Difference between revisions of "Join and Reset Instructions"

From Hubitat Documentation
Jump to: navigation, search
(Added IKEA Trådfri 1000 lm Warm Whilte Bulb)
m
 
(77 intermediate revisions by the same user not shown)
Line 1: Line 1:
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into '''Paring Mode''' using the manufacturer's instructions, Z-Wave devices must be '''Excluded''' from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a '''General Exclusion''' in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show '''Unknown Device Excluded''' in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
+
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
  
 
=='''<big>ADT</big>'''==
 
=='''<big>ADT</big>'''==
Line 18: Line 18:
  
 
#Remove the cover by rotating it counterclockwise
 
#Remove the cover by rotating it counterclockwise
#Press and hold the Connect button for 5 seconds
+
#Press and hold the Connect button for '''5''' seconds
#After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode.
+
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 27: Line 27:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the Connect button for 5 seconds
+
#Press and hold the Connect button for '''5''' seconds
#After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode
+
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 51: Line 51:
  
 
#Use the provided pin to press and hold the reset button for 10 seconds.
 
#Use the provided pin to press and hold the reset button for 10 seconds.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 57: Line 57:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 79: Line 79:
  
 
#Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
 
#Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 85: Line 85:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Hold down the off (circle) button for 10 seconds until it blinks green 3 times.
+
#Hold down the off (circle) button for '''10''' seconds until it flashes green '''3''' times.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 106: Line 106:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 113: Line 113:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 132: Line 132:
 
|<div style="text-align: center;">'''<big>ZW056</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW056</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking as a confirmation.
+
#Your Doorbell will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your Doorbell Gen5, and its LED will blink rapidly to indicate that it is communicating.
+
#Press the Action Button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
#If your Doorbell has been successfully linked to your network, its LED will become solid for 2 seconds, then stop. If linking was unsuccessful, the LED will blink when you tap its button.
+
#If your Doorbell has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop. If linking was unsuccessful, the LED will flash when you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 151: Line 151:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Doorbell.
 
#Press the Action Button on your Doorbell.
#If your Doorbell has been successfully unlinked to your network, its LED will begin to blink slowly indicating it is ready to be paired to a new network..
+
#If your Doorbell has been successfully unlinked to your network, its LED will begin to flash slowly indicating it is ready to be paired to a new network.
  
 
<hr />
 
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Doorbell 6</big>'''</div>
 +
|<div style="text-align: center;">'''<big>ZW162-A</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press and hold the Action button for '''20''' seconds
 +
#Within '''2-5''' seconds, the test doobell sound will run, then stop after '''5''' seconds has elapsed.
 +
#From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
 +
#After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 +
#With the LED pulsing, release the Action button, and the Doorbell 6 will be reset to factory defaults.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#Power Doorbell 6 through the provided power adapter.
 +
#Ensure that Doorbell 6 LED is flashing slowly.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Tap the Doorbell 6 Action Button once.
 +
#If Doorbell 6 has successfully paired to your Z-Wave gateway, the LED will be a solid color for '''30''' seconds, then turn off.
 +
#If is fails to join the Z-Wave network, the LED will flash slowly.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Action Button '''6''' times in '''2''' seconds.
 +
#If your Doorbell 6 has been successfully unpaired from the Z-Wave network, its LED will begin to flash slowly, indicating it is ready to join a Z-Wave network again.
 +
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 165: Line 203:
 
|<div style="text-align: center;">'''<big>ZW112</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW112</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
 
#Press and hold Door Window Sensor 6 Action button
 
#Press and hold Door Window Sensor 6 Action button
 
#Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
 
#Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
#If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
+
#If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the button on the Door Window Sensor 6
 
#Tap the button on the Door Window Sensor 6
#The LED will blink green to indicate successful inclusion.
+
#The LED will flash green to indicate successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 199: Line 237:
 
|<div style="text-align: center;">'''<big>ZW120</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW120</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
|}
  
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once to include the door/window sensor.
 
#Press the Action Button once to include the door/window sensor.
Line 218: Line 256:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast blink for 8 seconds and then slow blink for 3 seconds when you press the Action Button again.
+
#If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast flash for '''8''' seconds and then slow flash for '''3''' seconds when you press the Action Button again.
#If the removal was unsuccessful, the Status LED will fast blink for 2 seconds and then be solid for 2 seconds when you press the Action Button, repeat the above steps.
+
#If the removal was unsuccessful, the Status LED will fast flash for '''2''' seconds and then be solid for '''2''' seconds when you press the Action Button, repeat the above steps.
  
 
<hr />
 
<hr />
Line 236: Line 274:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once to include the door/window sensor.
 
#Press the Action Button once to include the door/window sensor.
Line 270: Line 308:
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
 
#Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
#The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the will be blinking while awake.
+
#The sensor will now stay awake for '''10''' minutes to receive network instructions. The LED on the will be flashing while awake.
#*Note: The DSB04100 sensor can only be taught to communicate to devices within it’s own network.
+
#*Note: The DSB04100 sensor can only be taught to communicate to devices within its own network.
#*If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
+
#*If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for '''5''' seconds.
#*If the sensor was successfully included in the Z-Wave network, the LED will blink instead of staying solid.
+
#*If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 297: Line 335:
 
|<div style="text-align: center;">'''<big>ZW062</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW062</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
|}
  
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and release.
+
#Press and hold the Action Button for '''20''' seconds and release.
#Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking to confirm a success.
+
#Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#Press the Z-Wave Button on the Garage Door Controller.
#The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful inclusion.
+
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 318: Line 356:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#Press the Z-Wave Button on the Garage Door Controller.
#The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful exclusion.
+
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful exclusion.
#The Network LED on the Garage Door Controller should now be blinking slowly to indicate it is ready to be paired to a new network.
+
#The Network LED on the Garage Door Controller should now be flashing slowly to indicate it is ready to be paired to a new network.
  
 
<hr />
 
<hr />
Line 333: Line 371:
 
|<div style="text-align: center;">'''<big>ZW097</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW097</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear. If linking was unsuccessful, the LED will continue to blink if you tap its button.
+
#If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds, then disappear.
 +
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 351: Line 390:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
+
#If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
 +
#If unlinking was not successful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
  
 
<hr />
 
<hr />
Line 368: Line 408:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 10 seconds.
+
#Press and hold the Action Button for '''10''' seconds.
#If successful, the LED on the HEM should begin to blink slowly.
+
#If successful, the LED on the HEM should begin to flash slowly.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
 
#Remove the screw from the back of your Reader and open the battery cover.
 
#Remove the screw from the back of your Reader and open the battery cover.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for 1 second. If the linking was unsuccessful the light will blink after pressing your meter’s Action Button.
+
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for '''1''' second. If the linking was unsuccessful the light will flash after pressing your meter’s Action Button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 384: Line 424:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button (small black button under the battery tray) on your reader.If your Reader has been successfully removed from your network its light will blink for 1 second. If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
+
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully removed from your network, its light will flash for '''1''' second.
 +
#If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
  
 
----
 
----
Line 398: Line 439:
 
|<div style="text-align: center;">'''<big>ZW095</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW095</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 10 seconds.
+
#Press and hold the Action Button for '''10''' seconds.
#If successful, the LED on the HEM should begin to blink slowly.
+
#If successful, the LED on the HEM should begin to flash slowly.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to blink.
+
#Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to flash.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 415: Line 456:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will blink. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.
+
#Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will flash. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.
  
 
----
 
----
Line 429: Line 470:
 
|<div style="text-align: center;">'''<big>ZW098</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW098</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
Line 436: Line 477:
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch ON. LED Bulb’s green LED will blink to indicate that it is looking for a Z-Wave network to connect to.
+
#With LED Bulb in its fitting, wait '''2''' seconds. Now toggle your wall switch ON. LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
 
#After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
 
#After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
  
Line 447: Line 488:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Turn LED Bulb’s wall switch on.
 
#Turn LED Bulb’s wall switch on.
#Toggle LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if successful, the orange LED will be solid for 2 seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
+
#Toggle LED Bulb’s wall switch off, on, off, on, off, on within '''2''' seconds. The LED should flash orange, and if successful, the orange LED will be solid for '''2''' seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
#To confirm successful removal its color will change to orange for 2 seconds before changing to white. If removal was unsuccessful, LED Bulb will blink orange for 3 seconds before changing to red for 2 seconds.
+
#To confirm successful removal its color will change to orange for '''2''' seconds before changing to white. If removal was unsuccessful, LED Bulb will flash orange for '''3''' seconds before changing to red for '''2''' seconds.
  
 
----
 
----
Line 462: Line 503:
 
|<div style="text-align: center;">'''<big>ZWA002</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA002</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between 0.5 - 2 seconds per re-power.
+
#Toggle LED Bulb's wall switch '''6''' times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
#If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.
+
#If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white '''3''' times to indicate a successful factory reset.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to 10 seconds.
+
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to '''10''' seconds.
#After successfully connecting to your network, LED Bulb will flash green -> white color for 3 seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.
+
#After successfully connecting to your network, LED Bulb will flash green -> white color for '''3''' seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for '''3''' seconds.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 481: Line 522:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between 0.5 - 2 seconds per cycle.
+
#Toggle LED Bulb’s wall switch '''3''' times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
#LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for 3 seconds.
+
#LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for '''3''' seconds.
  
 
----
 
----
Line 496: Line 537:
 
|<div style="text-align: center;">'''<big>ZWA001</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between 0.5 - 2 seconds per re-power.
+
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
 
#If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
 
#If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will blink 2x times to indicate that it is looking for a Z-Wave network to connect to.
+
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will flash '''2''' times to indicate that it is looking for a Z-Wave network to connect to.
#After successfully connecting to your network, LED Bulb will blink off then on in about half a second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
+
#After successfully connecting to your network, LED Bulb will flash off then on in about '''0.5''' second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 515: Line 556:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between 0.5 - 2 seconds per cycle.
+
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
#LED Bulb 6 if successful will flash once, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
+
#LED Bulb 6 if successful will flash once, dim to 5% for '''5''' seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
  
 
----
 
----
Line 534: Line 575:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Hold the Z-Wave button for 30 seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for 30 seconds).
+
#Hold the Z-Wave button for '''30''' seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for '''30''' seconds).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
 
#Connect Micro Smart Dimmer to an AC‐input power source.
 
#Connect Micro Smart Dimmer to an AC‐input power source.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z‐Wave button.
 
#Press the Z‐Wave button.
Line 572: Line 613:
  
 
#Connect Micro Motor Controller to an AC‐input power source.
 
