Zigbee network.
- The LED will flash in the following sequences:
- Yellow - Red - Yellow flashes indicate it is searching for a network to join.
- Yellow - Green - Yellow flashes indicate the device is being configured.
- 3 Green flashes indicate the device has sucessfully joined the network.
- 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
- Inside the battery compartment is a small button on the side of the circuit board.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NYCE
|
Motion Sensor |
NCZ-3041-HA
|
Motion Sensor
|
Zigbee
|
Factory Reset
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to join the device to the Zigbee network.
- The LED will flash in the following sequences:
- Yellow - Red - Yellow flashes indicate it is searching for a network to join.
- Yellow - Green - Yellow flashes indicate the device is being configured.
- 3 Green flashes indicate the device has sucessfully joined the network.
- 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
- Inside the battery compartment at the top, is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NYCE
|
Garage Door (Tilt) Sensor |
NCZ-3014-HA
|
Contact Sensor
|
Zigbee
|
Factory Reset
- Slide open the Garage Door (Tilt) Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide open the Garage Door (Tilt) Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to join the device to the Zigbee network.
- The LED will flash in the following sequences:
- Yellow - Red - Yellow flashes indicate it is searching for a network to join.
- Yellow - Green - Yellow flashes indicate the device is being configured.
- 3 Green flashes indicate the device has sucessfully joined the network.
- 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Slide open the Garage Door (Tilt) Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
NYCE
|
Door/Window Sensor |
NCZ-3011-HA
|
Contact Sensor
|
Zigbee
|
Factory Reset
- Slide open the Door/Window Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide open the Door/Window Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Press the button 4 times to join the device to the Zigbee network.
- The LED will flash in the following sequences:
- Yellow - Red - Yellow flashes indicate it is searching for a network to join.
- Yellow - Green - Yellow flashes indicate the device is being configured.
- 3 Green flashes indicate the device has sucessfully joined the network.
- 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Slide open the Door/Window Sensor’s top housing.
- Inside the battery compartment is a small button.
- Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
- Pressing the button 10 times will leave the network and reset the device to factory defaults.
- The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.
Orbit
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Orbit
|
Smart Hose Faucet Timer |
27087
|
Irrigation Controller
|
Zigbee
|
Factory Reset
- Insert two AA alkaline batteries and re-insert the tray.
- Press the RESET button 5 times in rapid secession.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Slide out the battery tray on the back of the timer.
- Insert two AA alkaline batteries and re-insert the tray.
- NOTE: Firmly replace the battery tray to ensure water resistance and increase battery life. You will know the battery tray is fully inserted if it does not pull out easily.
- Turn the dial to AUTO.
- When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
- NOTE: The timer will remain in pairing mode for 10 minutes or until paired. If pairing is not successful after 10 minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button 5 times in rapid secession.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press the RESET button 5 times in rapid secession.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Orbit
|
12-Station Sprinkler Controller |
27396
|
Irrigation Controller
|
Zigbee
|
Factory Reset
- Ensure the controller is connected to power.
- Press the SYNC button 5 times in rapid secession.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Ensure the controller is connected to power.
- Turn the dial to AUTO.
- When the controller is first connected to power, it will automatically attempt to connect.
- NOTE: If pairing is not successful after 10 minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button 5 times in rapid succession
- The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words SMART MODE will appear on the screen.
- Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
- Watch the status in the device details page to confirm proper operation
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove
- Press the SYNC button 5 times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for 5 seconds to cancel re-pairing.
Orvibo
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Obvibo
|
Motion Sensor
|
SN11
|
Motion Sensor
|
Zigbee
|
Factory Reset
- Hold down the reset button on the front of the motion sensor until the Green light goes out.
- This will disconnect the sensor from the Zigbee network.
- Short-press the reset button and the Green light will flash slowly.
- The sensor is now in pairing mode.
Join the Zigbee Network
- Remove the cover by rotating it counterclockwise
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Hold down the reset button on the front of the motion sensor until the Green light goes out.
- This will disconnect the sensor from the Zigbee network.
- Short-press the reset button and the Green light will flash slowly.
- The sensor is now in pairing mode.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Hold down the reset button on the front of the motion sensor until the Green light goes out.
- This will disconnect the sensor from the Zigbee network.
OSRAM
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Osram
|
Lightify Flex RGBW
|
73698
|
Bulb
|
Zigbee
|
Factory Reset
- Start with the Light Strip powered ON.
- Repeat 5 times - Uplug for 1 second and then plug in for 1 second
- On the fifth time plugging in the Light Strip, leave it plugged in
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Start with the Light Strip powered ON.