#Connect Micro Motor Controller to an AC‐input power source.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Micro Motor Controller.
 
#Press the Action Button on your Micro Motor Controller.
#If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
+
#If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
#If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
+
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
  
Line 583: Line 624:
  
 
#Connect Micro Motor Controller to an AC‐input power source.
 
#Connect Micro Motor Controller to an AC‐input power source.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#Press the Include button on your Minimote.
 
#Press the Include button on your Minimote.
 
#Press the Action Button on your Micro Motor Controller.
 
#Press the Action Button on your Micro Motor Controller.
#If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
+
#If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
#If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
+
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press any button on your Minimote to take it out of inclusion mode.
 
#Press any button on your Minimote to take it out of inclusion mode.
  
Line 598: Line 639:
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Micro Motor Controller.
 
#Press the Action Button on your Micro Motor Controller.
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
+
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
#If the removal was unsuccessful, the Network LED will not blink.
+
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
  
Line 609: Line 650:
 
#Press the Remove Button on your Minimote.
 
#Press the Remove Button on your Minimote.
 
#Press the Action Button on your Micro Motor Controller.
 
#Press the Action Button on your Micro Motor Controller.
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
+
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
#If the removal was unsuccessful, the Network LED will not blink.
+
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press any button on your Minimote to take it out of removal mode.
 
#Press any button on your Minimote to take it out of removal mode.
  
Line 628: Line 669:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the button on the Micro Switch G2 for 20 seconds and then release it.
+
#Press and hold the button on the Micro Switch G2 for '''20''' seconds and then release it.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
 
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
Line 642: Line 683:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
+
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch '''6''' times (ON to OFF or OFF to ON).
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
  
Line 661: Line 702:
  
 
#Pull down the panel on the  Minimote
 
#Pull down the panel on the  Minimote
#Press and hold the bottom 2 buttons down. The Red and Blue LED will alternate faster and faster.
+
#Press and hold the bottom '''2''' buttons down. The Red and Blue LED will alternate faster and faster.
 
#When both Red and Blue LED become solid, you may let go.
 
#When both Red and Blue LED become solid, you may let go.
  
 
'''Include a device''' '''from the Z-Wave Network'''
 
'''Include a device''' '''from the Z-Wave Network'''
  
#Tap the Inclusion (+) button, LED should be blinking blue
+
#Tap the Inclusion (+) button, LED should be flashing blue
 
#Tap the button on the device you want to add
 
#Tap the button on the device you want to add
 
#After the LED stops flashing rapidly, tap any button to get out of inclusion mode
 
#After the LED stops flashing rapidly, tap any button to get out of inclusion mode
Line 672: Line 713:
 
'''Exclusion a device from the Z-Wave Network'''
 
'''Exclusion a device from the Z-Wave Network'''
  
#Tap the Exclusion (-) button, LED should blink red
+
#Tap the Exclusion (-) button, LED should flash red
 
#Tap button on the device you want to remove
 
#Tap button on the device you want to remove
 
#After LED stops flashing rapidly, tap any button to get out of the exclusion mode
 
#After LED stops flashing rapidly, tap any button to get out of the exclusion mode
Line 691: Line 732:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold Multisensor Gen5 Action button (For 20 seconds)
+
#Press and hold Multisensor Gen5 Action button (For '''20''' seconds)
#The LED of the Multisensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
+
#The LED of the Multisensor Gen5 will flash faster and faster. At '''20''' seconds, the LED should become solid for '''1-2''' seconds to confirm factory reset.
 
#Release the Multisensor Gen5 Action Button.
 
#Release the Multisensor Gen5 Action Button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on your MultiSensor.
 
#Press the Z-Wave Button on your MultiSensor.
 
#You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
 
#You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
#If the LED blinks when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
+
#If the LED flashes when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 709: Line 750:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on your MultiSensor.
 
#Press the Z-Wave Button on your MultiSensor.
#If your MultiSensor has been successfully removed from your network, its LED will blink when you press the Z-wave Button.
+
#If your MultiSensor has been successfully removed from your network, its LED will flash when you press the Z-wave Button.
 
#If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.
 
#If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.
  
Line 724: Line 765:
 
|<div style="text-align: center;">'''<big>ZW100</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW100</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
+
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
+
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your MultiSensor. The LED on Multisensor will blink Green rapidly, followed by a solid Green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
+
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash Green rapidly, followed by a solid Green LED for '''1''' second for a successful inclusion, or a solid red LED for '''1''' second for a failed inclusion.
 
#You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
 
#You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
#If the green LED blinks when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
+
#If the green LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 744: Line 785:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
+
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
+
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
  
Line 763: Line 804:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the NanoMote button for 20 seconds.
+
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#The LED will change from: Orange > Green > Red > Pink > Red
#Release the button on the second Red LED status. It will remain red for 2 seconds
+
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
#Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
+
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Double click the NanoMote button, the LED will blink rapidly with a white color.
+
#Double click the NanoMote button, the LED will flash rapidly with a white color.
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
+
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
#If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
+
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
#*If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
+
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 800: Line 841:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the NanoMote button for 20 seconds.
+
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#The LED will change from: Orange > Green > Red > Pink > Red
#Release the button on the second Red LED status. It will remain red for 2 seconds
+
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
#Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
+
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Double click the NanoMote button (can be any button), the LED will blink rapidly with a white color.
+
#Double click the NanoMote button (can be any button), the LED will flash rapidly with a white color.
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
+
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
#*If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
+
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
 +
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 837: Line 879:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will blink to indicate the Nano Dimmer is entering into pairing mode.
+
#Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into pairing mode.
 
#If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
 
#If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
#If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.
+
#If the pairing was unsuccessful, the red LED will be on for '''2''' seconds and then remain a colorful gradient, repeat the steps above.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 853: Line 895:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 871: Line 913:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#Press the Action Button once on the Nano Switch.
#If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
+
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 886: Line 928:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 904: Line 946:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#Press the Action Button once on the Nano Switch.
#If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
+
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 919: Line 961:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 941: Line 983:
 
'''Join the Z-Wave Network''' '''(Z-Stick)'''
 
'''Join the Z-Wave Network''' '''(Z-Stick)'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Z-Stick.
#If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
+
#If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
#If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
+
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
  
 
'''Join the Z-Wave Network''' '''(Minimote)'''
 
'''Join the Z-Wave Network''' '''(Minimote)'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#Press the Include button on your Minimote.
 
#Press the Include button on your Minimote.
#If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
+
#If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
#If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
+
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press any button on your Minimote to take it out of inclusion mode.
 
#Press any button on your Minimote to take it out of inclusion mode.
  
Line 963: Line 1,005:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Z-Stick.
#If your Range Extender has been successfully removed from your network, its Network LED will blink.
+
#If your Range Extender has been successfully removed from your network, its Network LED will flash.
#If the removal was unsuccessful, the Network LED will not blink.
+
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
  
Line 973: Line 1,015:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Remove Button on your Minimote.
 
#Press the Remove Button on your Minimote.
#If your Range Extender has been successfully removed from your network, its Network LED will blink.
+
#If your Range Extender has been successfully removed from your network, its Network LED will flash.
#If the removal was unsuccessful, the Network LED will not blink.
+
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press any button on your Minimote to take it out of removal mode.
 
#Press any button on your Minimote to take it out of removal mode.
  
Line 989: Line 1,031:
 
|<div style="text-align: center;">'''<big>ZW117</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW117</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Z-Wave Button for 20 seconds to completely factory reset your Range Extender 6.
+
#Press and hold the Z-Wave Button for '''20''' seconds to completely factory reset your Range Extender 6.
#During the time that you are holding your Range Extender 6 action button down, the LED will blink through these colors: Yellow (at 2 seconds) > Purple (at 5 seconds) > Red for 8 seconds (initializing factory reset) > Green for 20 seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
+
#During the time that you are holding your Range Extender 6 action button down, the LED will flash through these colors: Yellow (at '''2''' seconds) > Purple (at '''5''' seconds) > Red for '''8''' seconds (initializing factory reset) > Green for '''20''' seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
#You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will blink green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
+
#Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will flash green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
#If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for 2 seconds then turn off. If the adding was unsuccessful, the red LED will be on for 2 seconds and then remain colorful gradient status, repeat the steps above.
+
#If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for '''2''' seconds then turn off. If the adding was unsuccessful, the red LED will be on for '''2''' seconds and then remain colorful gradient status, repeat the steps above.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,024: Line 1,066:
 
|<div style="text-align: center;">'''<big>ZW089</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW089</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it. Your sensor will now be reset to its original settings
+
#Press and hold the Action Button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear.
+
#Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds then disappear.
#If linking was unsuccessful, the LED will continue to blink if you tap its button.
+
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,041: Line 1,083:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time.
+
#Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
#If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
+
#If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
  
 
<hr />
 
<hr />
Line 1,059: Line 1,101:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button for 20 seconds
+
#Press and hold the Action button for '''20''' seconds
#At 8 seconds, the Siren will sound for 1 second, then stop
+
#At 8 seconds, the Siren will sound for '''1''' second, then stop
#The LED will continue to blink faster and faster and then will then turn solid for 2 seconds to indicate a successful factory reset
+
#The LED will continue to flash faster and faster and then will then turn solid for '''2''' seconds to indicate a successful factory reset
 
#You may let go of its Action button, and the Siren Gen5 factory reset is complete.
 
#You may let go of its Action button, and the Siren Gen5 factory reset is complete.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your Siren Gen5, and its LED will blink rapidly to indicate that it is communicating.
+
#Press the Action Button on your Siren Gen5, and its LED will flash rapidly to indicate that it is communicating.
#If your Siren has been successfully linked to your network, its LED will become solid for 2 seconds, then stop.
+
#If your Siren has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop.
#If linking was unsuccessful, the LED will blink when you tap its button.
+
#If linking was unsuccessful, the LED will flash when you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,078: Line 1,120:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Siren.
 
#Press the Action Button on your Siren.
#If your Siren has been successfully unlinked from your network, its LED will begin to blink.
+
#If your Siren has been successfully unlinked from your network, its LED will begin to flash.
  
 
<hr />
 
<hr />
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,090: Line 1,131:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Switch 6</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren 6</big>'''</div>
|<div style="text-align: center;">'''<big>ZW096</big>'''</div>
+
|<div style="text-align: center;">'''<big>ZW164-A</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds.
+
#Press and hold the Action button for '''20''' seconds
#The LED will change between these colors: Yellow > Purple > Red (blinks faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
+
#Within '''2-5''' seconds, the test siren sound will run, then stop after '''5''' seconds has elapsed.
#When the LED changes to Green state, you may let go of the action button.
+
#From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
#When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.
+
#After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 +
#With the LED pulsing, release the Action button, and the Siren 6 will be reset to factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#Power Siren 6 through the provided power adapter.
 +
#Ensure that Siren 6 LED is flashing slowly.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your Switch once and the LED will flash a green LED.
+
#Quickly tap the Siren 6 Action Button once.
#If your switch has been successfully linked to your network, its LED will become solid green for 2 seconds.
+
#If Siren 6 has successfully joined your Z-Wave network, the LED will emit a solid color for '''30''' seconds, then turn off.
#If linking was unsuccessful, the LED will return to a rainbow gradient.
+
#If the Siren 6 failed to pair, the LED will continue to blink slowly.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,114: Line 1,158:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on your Switch.
+
#Press the Action Button '''6''' times within '''2''' seconds .
#If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
+
#If your Siren 6 has been successfully excluded from the Z-Wave network, its LED will begin to flash slowly which indicates that it is ready to be paired again.
#If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.
 
  
 
<hr />
 
<hr />
Line 1,128: Line 1,171:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
|<div style="text-align: center;">'''<big>TriSensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smart Switch 6</big>'''</div>
|<div style="text-align: center;">'''<big>ZWA005</big>'''</div>
+
|<div style="text-align: center;">'''<big>ZW096 / ZW110</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 15 seconds.
+
#Press and hold the Action Button for '''20''' seconds.
 +
#The LED will change between these colors: Yellow > Purple > Red (flashs faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
 +
#When the LED changes to Green state, you may let go of the action button.
 +
#When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.
 +
 
 +
'''Join the Z-Wave Network'''
 +
 
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press the Action Button on your Switch once and the LED will flash a green LED.
 +
#If your switch has been successfully linked to your network, its LED will become solid green for '''2''' seconds.
 +
#If linking was unsuccessful, the LED will return to a rainbow gradient.
 +
 
 +
'''Exclusion from the Z-Wave Network'''
 +
 
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Action Button on your Switch.
 +
#If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
 +
#If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.
 +
 
 +
<hr />
 +
 
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 +
|<div style="text-align: center;">'''<big>TriSensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>ZWA005</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 
 +
#Press and hold the Action Button for '''15''' seconds.
 
#The red LED flashes to confirm a successful factory reset.
 
#The red LED flashes to confirm a successful factory reset.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your sensor once.
 
#Press the Action Button on your sensor once.
#The LED will turn yellow LED for 10 seconds.
+
#The LED will turn yellow LED for '''10''' seconds.
 
#If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
 
#If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
  
Line 1,151: Line 1,232:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your sensor.
 
#Press the Action Button on your sensor.
#The LED will turn purple for 2 seconds, and then white when exclusion is successful.
+
#The LED will turn purple for '''2''' seconds, and then white when exclusion is successful.
  
 
<hr />
 
<hr />
Line 1,169: Line 1,250:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button (20 seconds).
+
#Press and hold the Action button for '''20''' seconds.
#The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
+
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
#Let go of the Action Button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#Press the Action Button once on WallMote Quad to include it.
#The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
+
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,186: Line 1,267:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#Press the Action Button on your WallMote Quad.
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
+
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 +
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
  
 
<hr />
 
<hr />
Line 1,203: Line 1,285:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button (20 seconds).
+
#Press and hold the Action button for '''20''' seconds.
#The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
+
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
#Let go of the Action Button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#Press the Action Button once on WallMote Quad to include it.
#The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
+
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,220: Line 1,302:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#Press the Action Button on your WallMote Quad.
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
+
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 +
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
  
 
<hr />
 
<hr />
  
=='''<big>August</big>'''==
+
=='''<big>Alfred</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,232: Line 1,315:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>August</big>'''</div>
+
|<div style="text-align: center;">'''<big>Alfred</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Lock Pro</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smart Lock</big>'''</div>
|<div style="text-align: center;">'''<big>ASL-03</big>'''</div>
+
|<div style="text-align: center;">'''<big>DB2 / DB2-B</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#You must have your lock first connected to the August App
+
#Open the door and keep the lock bolt in the unlock position.
#Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
+
#Open the battery box to access the reset button.
#*My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
+
#Using a pointed object, press and hold the reset button.
#*My Hub is No Longer Working - use this mode to RESET the Device.
+
#Keep the reset button held down while removing and replacing one of the batteries.
#Select the '''My Hub is No Longer Working''' option and then select '''Reset Z-Wave Device'''.
+
#Keep holding the reset button down until you hear the voice guidance.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#You must have your lock first connected to the August App
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Touch the lock screen with your hand to activate it.
 +
#Press * twice, followed by your master PIN code and #
 +
#Digits 1-8 on the keypad should lightup in response.
 +
#Enter '''8''', followed by '''1''' to put the lock into inclusion mode.
 +
#*'''NOTE:'''  It is recommended that you delete all user codes from the lock if any are previously existing and use Hubitat Elevation™ Lock Code Manager to program the lock.
 +
 
 +
'''Exclusion from the Z-Wave Network'''
 +
 
 +
#You must have your lock first connected to the August App
 +
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Touch the lock screen with your hand to activate it.
 +
#Press * twice, followed by your master PIN code and #
 +
#Digits 1-8 on the keypad should lightup in response.
 +
#Enter '''8''', followed by '''2''' to put the lock into exclusion mode.
 +
 
 +
<hr />
 +
 
 +
=='''<big>August</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>August</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Smart Lock Pro</big>'''</div>
 +
|<div style="text-align: center;">'''<big>ASL-03</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 
 +
#You must have your lock first connected to the August App
 +
#Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
 +
#*My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
 +
#*My Hub is No Longer Working - use this mode to RESET the Device.
 +
#Select the '''My Hub is No Longer Working''' option and then select '''Reset Z-Wave Device'''.
 +
 
 +
'''Join the Z-Wave Network'''
 +
 
 +
#You must have your lock first connected to the August App
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#On the August App, go into Lock Settings and door for Z-Wave Settings.
 
#On the August App, go into Lock Settings and door for Z-Wave Settings.
Line 1,283: Line 1,410:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,297: Line 1,424:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
Line 1,314: Line 1,441:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,328: Line 1,455:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
Line 1,347: Line 1,474:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,361: Line 1,488:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
  
=='''<big>Centralite</big>'''==
+
=='''<big>BOSCH</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,373: Line 1,500:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
+
|<div style="text-align: center;">'''<big>BOSCH</big>'''</div>
|<div style="text-align: center;">'''<big>Pearl Thermostat</big>'''</div>
+
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
|<div style="text-align: center;">'''<big>3000-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>ISW-ZPR1-WP13</big>'''</div>
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
+
#Unlock the battery cover and slide it upwards to remove.
#The device will then factory reset itself and begin looking for an open network to join.
+
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 +
#Wait at least '''4''' seconds, but do not release the tamper switch.
 +
#Keep the tamper switch engaged while you reinsert both batteries.
 +
#Release the tamper switch. The device is now reset to factory default settings.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
  
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
+
#Unlock the battery cover and slide it upwards to remove.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
+
#*See Discovering your devices for detail instructions.
#The device will then factory reset itself and begin looking for an open network to join.
+
#Remove both batteries for at least '''10''' seconds.
 +
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
 +
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
 +
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove.'''
+
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
  
<hr />
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,402: Line 1,534:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
+
|<div style="text-align: center;">'''<big>BOSCH</big>'''</div>
|<div style="text-align: center;">'''<big>3-Series Smart Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
|<div style="text-align: center;">'''<big>3200-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>ISW-ZDL1-WP11G</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Unplug any devices from the module and unplug from the wall.
+
#Unlock the battery cover and slide it upwards to remove.
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
+
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 +
#Wait at least '''4''' seconds, but do not release the tamper switch.
 +
#Keep the tamper switch engaged while you reinsert both batteries.
 +
#Release the tamper switch. The device is now reset to factory default settings.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
  
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
+
#Unlock the battery cover and slide it upwards to remove.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
#Unplug any devices from the module and unplug from the wall.
+
#*See Discovering your devices for detail instructions.
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
+
#Remove both batteries for at least '''10''' seconds.
 +
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
 +
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
 +
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove.'''
+
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
  
<hr />
+
=='''<big>Centralite</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,432: Line 1,570:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>3-Series Door & Window Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Pearl Thermostat</big>'''</div>
|<div style="text-align: center;">'''<big>3300-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>3000-G</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Slide the sensor off the mount, remove cover, and remove battery.
+
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
#While holding down the reset button, reinsert battery to factory reset the device.
+
#The device will then factory reset itself and begin looking for an open network to join.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 1,445: Line 1,583:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
 +
#The device will then factory reset itself and begin looking for an open network to join.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,460: Line 1,599:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>3-Series Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>3-Series Smart Outlet</big>'''</div>
|<div style="text-align: center;">'''<big>3305-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>3200-G</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Slide the sensor off the mount, remove cover, and remove battery.
+
#Unplug any devices from the module and unplug from the wall.
#While holding down the reset button, reinsert battery to factory reset the device.
+
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 1,473: Line 1,612:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Unplug any devices from the module and unplug from the wall.
 +
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,488: Line 1,628:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>3-Series Micro Door Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>3-Series Door & Window Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>3323-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>3300-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
Line 1,501: Line 1,641:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Slide the sensor off the mount, remove cover, and remove battery.
 +
#While holding down the reset button, reinsert battery to factory reset the device.
  
 
<hr />
 
<hr />
Line 1,516: Line 1,658:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>3-Series Micro Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>3-Series Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>3328-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>3305-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
Line 1,529: Line 1,671:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Slide the sensor off the mount, remove cover, and remove battery.
 +
#While holding down the reset button, reinsert battery to factory reset the device.
  
 
<hr />
 
<hr />
Line 1,544: Line 1,688:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>4-Series Smart Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>3-Series Micro Door Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>4200-C</big>'''</div>
+
|<div style="text-align: center;">'''<big>3323-G</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Unplug any devices from the module and unplug from the wall.
+
#Slide the sensor off the mount, remove cover, and remove battery.
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
+
#While holding down the reset button, reinsert battery to factory reset the device.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 1,557: Line 1,701:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Unplug any devices from the module and unplug from the wall.
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
#After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green
 
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Slide the sensor off the mount, remove cover, and remove battery.
 +
#While holding down the reset button, reinsert battery to factory reset the device.
  