- Repeat 5 times - Uplug for 1 second and then plug in for 1 second
- On the fifth time plugging in the Light Strip, leave it plugged in
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Start with the Light Strip powered ON.
- Repeat 5 times - Uplug for 1 second and then plug in for 1 second
- On the fifth time plugging in the Light Strip, leave it plugged in
- After about 3 seconds, the Light Strip will flash rapidly 3 times to show a successful reset and ready for pairing.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Osram
|
All smart bulbs
|
Bulb
|
Zigbee
|
Factory Reset
- Turn the light off
- Turn the light on for three 3 seconds
- Turn the light off
- Repeat this cycle 5 times
- Wait 10 seconds for the light to blink 3 times
- Repeat these steps if the light does not blink three times
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Turn the light off
- Turn the light on for three 3 seconds
- Turn the light off
- Repeat this cycle 5 times
- Wait 10 seconds for the light to blink 3 times
- Repeat these steps if the light does not blink three times
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Turn the light off
- Turn the light on for three 3 seconds
- Turn the light off
- Repeat this cycle 5 times
- Wait 10 seconds for the light to blink 3 times
- Repeat these steps if the light does not blink three times
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Osram
|
Smart Outdoor Plug
|
G11028081
|
Outlet
|
Zigbee
|
Factory Reset
NOTE: Reset method may vary by firmware version
Method 1
- Hold the button for 30 seconds
- The outdoor plug will click 5 times
- The outdoor plug is now reset and ready for pairing
Method 2
- Turn the outdoor plug off
- Turn the outdoor plug on for three 5 seconds
- Turn the outdoor plug off
- Repeat this cycle 5 times
- The outdoor plug is now reset and ready for pairing
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- See factory reset instructions above to reset the outdoor plug and ready it for pairing . The required steps will vary by firmware version.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- See factory reset instructions above. The required steps will vary by firmware version.
Philips Hue
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Philips Hue
|
Dimmer Switch
|
73698
|
Button Controller
|
Zigbee
|
Factory Reset
- Turn the dimmer switch over and use a straightened paperclip to press the setup button on the back for 1 second.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Turn the dimmer switch over and use a straightened paperclip to press the setup button on the back for 1 second.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Turn the dimmer switch over and use a straightened paperclip to press the setup button on the back for 1 second.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Philips Hue
|
Motion Sensor
|
473389 |
Motion Sensor
|
Zigbee
|
Factory Reset
- On the back of the motion sensor, and use a straightened paperclip to press the setup button for 1 second.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- On the back of the motion sensor, and use a straightened paperclip to press the setup button for 1 second.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- On the back of the motion sensor, and use a straightened paperclip to press the setup button for 1 second.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Philips Hue
|
All Hue lights
|
Bulb
|
Zigbee
|
Factory Reset
- You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
- Turn on the light on to be reset, ensuring other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
- Hold the remote within 4 inches of the light.
- Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the light starts flashing on and off.
- When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will blink green, indicating the ligh has been factory reset.
Join the Zigbee Network
- Using a Hue dimmer, factory reset the light as described above.
- Disconnect the light from mains power.
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Power on the light
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Using a Hue dimmer, factory reset the light as described above.
Qubino
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush 1 Relay
|
ZMNHAD3
|
Relay
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush 1D Relay
|
ZMNHND3
|
Relay
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 5 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush 2 Relay
|
ZMNHBD3
|
Relay
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush Shutter DC
|
ZMNHOD3
|
Relay
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush Shutter
|
ZMNHCD3
|
Relay
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush ON/OFF Thermostat
|
ZMNHID3
|
Thermostat
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 5 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Qubino
|
Flush Dimmer
|
ZMNHDD3
|
Dimmer
|
Z-Wave Plus
|
Factory Reset
- Connect the device to the power supply
- Within the first 60 seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal 5 times within 3 seconds (5 times change switch state).
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
- NOTE: By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Connect the device to the power supply (with the temperature sensor already connected*).
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds. The device has to get On/Off signal 3 times, meaning 3 times push on the push button or 6 times flip of a switch.
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between 2 and 6 seconds
- NOTE: *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Toggle the switch connected to the I1 terminal 3 times within 3 seconds
- If the device is powered by 24 V SELV supply, press and hold the S (Service) button between
Remotec
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Remotec
|
Relay / Fixture Switch
|
ZFM-80US/DA065
|
Relay
|
Z-Wave
|
Factory Reset
- Factory reset is accomplished by excluding the device from the Z-Wave netowrk
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click once on the PROG button or and external attached switch.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click once on the PROG button or and external attached switch.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click once on the PROG button or and external attached switch.