 
<hr />
 
<hr />
 
=='''<big>CREE</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>CREE</big>'''</div>
+
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>Connected LED Bulbs</big>'''</div>
+
|<div style="text-align: center;">'''<big>3-Series Micro Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
+
|<div style="text-align: center;">'''<big>3328-G</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
+
#Slide the sensor off the mount, remove cover, and remove battery.
#The bulb will blink once, indicating it is reset and ready for pairing
+
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
'''Factory Reset (Alternate Method)'''
 
 
 
*'''''Method 1 - Use a Philips Hue Dimmer Switch'''''
 
 
 
#Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
 
#Hold the remote within 4 inches of the bulb.
 
#Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts blinking on and off.
 
#If the bulb stopped blinking (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) blinked green - your bulb is reset.
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 
 
 
*'''''Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)'''''
 
 
 
#Hold the remote within 4 inches of the bulb.
 
#Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
 
#The bulb should blink on and off
 
#The green LED on the remote should come on and may blink a few times.
 
#Continue to hold both buttons on the remote until the green LED goes off completely.
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 1,606: Line 1,731:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
#The bulb will blink once, indicating it is reset and ready for pairing
 
 
 
'''Join the Zigbee Network''' '''(Alternate Method)'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#See '''Factory Reset (Alternate Method)''' above to reset the bulb and put it into pairing mode.
 
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Slide the sensor off the mount, remove cover, and remove battery.
 +
#While holding down the reset button, reinsert battery to factory reset the device.
  
 
<hr />
 
<hr />
=='''<big>Dome</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,628: Line 1,747:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
+
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>4-Series Smart Outlet</big>'''</div>
|<div style="text-align: center;">'''<big>DMWD1</big>'''</div>
+
|<div style="text-align: center;">'''<big>4200-C</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Open the Cover and make sure the Door/Window Sensor is powered.
+
#Unplug any devices from the module and unplug from the wall.
#Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
+
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  
'''Join the Z-Wave Network'''
+
'''Join the Zigbee Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
+
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the Cover of the Door/Window Sensor.
+
#Unplug any devices from the module and unplug from the wall.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 +
#After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green
  
'''Exclusion from the Z-Wave Network'''
+
'''Leaving the Zigbee Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove'''
+
#From the device's details page, select '''Remove Device''', then '''Remove.'''
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Unplug any devices from the module and unplug from the wall.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
#Remove the Cover of the Door/Window Sensor.
 
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
 
  
 
<hr />
 
<hr />
 +
 +
=='''<big>CREE</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Device</div>
|<div style="text-align: center;">Product Number</div>
 
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
+
|<div style="text-align: center;">'''<big>CREE</big>'''</div>
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Connected LED Bulbs</big>'''</div>
|<div style="text-align: center;">'''<big>DMDP1</big>'''</div>
+
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
+
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
#Wait for 5 seconds.
+
#The bulb will flash once, indicating it is reset and ready for pairing
#Move the Magnet and Sensor Base in and out of the closed position 6 times.
 
#The LED indicator will light up red for five seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
 
  
'''Join the Z-Wave Network'''
+
'''Factory Reset (Alternate Method)'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
*'''''Method 1 - Use a Philips Hue Dimmer Switch'''''
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
+
 
#Remove the Sensor Cover and the LED indicator will start blinking yellow.
+
#Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
#Press the Button quickly 3 times in a row.
+
#Hold the remote within '''4''' inches of the bulb.
#The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green three times then blink red until the cover is replaced.
+
#Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about '''10''' seconds, until the bulb starts flashing on and off.
 +
#If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
 +
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 +
 
 +
*'''''Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)'''''
 +
 
 +
#Hold the remote within '''4''' inches of the bulb.
 +
#Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
 +
#The bulb should flash on and off
 +
#The green LED on the remote should come on and may flash a few times.
 +
#Continue to hold both buttons on the remote until the green LED goes off completely.
 +
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 +
 
 +
'''Join the Zigbee Network'''
 +
 
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
 +
#The bulb will flash once, indicating it is reset and ready for pairing
  
'''Exclusion from the Z-Wave Network'''
+
'''Join the Zigbee Network''' '''(Alternate Method)'''
  
#From the device's details page, select '''Remove Device''', then '''Remove'''
+
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the SENSOR COVER and the LED indicator will start blinking red.
+
#See '''Factory Reset (Alternate Method)''' above to reset the bulb and put it into pairing mode.
#Press the Button quickly 3 times in a row.
+
 
#The LED Indicator will flash green three times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
+
'''Leaving the Zigbee Network'''
 +
 
 +
#From the device's details page, select '''Remove Device''', then '''Remove.'''
  
 
<hr />
 
<hr />
 +
=='''<big>Dome</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,699: Line 1,835:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>DMWS1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMWD1</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Open the Back Plate and make sure the Leak Sensor is powered.
+
#Open the Cover and make sure the Door/Window Sensor is powered.
#Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the cover of the Leak Sensor by twisting it apart.
+
#Remove the Cover of the Door/Window Sensor.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating inclusion.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,720: Line 1,856:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the cover of the Leak Sensor by twisting it apart.
+
#Remove the Cover of the Door/Window Sensor.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,732: Line 1,868:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>DMMS1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMDP1</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Remove the Cover and make sure the Motion Detector is powered.
+
#Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
#Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.
+
#Wait for '''5''' seconds.
 +
#Move the Magnet and Sensor Base in and out of the closed position '''6''' times.
 +
#The LED indicator will light up Red for '''5''' seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the cover of the Motion Detector by twisting it apart.
+
#Remove the Sensor Cover and the LED indicator will start flashing yellow.
#Press the Connect Button quickly 3 times in a row.
+
#Press the Button quickly '''3''' times in a row.
#The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green '''3''' times then flash red until the cover is replaced.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,754: Line 1,892:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
+
#Remove the SENSOR COVER and the LED indicator will start flashing red.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Button quickly '''3''' times in a row.
 +
#The LED Indicator will flash green '''3''' times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
  
 
<hr />
 
<hr />
Line 1,766: Line 1,905:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Mouser</big>'''</div>
+
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>DMMZ1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMWS1</big>'''</div>
|<div style="text-align: center;">'''<big>Mouse Trap</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
+
#Open the Back Plate and make sure the Leak Sensor is powered.
#Press and hold the CONNECT BUTTON for at least 10 seconds then release.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashs once, then release the button.
#A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
+
#Remove the cover of the Leak Sensor by twisting it apart.
#Press the CONNECT BUTTON quickly 3 times in a row.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating inclusion.
#The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,789: Line 1,926:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
+
#Remove the cover of the Leak Sensor by twisting it apart.
#Press the CONNECT BUTTON quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,801: Line 1,938:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>On/Off Plug-In Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>DMOF1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMMS1</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Plug in the On/Off Plug-In Switch.
+
#Remove the Cover and make sure the Motion Detector is powered.
#Hold the Connect Button for 10 seconds until the LED Indicator blinks once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#Remove the cover of the Motion Detector by twisting it apart.
 +
#Press the Connect Button quickly '''3''' times in a row.
 +
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,821: Line 1,960:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
+
#Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,833: Line 1,972:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Range Extender</big>'''</div>
+
|<div style="text-align: center;">'''<big>Mouser</big>'''</div>
|<div style="text-align: center;">'''<big>DMEX1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMMZ1</big>'''</div>
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
+
|<div style="text-align: center;">'''<big>Mouse Trap</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Hold the Button for 10 seconds until the LED blinks 10 times, then release the button
+
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 +
#Press and hold the CONNECT BUTTON for at least '''10''' seconds then release.
 +
#A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#For proper inclusion, install the Range Extender in the final location where it will be used.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash 5 times indicating successful inclusion.
+
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 +
#Press the CONNECT BUTTON quickly '''3''' times in a row.
 +
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,853: Line 1,995:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Button quickly 3 times in a row The LED will flash 5 times indicating successful exclusion.
+
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 +
#Press the CONNECT BUTTON quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,864: Line 2,007:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
+
|<div style="text-align: center;">'''<big>On/Off Plug-In Switch</big>'''</div>
|<div style="text-align: center;">'''<big>DMS01</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMOF1</big>'''</div>
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Open the Back Plate and make sure the Siren is powered.
+
#Plug in the On/Off Plug-In Switch.
#Hold the Connect Button for 10 seconds until the LED Ring blinks once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED Indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the Back Plate of the Siren.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
#Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful inclusion to the Z-Wave network.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,885: Line 2,027:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the Back Plate of the Siren.
+
#Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
#Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,897: Line 2,039:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Water Main Shut-Off</big>'''</div>
+
|<div style="text-align: center;">'''<big>Range Extender</big>'''</div>
|<div style="text-align: center;">'''<big>DMWV1</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMEX1</big>'''</div>
|<div style="text-align: center;">'''<big>Shutoff Valve</big>'''</div>
+
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the open/close button for at least 10 seconds then release.
+
#Hold the Button for '''10''' seconds until the LED flashes '''10''' times, then release the button
#The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#For proper inclusion, install the Range Extender in the final location where it will be used.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly 3 times in a row. The LED will stop blinking and stay on continuously upon successful inclusion.
+
#Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash '''5''' times indicating successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,917: Line 2,059:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.
+
#Press the Button quickly '''3''' times in a row The LED will flash '''5''' times indicating successful exclusion.
  
 
<hr />
 
<hr />
 
=='''<big>Dragon Tech</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,929: Line 2,069:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Dragon Tech</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Plug in Z-Wave Plus Dimmer Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
|<div style="text-align: center;">'''<big>PD-100</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMS01</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Unplug the PD-100 and anything the is plugged into it.
+
#Open the Back Plate and make sure the Siren is powered.
#Press and hold the button on the front of the PD-100
+
#Hold the Connect Button for '''10''' seconds until the LED Ring flashs once, then release the button.
#Plug the PD-100 in while still pressing the button
 
#After 3 seconds, release the button. If the button blinks, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the button on the front of the PD-100
+
#Remove the Back Plate of the Siren.
 +
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,952: Line 2,091:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the button on the front of the PD-100
+
#Remove the Back Plate of the Siren.
 +
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
 
==<big>'''Eaton''' '''(Cooper Wiring Devices)'''</big>==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,964: Line 2,102:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Eaton</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
|<div style="text-align: center;">'''<big>Wireless Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Main Shut-Off</big>'''</div>
|<div style="text-align: center;">'''<big>RF9540</big>'''</div>
+
|<div style="text-align: center;">'''<big>DMWV1</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Shutoff Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
+
#Press and hold the open/close button for at least '''10''' seconds then release.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Cooper Wiring Devices Z-Wave device has a blue LED, which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the device switch one time to include it in the network. The LED will stop blinking, indicating the dimmer has been successfully included in the Z-Wave network.
+
#Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly '''3''' times in a row. The LED will stop flashing and stay on continuously upon successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,988: Line 2,123:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.
+
#When prompted, press the “open/close” button on the Shut-Off quickly '''3''' times in a row.
  
 
<hr />
 
<hr />
=='''<big>Ecolink</big>'''==
+
 
 +
=='''<big>Dragon Tech</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,999: Line 2,135:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dragon Tech</big>'''</div>
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug in Z-Wave Plus Dimmer Switch</big>'''</div>
|<div style="text-align: center;">'''<big>DWZWAVE2.5-ECO</big>'''</div>
+
|<div style="text-align: center;">'''<big>PD-100</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
+
#Unplug the PD-100 and anything the is plugged into it.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Press and hold the button on the front of the PD-100
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#Plug the PD-100 in while still pressing the button
#Remove the battery for at least 5 seconds, then reinstall it.
+
#After '''3''' seconds, release the button. If the button flashes, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the button on the front of the PD-100
#When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,024: Line 2,158:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the button on the front of the PD-100
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
  
 
<hr />
 
<hr />
 +
 +
==<big>'''Eaton''' '''(Cooper Wiring Devices)'''</big>==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,035: Line 2,170:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
+
|<div style="text-align: center;">'''<big>Eaton</big>'''</div>
|<div style="text-align: center;">'''<big>Flood/Freeze Sensor</big>''' </div>
+
|<div style="text-align: center;">'''<big>Wireless Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>FLF-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>RF9540</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#The Flood Freeze sensor factory defaults on network exclusion
+
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for 1 second, then reinstall it.
+
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#Cooper Wiring Devices Z-Wave device has a blue LED, which will flash when the device is not included in a Z-Wave network. The LED stops flashing when the device is in a network.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 10 seconds, then reinstall it.
+
#Press the device switch once to include it in the network. The LED will stop flashing, indicating the dimmer has been successfully included in the Z-Wave network.
#If the LED starts blinking continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.
 
#If after 5 seconds the LED is not blinking, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,060: Line 2,194:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the Flood Freeze case and remove the battery for 1 second.
+
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
#Replace the battery and the device should be removed from the Z-Wave network.
 
  
 
<hr />
 
<hr />
 +
=='''<big>Ecolink</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,072: Line 2,206:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor with Pet Immunity</big>''' </div>
+
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>PIR-ZWAVE2.5</big>'''</div>
+
|<div style="text-align: center;">'''<big>DWZWAVE2.5-ECO</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
Line 2,081: Line 2,215:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#Re-attach the battery cover
+
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#Re-attach the battery cover and the device with enter inclusion mode
+
#When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,098: Line 2,230:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#Re-attach the battery cover and the device with enter exclusion mode
+
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
  
 
<hr />
 
<hr />
Line 2,111: Line 2,242:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
+
|<div style="text-align: center;">'''<big>Flood/Freeze Sensor</big>''' </div>
|<div style="text-align: center;">'''<big>SC-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>FLF-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
+
#The Flood Freeze sensor factory defaults on network exclusion
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
+
#Remove the battery for '''1''' second, then reinstall it.
#The LED on the front of the unit will turn off if successful exclusion from the network.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
+
#Remove the battery for at least '''10''' seconds, then reinstall it.
#The LED on the front of the unit will turn off if successful included in the network.
+
#If the LED starts flashing continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for '''10''' seconds if adding to a Z-Wave network fails.
 +
#If after '''5''' seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,135: Line 2,266:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
+
#Open the Flood Freeze case and remove the battery for '''1''' second.
#The LED on the front of the unit will turn off if successful exclusion from the network.
+
#Replace the battery and the device should be removed from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 2,147: Line 2,278:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>FireFighter</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor with Pet Immunity</big>''' </div>
|<div style="text-align: center;">'''<big>FF-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>PIR-ZWAVE2.5</big>'''</div>
|<div style="text-align: center;">'''<big>Smoke/CO Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 2,156: Line 2,287:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously
+
#Re-attach the battery cover
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#If the LED starts blinking continually, the sensor has not been added. Repeat the steps.
+
#Re-attach the battery cover and the device with enter inclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 +
#Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,171: Line 2,304:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously
+
#Re-attach the battery cover and the device with enter exclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
Line 2,183: Line 2,317:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
|<div style="text-align: center;">'''<big>DLS-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>SC-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 2,192: Line 2,326:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 +
#The LED on the front of the unit will turn off if successful exclusion from the network.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 
#The LED on the front of the unit will turn off if successful included in the network.
 
#The LED on the front of the unit will turn off if successful included in the network.
  
Line 2,206: Line 2,341:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 +
#The LED on the front of the unit will turn off if successful exclusion from the network.
  
 
<hr />
 
<hr />
Line 2,217: Line 2,353:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Switch Double Toggle</big>''' </div>
+
|<div style="text-align: center;">'''<big>FireFighter</big>'''</div>
|<div style="text-align: center;">'''<big>DTLS2-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>FF-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smoke/CO Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 2,226: Line 2,362:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 +
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
#The LED on the front of the unit will turn off if successful included in the network.
+
#If the LED starts flashing continually, the sensor has not been added. Repeat the steps.
 
+
 
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
  
Line 2,240: Line 2,377:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 +
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
  
 
<hr />
 
<hr />
Line 2,251: Line 2,389:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Switch Dual Rocker</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smart Switch</big>'''</div>
|<div style="text-align: center;">'''<big>DDLS2-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>DLS-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
Line 2,264: Line 2,402:
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#Press the inclusion / exclusion button on the Smart Switch.
#The LED on the front of the unit will turn off if successful included in the network.
+
#The LED on the front of the unit will turn off if successfully included in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,285: Line 2,423:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
+
|<div style="text-align: center;">'''<big>Smart Switch Double Toggle</big>''' </div>
|<div style="text-align: center;">'''<big>TILT-ZWAVE2</big>'''</div>
+
|<div style="text-align: center;">'''<big>DTLS2-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
Line 2,294: Line 2,432:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover and the device with enter inclusion mode
+
#The LED on the front of the unit will turn off if successful included in the network.
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,311: Line 2,446:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover and the device with enter exclusion mode
 
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
  
 
<hr />
 
<hr />
Line 2,324: Line 2,457:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
+
|<div style="text-align: center;">'''<big>Smart Switch Dual Rocker</big>'''</div>
|<div style="text-align: center;">'''<big>TILT-ZWAVE2.5</big>'''</div>
+
|<div style="text-align: center;">'''<big>DDLS2-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 2,333: Line 2,466:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover and the device with enter inclusion mode
+
#The LED on the front of the unit will turn off if successful included in the network.
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,350: Line 2,480:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Press the inclusion / exclusion button on the Smart Switch.
#Re-attach the battery cover and the device with enter exclusion mode
 
#The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
  
 
<hr />
 
<hr />
Line 2,363: Line 2,491:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Toggle Light Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
|<div style="text-align: center;">'''<big>TLS-ZWAVE5</big>'''</div>
+
|<div style="text-align: center;">'''<big>TILT-ZWAVE2</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
Line 2,372: Line 2,500:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 +
#Re-attach the battery cover
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
#The LED on the front of the unit will turn off if successful included in the network.
+
#Re-attach the battery cover and the device with enter inclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 +
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,386: Line 2,517:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion / exclusion button on the Smart Switch.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 +
#Re-attach the battery cover and the device with enter exclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
 
=='''<big>Enerwave</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,398: Line 2,529:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Enerwave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Ceiling Mounted PIR Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
|<div style="text-align: center;">'''<big>ZWN-BPC-Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>TILT-ZWAVE2.5</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.
+
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Remove the battery for at least '''5''' seconds, then reinstall it.
 +
#Re-attach the battery cover
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the inclusion/exclusion button on the sensor 3 times.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 +
#Re-attach the battery cover and the device with enter inclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 +
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,418: Line 2,556:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion/exclusion button on the sensor 3 times.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 +
#Re-attach the battery cover and the device with enter exclusion mode
 +
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
=='''<big>Everspring</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,429: Line 2,568:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
+
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
|<div style="text-align: center;">'''<big>Door/Window Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Toggle Light Switch</big>'''</div>
|<div style="text-align: center;">'''<big>HSM02</big>'''</div>
+
|<div style="text-align: center;">'''<big>TLS-ZWAVE5</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED will be steady on.
+
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
#Within 1 second, press and hold the tamper switch until LED is off.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
+
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the inclusion / exclusion button on the Smart Switch.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
+
#Press the inclusion / exclusion button on the Smart Switch.
 +
#The LED on the front of the unit will turn off if successful included in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,451: Line 2,592:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
+
#Press the inclusion / exclusion button on the Smart Switch.
  
 
<hr />
 
<hr />
 +
 +
=='''<big>Enerwave</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,461: Line 2,604:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
+
|<div style="text-align: center;">'''<big>Enerwave</big>'''</div>
|<div style="text-align: center;">'''<big>Flood Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Ceiling Mounted PIR Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>ST812</big>'''</div>
+
|<div style="text-align: center;">'''<big>ZWN-BPC-Plus</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press link key three times within 1.5 second. The sensor will beep each time the link key is pressed.
+
#To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor '''3''' times and hold for '''3''' seconds on the 3rd press.
#Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
 
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing link key three times within 1.5 second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
+
#Press the inclusion/exclusion button on the sensor '''3''' times.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,483: Line 2,624:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing link key three times within 1.5 second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
+
#Press the inclusion/exclusion button on the sensor '''3''' times.
  
 
<hr />
 
<hr />
 +
=='''<big>Everspring</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,494: Line 2,636:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
|<div style="text-align: center;">'''<big>PIR Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Door/Window Detector</big>'''</div>
|<div style="text-align: center;">'''<big>HSP02</big>'''</div>
+
|<div style="text-align: center;">'''<big>HSM02</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED will be steady on.
+
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
#Within 1 second, press and hold the tamper switch until LED is off.
+
#Within '''1''' second, press and hold the tamper switch until LED is off.
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,515: Line 2,657:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second will enter exclusion mode.
+
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
  
 
<hr />
 
<hr />
Line 2,526: Line 2,668:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
|<div style="text-align: center;">'''<big>Photoelectric Smoke Alarm</big>'''</div>
+
|<div style="text-align: center;">'''<big>Flood Detector</big>'''</div>
|<div style="text-align: center;">'''<big>SF-813</big>'''</div>
+
|<div style="text-align: center;">'''<big>ST812</big>'''</div>
|<div style="text-align: center;">'''<big>Smoke Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Press link key three times within '''1.5''' second. The sensor will beep each time the link key is pressed.
#Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
+
#Within '''1''' second, press and hold the link key. The sensor will long beep for '''5''' seconds. Keep holding the link key until the long beep stops.
#The LED will light for 5 seconds and the buzzer will sound for 5 seconds
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Pressing link key three times within '''1.5''' second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
#The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
 
#The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has joined the Z-Wave network.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,549: Line 2,689:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Pressing link key three times within '''1.5''' second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
#The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
 
#The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has been excluded from the Z-Wave network.
 