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Remotec
|
ZRC-90 Scene Master
|
REMEZRC90
|
Button Controller
|
Z-Wave Plus
|
Factory Reset
- Press and keep holding R button not less than 10 seconds.
- Release R button then triple click on the same R button within 2 seconds.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press L & R buttons simultaneously until the LED lights up to add the device to the Z-Wave network. The LED will keep flashes slowly.
- Press the program button. The LED will flash once, then remain off if the device is included into the Z-Wave network.
- If the LED flashes 6 times rapidly, then remains off, the device has faililed to be included in the Z-Wave network.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Click once on the R button to remove the device from the Z-Wave network. The LED will continue flashing slowly.
- Press the program button. The LED will flash once, then remain off if the device is excluded from the Z-Wave network.
- If the LED flashes 6 times rapidly, then remains off, the device has faililed to be excluded in the Z-Wave network.
- Peform a factory reset and repeat the above steps to exclude the device from the Z-Wave network.
Salus
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Salus
|
Smart Plug
|
SP-600
|
Outlet
|
Zigbee
|
Factory Reset
- Press the button on the outlet for 10 seconds.
- The light surrounding the button will flash RED 5 times, and will then go out.
Join the Zigbee Network
- From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
- See Discovering your devices for detail instructions.
- Press the button on the outlet for 10 seconds.
- The light surrounding the button will flash RED 5 times, and will then go out.
- If the device is not discovered by Hubitat Elevation™, then unplug the outlet for 10 seconds and plug it in again. It should now be discovered by the hub.
Leaving the Zigbee Network
- From the device's details page, select Remove Device, then Remove.
- Press the button on the outlet for 10 seconds.
- The light surrounding the button will flash RED 5 times, and will then go out.
Radio Thermostat Company of America
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Radio Thermostat Company of America
|
Thermostat
|
CT-101
|
Thermostat
|
Z-Wave
|
Factory Reset
- The thermostat must be in OFF mode.
- Wait until the radio wave icons on the left side of the screen stop blinking then touch the screen once to turn on the back light and then hold the center of the screen for about 8 seconds until the thermostat beeps.
Factory Reset (Alternate Method)
- Place the CT101 in the off position by pressing mode button until OFF is shown at the top left of the screen.
- Press the menu button
- Press and hold the center of the screen for about 5 sec or until the screen changes then release.
- You will see two arrows. First press the up arrow and wait for the count down.
- Now press the down arrow and again, wait for the count down.
- All parameter values will be restored to defaults and a message is sent to any radio module installed to instruct the module to restore its own default values.
- The thermostat will now resets itself.
- Press the house to get back to the main screen.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press/Touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will blink.
- When a device has joined a network the LINK icon will appear under the radio tower.
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press/Touch the MATE button on the MENU screen. A large r1 will be displayed.
- This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will blink.
- When a device has excluded from the network, the LINK icon will disappear under the radio tower.
Schlage
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Schlage
|
Connect Deadbolt
|
BE-469
|
Lock
|
Z-Wave
|
Factory Reset
- Disconnect the batteries
- Press and hold the outside Schlage button
- While holding the outside Schlage button, then reconnect the batteries.
- Release the Outside Schlage Button. NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.
- To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
- If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.
Join the Z-Wave Network
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Schlage button
- Enter the 6 digit programming code
- Press 0
- A √ indicates the lock successfully joined the Z-Wave network, while an X indicates that it did not successfully join the network
Verify Z-Wave connection status from the lock
- Remove the battery cover
- Disconnect the battery connector
- While watching the inside Schlage button, reconnect the battery connector
- The inside Schlage button will blink if the lock is enrolled
Exclusion from the Z-Wave Network
- From the device's details page, select Remove Device, then Remove
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the Schlage button
- Enter the 6 digit programming code
- Press 0
- A √ indicates the lock was successfully excluded the Z-Wave network, while an X indicates that it did not successfully leave the network
Utilitech
Brand
|
Device
|
Product Number
|
Device Type
|
Protocol
|
Utilitech
|
Indoor Siren
|
TSE07
|
Siren
|
Z-Wave
|
Factory Reset
- Remove the battery cover
- Press the pairing button in between the batteries 8 times, one second apart
Join the Z-Wave Network
- Remove the battery cover
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the paring button once
Exclusion from the Z-Wave Network
- Remove the battery cover
- From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
- See Discovering your devices for detail instructions.
- Press the paring button once
*Note: Aeotec was formerly known as Aeon Labs.