  
 
<hr />
 
<hr />
Line 2,562: Line 2,700:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
|<div style="text-align: center;">'''<big>Temperature/Humidity Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>PIR Detector</big>'''</div>
|<div style="text-align: center;">'''<big>SF-814</big>'''</div>
+
|<div style="text-align: center;">'''<big>HSP02</big>'''</div>
|<div style="text-align: center;">'''<big>Temperature Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
#Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
+
#Within '''1''' second, press and hold the tamper switch until LED is off.
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,583: Line 2,721:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode.
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
 
  
 
<hr />
 
<hr />
=='''<big>Evolve</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,595: Line 2,731:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Evolve</big>'''</div>
+
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
|<div style="text-align: center;">'''<big>Isolated Contact Fixture Module</big>'''</div>
+
|<div style="text-align: center;">'''<big>Photoelectric Smoke Alarm</big>'''</div>
|<div style="text-align: center;">'''<big>LFM-20</big>'''</div>
+
|<div style="text-align: center;">'''<big>SF-813</big>'''</div>
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smoke Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
+
#Press tamper switch three times within '''1.5''' second. The LED flashes and the buzzer sounds when the link key is pressed.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Within '''1''' second, press and hold the tamper switch for '''5''' seconds until the LED is off.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#The LED will light for '''5''' seconds and the buzzer will sound for '''5''' seconds
#Exclude the module by tapping the button three times, then press and hold for 10 seconds.
 
#*LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the button on the once to include it in the Z-Wave network.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
 +
#The detector will stay awake and remain in inclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
 +
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has joined the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,619: Line 2,755:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Exclude the module by tapping the button three times, then press and hold for 10 seconds.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
#*LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
+
#The detector will stay awake and remain in exclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
 +
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has been excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
 
=='''<big>Fibaro</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,632: Line 2,767:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
+
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
|<div style="text-align: center;">'''<big>Button</big>'''</div>
+
|<div style="text-align: center;">'''<big>Temperature/Humidity Detector</big>'''</div>
|<div style="text-align: center;">'''<big>FGPB-101</big>'''</div>
+
|<div style="text-align: center;">'''<big>SF-814</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Temperature Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Click the Button exactly five times.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
#Press and hold the Button for at least 5 seconds.
+
#Within '''1''' second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
 +
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Click the button at least 6 times.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
#Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
 
#Click the button 4 times to wake it up
 
#Watch the status in the device details page to confirm proper operation.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,656: Line 2,789:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Click the Button at least six times.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
#Wait for the removing process to end.
+
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
#The device will be excluded from the Z-Wave network.
 
  
 
<hr />
 
<hr />
 +
=='''<big>Evolve</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,668: Line 2,801:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
+
|<div style="text-align: center;">'''<big>Evolve</big>'''</div>
|<div style="text-align: center;">'''<big>Door/Window Sensor 2</big>'''</div>
+
|<div style="text-align: center;">'''<big>Isolated Contact Fixture Module</big>'''</div>
|<div style="text-align: center;">'''<big>FGDW-002</big>'''</div>
+
|<div style="text-align: center;">'''<big>LFM-20</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Open the cover and remove the battery.
+
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
#Install the battery while holding both TMP buttons.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
#The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
+
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Release one button when the LED indicator starts flashing quickly.
+
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
#Click the released button once to confirm initiation of the reset procedure.
+
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
#Wait a few seconds for a long blink of the LED indicator. '''Do not remove the battery'''.
 
#The LED indicator will blink 5 times quickly to confirm reset of the device.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press one of the TMP buttons quickly, three times in a row, '''while keeping other button is pressed'''.
+
#Press the button on the device once to include it in the Z-Wave network.
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,697: Line 2,825:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press one of the TMP buttons quickly, three times in a row, '''while keeping other button is pressed'''.
+
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
#The device will be excluded from the Z-Wave network.
+
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
  
 
<hr />
 
<hr />
 +
 +
=='''<big>Fibaro</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 2,709: Line 2,839:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Flood Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Button</big>'''</div>
|<div style="text-align: center;">'''<big>FGFS-101 FG3</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGPB-101</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Make sure the sensor is powered.
+
#Click the Button exactly five times.
#Press and hold the TMP button.
+
#Press and hold the Button for at least '''5''' seconds.
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
 
#Release the TMP button.
 
#Click the TMP button once to confirm selection.
 
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Removed the battery for 10 seconds, and re-install it
+
#Click the button at least '''6''' times.
#Wait for the inclusion process to end.
+
#Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
#Successful inclusion will be confirmed by Hubitat Elevation™
+
#Click the button '''4''' times to wake it up
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
  
Line 2,736: Line 2,862:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Click the Button at least '''6''' times.
 +
#Wait for the removing process to end.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,748: Line 2,875:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Flood Sensor ZW5</big>'''</div>
+
|<div style="text-align: center;">'''<big>Door/Window Sensor 2</big>'''</div>
|<div style="text-align: center;">'''<big>FGFS-101 ZW5</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGDW-002</big>'''</div>
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Make sure the sensor is powered.
+
#Open the cover and remove the battery.
#Press and hold the TMP button.
+
#Install the battery while holding both TMP buttons.
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
+
#The LED indicator will be flashing slowly for '''5''' seconds, but keep holding the buttons.
#Release the TMP button.
+
#Release one button when the LED indicator starts flashing quickly.
#Click the TMP button once to confirm selection.
+
#Click the released button once to confirm initiation of the reset procedure.
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
+
#Wait a few seconds for a long flash of the LED indicator. '''Do not remove the battery'''.
 +
#The LED indicator will flash '''5''' times quickly to confirm reset of the device.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 2,775: Line 2,903:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,787: Line 2,915:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>KeyFob</big>'''</div>
+
|<div style="text-align: center;">'''<big>Flood Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>FGKF-601 ZW5</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGFS-101 FG3</big>'''</div>
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Click '''O''' and '''<big>–</big>''' simultaneously.
+
#Make sure the sensor is powered.
#Click '''∆''' or '''X''' until LED is '''Yellow''' - reset the device.
+
#Press and hold the TMP button.
#Click '''<big>+</big>''' to confirm selection, or is you do not wish to reset at this time, click <big>'''–'''</big> to exit the menu.
+
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
#The LED will pulse '''Yellow''' twice to confirm the device has been reset.
+
#Release the TMP button.
 +
#Click the TMP button once to confirm selection.
 +
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#LED will pulse '''White''' during the adding process.
+
#Removed the battery for '''10''' seconds, and re-install it
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
#Successful adding will be confirmed by the Z-Wave controller’s message.
+
#Successful inclusion will be confirmed by Hubitat Elevation™
#Successful inclusion will be confirmed by Hubitat Elevation™ and the remote LED will be '''Green'''.
 
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
  
Line 2,813: Line 2,942:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Click '''O''' and '''<big>–</big>''' simultaneously.
+
#Press the TMP button quickly, '''3''' times in a row.
#Click '''∆''' or '''X''' until LED is '''Green.'''
 
#Click '''<big>+</big>''' to confirm selection.
 
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,827: Line 2,954:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor ZW5</big>'''</div>
+
|<div style="text-align: center;">'''<big>Flood Sensor ZW5</big>'''</div>
|<div style="text-align: center;">'''<big>FGMS-001 ZW5</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGFS-101 ZW5</big>'''</div>
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Open the cover
+
#Make sure the sensor is powered.
#Press and hold the B-button.
+
#Press and hold the TMP button.
#Wait for visual indicator to glow '''Yellow''' (2nd menu position).
+
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
#Release the '''B''' button and then briefly click the B-button to confirm selection
+
#Release the TMP button.
#After few seconds the device will be reset, which is signaled with the red, fading visual indicator color.
+
#Click the TMP button once to confirm selection.
 +
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the '''B''' button quickly, three times in a row.
+
#Press the TMP button quickly, '''3''' times in a row.
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 2,853: Line 2,981:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the '''B''' button quickly, three times in a row.
+
#Press the TMP button quickly, '''3''' times in a row.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,865: Line 2,993:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>KeyFob</big>'''</div>
|<div style="text-align: center;">'''<big>FGRGBW-101</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGKF-601 ZW5</big>'''</div>
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Disconnect the supply voltage.
+
#Click '''O''' and '''<big>–</big>''' simultaneously.
#Press and hold the '''B''' button located inside the RGBW Controllers casing.
+
#Click '''∆''' or '''X''' until LED is '''Yellow''' - reset the device.
#Connect the the supply voltage, while still holding the '''B''' button.
+
#Click '''<big>+</big>''' to confirm selection, or is you do not wish to reset at this time, click <big>''''''</big> to exit the menu.
#Release the '''B''' button.
+
#The LED will pulse '''Yellow''' twice to confirm the device has been reset.
#The '''B''' channel will turn on (blue channel).
 
#Disconnect  the power supply.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
('''Auto Inclusion''')
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
 
#Make sure the RGBW Controller is not connected to a supply.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Connect voltage supply to auto-include the RGBW Controller.
+
#LED will pulse '''White''' during the adding process.
#The RGBW Controller will be automatically recognized and included in the Z-Wave network.
+
#Wait for the inclusion process to end.
#Successful inclusion will be confirmed by Hubitat Elevation™
+
#Successful adding will be confirmed by the Z-Wave controller’s message.
 +
#Successful inclusion will be confirmed by Hubitat Elevation™ and the remote LED will be '''Green'''.
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
  
'''(Manual Inclusion''')
+
'''Exclusion from the Z-Wave Network'''
 
 
#Make sure the RGBW Controller is not connected to a supply.
 
#To disable auto-inclusion press the '''B''' button briefly, after re-connecting the RGBW Controller to its supply voltage.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
 
#The RGBW Controller will be recognized and included in the Z-Wave network.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
+
#Click '''O''' and '''<big>–</big>''' simultaneously.
 +
#Click '''∆''' or '''X''' until LED is '''Green.'''
 +
#Click '''<big>+</big>''' to confirm selection.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,918: Line 3,033:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Single Switch 2</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor ZW5</big>'''</div>
|<div style="text-align: center;">'''<big>FGS-213</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGMS-001 ZW5</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Switch off the mains voltage (disable the breaker).
+
#Open the cover
#Remove the Switch 2 from the wall switch box.
+
#Press and hold the B-button.
#Switch on the mains voltage.
+
#Wait for visual indicator to glow '''Yellow''' (2nd menu position).
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
+
#Release the '''B''' button and then briefly click the B-button to confirm selection
#Quickly release and click the '''B''' button again.
+
#After few seconds the device will be reset, which is signaled with the '''Red''', fading visual indicator color.
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Identify the S1 switch.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, three times press the '''S1 switch'''.
+
#Press the '''B''' button quickly, three times in a row.
 +
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 2,943: Line 3,057:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, three times press the '''S1 switch'''.
+
#Press the '''B''' button quickly, three times in a row.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,957: Line 3,071:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
+
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
|<div style="text-align: center;">'''<big>FGWPB-111 / FGWPB-121</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGRGBW-101</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Make sure the device is powered.
+
#Disconnect the supply voltage.
#Press and hold the button.
+
#Press and hold the '''B''' button located inside the RGBW Controllers casing.
#Wait for the LED frame to glow yellow (3rd menu position).
+
#Connect the the supply voltage, while still holding the '''B''' button.
#Release the button and then briefly click the button once to confirm the selection.
+
#Release the '''B''' button.
#After few seconds the device will restart with factory settings, which is signaled with the red frame color.
+
#The '''B''' channel will turn on (blue channel).
 +
#Disconnect  the power supply.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Plug the device into a socket.
+
('''Auto Inclusion''')
#The LED frame will glow red signaling it has not being added (If is doesn't you must first perform a general exclusion and then a factory reset).
+
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#Make sure the RGBW Controller is not connected to a supply.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Connect voltage supply to auto-include the RGBW Controller.
 +
#The RGBW Controller will be automatically recognized and included in the Z-Wave network.
 +
#Successful inclusion will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 
 +
'''(Manual Inclusion''')
 +
 
 +
#Make sure the RGBW Controller is not connected to a supply.
 +
#To disable auto-inclusion press the '''B''' button briefly, after re-connecting the RGBW Controller to its supply voltage.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, triple click the button located on the casing.
+
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
 +
#The RGBW Controller will be recognized and included in the Z-Wave network.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 2,982: Line 3,110:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Plug the device into a socket.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
+
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
#Quickly, triple click the button located on the casing.
 
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,998: Line 3,124:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
+
|<div style="text-align: center;">'''<big>Single Switch 2</big>'''</div>
|<div style="text-align: center;">'''<big>FGWPE-102</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGS-213</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the button located on the side.
+
#Switch off the mains voltage (disable the breaker).
#The device will cycle through GREEN, then VIOLET, and finally YELLOW for device reset.
+
#Remove the Switch 2 from the wall switch box.
#Release the button.
+
#Switch on the mains voltage.
#Press the button again to confirm the selection and factory reset the device.
+
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
 +
#Quickly release and click the '''B''' button again.
 +
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Plug the device into a socket nearby the main Z-Wave controller.
+
#Identify the S1 switch.
#The LED frame will glow red signaling not being added (reset or remove the device otherwise).
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, triple click the button on the side of the device.
+
#Quickly, three times press the '''S1 switch'''.
#The device will be included to the Z-Wave network.
+
#Successful inclusion will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, triple click the button on the side of the device.
+
#Quickly, three times press the '''S1 switch'''.
#Plug the device into a socket nearby the main Z-Wave controller.
 
#The LED frame will glow green signaling being added (removing is not necessary otherwise).
 
#Quickly, triple click the button on the side of the device.
 
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 3,038: Line 3,163:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer 2</big>'''</div>
+
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
|<div style="text-align: center;">'''<big>FGS-212</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGWPB-111 / FGWPB-121</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Switch off the mains voltage (disable the breaker).
+
#Make sure the device is powered.
#Remove the Dimmer 2 from the wall switch box.
+
#Press and hold the button.
#Switch on the mains voltage.
+
#Wait for the LED frame to glow yellow (3rd menu position).
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
+
#Release the button and then briefly click the button once to confirm the selection.
#Quickly release and click the '''B''' button again.
+
#After few seconds the device will restart with factory settings, which is signaled with the red frame color.
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
 
#The device enters the calibration mode.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing).
+
#Plug the device into a socket.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#The LED frame will glow red signaling it has not being added (If is doesn't you must first perform a general exclusion and then a factory reset).
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly press switch no. 1 or the '''B''' button three times.
+
#Quickly, triple click the button located on the casing.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 3,064: Line 3,188:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Plug the device into a socket.
 
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly press switch no. 1 or the '''B''' button three times.
+
#The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
 +
#Quickly, triple click the button located on the casing.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
#Dimmer 2 will start the calibration process
 
  
 
<hr />
 
<hr />
=='''<big>First Alert</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,079: Line 3,203:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>First Alert</big>'''</div>
+
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Smoke & Carbon Monoxide Combo Alarm</big>''' </div>
+
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
|<div style="text-align: center;">'''<big>ZCOMBO-G</big>'''</div>
+
|<div style="text-align: center;">'''<big>FGWPE-102</big>'''</div>
|<div style="text-align: center;">'''<big>Smoke / CO Detector</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Power up the device with the test button held down for 10+ seconds
+
#Press and hold the button located on the side.
#The device will reset all Z-Wave settings and leave the network. '''NOTE: The device will not remain awake after resetting and will go into standby mode.'''
+
#The device will cycle through GREEN, then VIOLET, and finally YELLOW for device reset.
 +
#Release the button.
 +
#Press the button again to confirm the selection and factory reset the device.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#Slide battery door open and insert batteries.
+
#Plug the device into a socket nearby the main Z-Wave controller.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#The LED frame will glow red signaling not being added (reset or remove the device otherwise).
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
+
#Quickly, triple click the button on the side of the device.
 +
#The device will be included to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,101: Line 3,229:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide battery door open, then remove and re-insert batteries.
+
#Quickly, triple click the button on the side of the device.
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
+
#Plug the device into a socket nearby the main Z-Wave controller.
 +
#The LED frame will glow green signaling being added (removing is not necessary otherwise).
 +
#Quickly, triple click the button on the side of the device.
 +
#The device will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
=='''<big>GE/Jasco</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,113: Line 3,243:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GE</big>'''</div>
+
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
|<div style="text-align: center;">'''<big>Link Bulb</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer 2</big>'''</div>
|<div style="text-align: center;"></div>
+
|<div style="text-align: center;">'''<big>FGS-212</big>'''</div>
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn OFF the light for 3 second.
+
#Switch off the mains voltage (disable the breaker).
#Turn ON the light for 3 seconds
+
#Remove the Dimmer 2 from the wall switch box.
#Repeat this process 5 times
+
#Switch on the mains voltage.
#The bulb will dim and then flash once when successfully reset.
+
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
 +
#Quickly release and click the '''B''' button again.
 +
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
 +
#The device enters the calibration mode.
  
'''Join the Zigbee Network'''
+
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
+
#Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing).
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Turn the bulb on.
+
#Quickly press switch no. 1 or the '''B''' button three times.
#The bulb will flash when connected to the hub.
+
#Successful inclusion will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
  
'''Leaving the Zigbee Network'''
+
'''Exclusion from the Z-Wave Network'''
  
#From the device's details page, select Remove Device, then Remove.
+
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly press switch no. 1 or the '''B''' button three times.
 +
#The device will be excluded from the Z-Wave network.
 +
#Dimmer 2 will start the calibration process
  
 
<hr />
 
<hr />
 +
=='''<big>First Alert</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,144: Line 3,285:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
+
|<div style="text-align: center;">'''<big>First Alert</big>'''</div>
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smoke & Carbon Monoxide Combo Alarm</big>''' </div>
|<div style="text-align: center;">'''<big>12718</big>'''</div>
+
|<div style="text-align: center;">'''<big>ZCOMBO-G</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smoke / CO Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Power up the device with the test button held down for '''10''' or more seconds
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#The device will reset all Z-Wave settings and leave the network. '''NOTE: The device will not remain awake after resetting and will go into standby mode.'''
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#Slide battery door open and insert batteries.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,167: Line 3,307:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Slide battery door open, then remove and re-insert batteries.
 +
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
  
 
<hr />
 
<hr />
 +
=='''<big>FortrezZ</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,177: Line 3,319:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
+
|<div style="text-align: center;">'''<big>FortrezZ</big>'''</div>
|<div style="text-align: center;">'''<big>Plug-in Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Multiple In / Out module</big>''' </div>
|<div style="text-align: center;">'''<big>12719/ZW4101</big>'''</div>
+
|<div style="text-align: center;">'''<big>MIMO2+</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Press and hold the program button for '''15''' seconds and then release.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Briefly press the program button once.
 +
#The status LED will flash when inclusion to the Z-Wave network completes.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,200: Line 3,340:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Briefly press the program button once.
 +
#The status LED will flash when the device has been excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 3,210: Line 3,351:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
+
|<div style="text-align: center;">'''<big>FortrezZ</big>'''</div>
|<div style="text-align: center;">'''<big>Outdoor Plug-in Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Multiple In / Out module</big>''' </div>
|<div style="text-align: center;">'''<big>12720/ZW4201</big>'''</div>
+
|<div style="text-align: center;">'''<big>MIMOLite</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Press and hold the program button for '''15''' seconds and then release.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#When the LED has a periodic single flash, the unit will be automatically included to the Z-Wave network.
 +
#If the LED is not flashing, then the  button has been previously pressed and automatic inclusion mode is no longer active. In this case, briefly press the program button once.
 +
#The status LED will flash when the device has been excluded from the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,233: Line 3,373:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Briefly press the program button once.
 +
#The status LED will flash when the device has been excluded from the Z-Wave network.
 +
 
 +
<hr />
 +
=='''<big>GE/Jasco</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>GE</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Link Bulb</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 
 +
#Turn OFF the light for '''3''' second.
 +
#Turn ON the light for '''3''' seconds
 +
#Repeat this process '''5''' times
 +
#The bulb will dim and then flash once when successfully reset.
 +
 
 +
'''Join the Zigbee Network'''
 +
 
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Turn the bulb on.
 +
#The bulb will flash when connected to the hub.
 +
 
 +
'''Leaving the Zigbee Network'''
 +
 
 +
#From the device's details page, select Remove Device, then Remove.
  
 
<hr />
 
<hr />
Line 3,244: Line 3,417:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;"> '''<big>In-Wall Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>12721</big>'''</div>
+
|<div style="text-align: center;">'''<big>12718</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 3,257: Line 3,430:
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
#Single press and release the manual/program button on the device to include it in the network.
Line 3,277: Line 3,450:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;"> '''<big>In-Wall Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug-in Switch</big>'''</div>
|<div style="text-align: center;">'''<big>12722</big>'''</div>
+
|<div style="text-align: center;">'''<big>12719/ZW4101</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
Line 3,285: Line 3,458:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
+
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
+
#Single press and release the manual/program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,299: Line 3,472:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
+
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,310: Line 3,483:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;"> '''<big>In-Wall Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outdoor Plug-in Switch</big>'''</div>
|<div style="text-align: center;">'''<big>12724</big>'''</div>
+
|<div style="text-align: center;">'''<big>12720/ZW4201</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 3,318: Line 3,491:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
+
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
+
#Single press and release the manual/program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,332: Line 3,505:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
+
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,343: Line 3,516:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Toggle Switch</big>'''</div>
+
|<div style="text-align: center;"> '''<big>In-Wall Outlet</big>'''</div>
|<div style="text-align: center;">'''<big>12727</big>'''</div>
+
|<div style="text-align: center;">'''<big>12721</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 3,351: Line 3,524:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press up and release the toggle switch to perform a general exclusion.
+
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press up and release the toggle switch to include it in the network.
+
#Single press and release the manual/program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,365: Line 3,538:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press up and release the toggle switch to exclude it from the network.
+
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,376: Line 3,549:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Toggle Dimmer</big>'''</div>
+
|<div style="text-align: center;"> '''<big>In-Wall Switch</big>'''</div>
|<div style="text-align: center;">'''<big>12729</big>'''</div>
+
|<div style="text-align: center;">'''<big>12722</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 3,384: Line 3,557:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press up and release the toggle switch to perform a general exclusion.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press up and release the toggle switch to include it in the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,398: Line 3,571:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press up and release the toggle switch to exclude it from the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,409: Line 3,582:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
+
|<div style="text-align: center;"> '''<big>In-Wall Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>12730/ZW4002</big>'''</div>
+
|<div style="text-align: center;">'''<big>12724</big>'''</div>
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
Line 3,417: Line 3,590:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,431: Line 3,604:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,442: Line 3,615:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Plug-In Outdoor Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Toggle Switch</big>'''</div>
|<div style="text-align: center;">'''<big>14284</big>'''</div>
+
|<div style="text-align: center;">'''<big>12727</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Unplug the switch from the outlet
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
#Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet
+
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press up and release the toggle switch to perform a general exclusion.
 +
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Press up and release the toggle switch to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,462: Line 3,637:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Press up and release the toggle switch to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,473: Line 3,648:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Toggle Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>14287</big>'''</div>
+
|<div style="text-align: center;">'''<big>12729</big>'''</div>
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
#The LED will flash ON/OFF 5 times when completed successfully.
+
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press up and release the toggle switch to perform a general exclusion.
 +
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
+
#Press up and release the toggle switch to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,493: Line 3,670:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
+
#Press up and release the toggle switch to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
 
  
 
<hr />
 
<hr />
Line 3,505: Line 3,681:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Tamper Resistant Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
|<div style="text-align: center;">'''<big>14288</big>'''</div>
+
|<div style="text-align: center;">'''<big>12730/ZW4002</big>'''</div>
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
+
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the manual/program button 3 times, then press and hold the button for at least 3 seconds. The LED will blink 5 times to confirm.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
 +
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,524: Line 3,703:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,535: Line 3,714:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug-In Outdoor Switch</big>'''</div>
|<div style="text-align: center;">'''<big>14291</big>'''</div>
+
|<div style="text-align: center;">'''<big>14284</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#Unplug the switch from the outlet
#The LED will flash ON/OFF 5 times when completed successfully.
+
#Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless smart switch rocker to add it in the network.
+
#Single press and release the manual/program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,555: Line 3,734:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
+
#Single press and release the manual/program button on the device to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
 
  
 
<hr />
 
<hr />
Line 3,567: Line 3,745:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
|<div style="text-align: center;">'''<big>14294</big>'''</div>
+
|<div style="text-align: center;">'''<big>14287</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
#The LED will flash ON/OFF 5 times when completed successfully.
+
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
+
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,587: Line 3,765:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
+
#Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
+
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,599: Line 3,777:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Tamper Resistant Outlet</big>'''</div>
|<div style="text-align: center;">'''<big>26931</big>'''</div>
+
|<div style="text-align: center;">'''<big>14288</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the top button '''10 times''' within five seconds.
+
#Press the manual/program button '''3''' times, then press and hold the button for at least '''3''' seconds. The LED will flash '''5''' times to confirm.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom button on the smart switch to include it in the network.
+
#Single press and release the manual/program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,618: Line 3,796:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top or bottom button on the smart switch to exclude it from the network.
+
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,629: Line 3,807:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
|<div style="text-align: center;">'''<big>26933</big>'''</div>
+
|<div style="text-align: center;">'''<big>14291</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the top button '''10 times''' within five seconds. The LED will flash 3 times quickly confirming change
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
 +
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the top or bottom button on the smart switch to include it in the network.
+
#Press and release the top or bottom of the wireless smart switch rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,648: Line 3,827:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the top button on the smart switch to exclude it from the network.
+
#Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
 +
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,659: Line 3,839:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>28167</big>'''</div>
+
|<div style="text-align: center;">'''<big>14294</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#If plugged in, unplug the Dimmer from the receptacle.
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
#Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
+
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,679: Line 3,859:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
 +
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,690: Line 3,871:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
|<div style="text-align: center;">'''<big>28169</big>'''</div>
+
|<div style="text-align: center;">'''<big>26931</big>'''</div>
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#If plugged in, unplug the Dimmer from the receptacle.
+
#Press and release the top button '''10''' times within '''5''' seconds.
#Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the manual/program button on the device to include it in the network.
+
#Press and release the top or bottom button on the smart switch to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,710: Line 3,890:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the manual/program button on the device to exclude it from the network.
+
#Press and release the top or bottom button on the smart switch to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,721: Line 3,901:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Hinge Pin Smart Door Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
|<div style="text-align: center;">'''<big>32563/ZW6301</big>'''</div>
+
|<div style="text-align: center;">'''<big>26933</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the program button ten times quickly.
+
#Press and release the top button '''10''' times within '''5''' seconds. The LED will flash '''3''' times quickly confirming change
#The LED light will blink approximately eight times.
 
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Single press and release the program button on the device to include it in the network.
+
#Press and release the top or bottom button on the smart switch to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,741: Line 3,920:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Single press and release the program button on the device to exclude it from the network.
+
#Press and release the top button on the smart switch to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,752: Line 3,931:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>45856</big>'''</div>
+
|<div style="text-align: center;">'''<big>28167</big>'''</div>
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
+
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the top of the rocker (ON Switch) 10x quickly (short presses)
+
#If plugged in, unplug the Dimmer from the receptacle.
 +
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
  
'''Join the Zigbee Network'''
+
'''Join the Z-Wave Network'''
  
#Remove power from the dimmer at the circuit breaker.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Restore power to the Smart Dimmer at the circuit breaker
+
#Single press and release the manual/program button on the device to include it in the network.
#Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
 
#*'''Note:''' ''LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
 
  
'''Leaving the Zigbee Network'''
+
'''Exclusion from the Z-Wave Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove.'''
+
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,783: Line 3,962:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
+
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>45857</big>'''</div>
+
|<div style="text-align: center;">'''<big>28169</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Lift the air-gap switch at the bottom of the rocker to OFF position to power down the device.
+
#If plugged in, unplug the Dimmer from the receptacle.
#Hold down the UP button
+
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
#Push In the air-gap switch to ON position to power up the device.
 
#Release the UP button within 4 seconds of power up.
 
  
'''Join the Zigbee Network'''
+
'''Join the Z-Wave Network'''
  
#Remove power from the dimmer at the circuit breaker.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Restore power to the Smart Dimmer at the circuit breaker
+
#Single press and release the manual/program button on the device to include it in the network.
#Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
 
#*'''Note:''' ''LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
 
  
'''Leaving the Zigbee Network'''
+
'''Exclusion from the Z-Wave Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove.'''
+
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Single press and release the manual/program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
=='''<big>GoControl</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,817: Line 3,992:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GoControl</big>'''</div>
+
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Garage Door Controllers</big>'''</div>
+
|<div style="text-align: center;">'''<big>Hinge Pin Smart Door Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>GD00Z</big>'''</div>
+
|<div style="text-align: center;">'''<big>32563/ZW6301</big>'''</div>
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
+
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
|}''Includes Linear GD00Z-2, GoControl GD00Z-4, Linear GD00Z-5, ADT GD00Z-6, GoControl GD00Z-7 and NuTone ND00Z''
+
|}'''Factory Reset'''
 
 
'''Factory Reset'''
 
  
#Reset the controller by pressing the Link button 5 times.
+
#Press and release the program button '''10''' times quickly.
#A quick beep followed by a longer beep will indicate proper reset of the GD00Z series or ND00Z.
+
#The LED light will flash approximately eight times.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and release the Link button.
+
#Single press and release the program button on the device to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 3,840: Line 4,013:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and release the Link button.
+
#Single press and release the program button on the device to exclude it from the network.
  
 
<hr />
 
<hr />
Line 3,850: Line 4,023:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>GoControl</big>'''</div>
+
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
|<div style="text-align: center;">'''<big>WADWAZ-1</big>'''</div>
+
|<div style="text-align: center;">'''<big>45856</big>'''</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Tap the top of the rocker (ON Switch) with '''10''' quick short presses.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
 
  
'''Join the Z-Wave Network'''
+
'''Join the Zigbee Network'''
  
#Unscrew the screw fastening the rear cover and slide the rear cover down
+
#Remove power from the dimmer at the circuit breaker.
#Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the sensor has not yet performed inclusion with the controller.
+
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Once Hubitat Elevation™ discovers the device, the LED will stop blinking. If the LED does not stop blinking and is not discovered by your hub, relocate the WADWAZ-1 to within 100 feet (line of sight) of a Z-Wave repeater or your hub and restart Z-Wave pairing.
+
#Restore power to the Smart Dimmer at the circuit breaker
 +
#Pairing Begins Automatically: LED Status Indicator flashs as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 +
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
 +
#*'''Note:''' ''LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
  
'''Exclusion from the Z-Wave Network'''
+
'''Leaving the Zigbee Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove'''
+
#From the device's details page, select '''Remove Device''', then '''Remove.'''
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
 
  
 
<hr />
 
<hr />
=='''<big>Graber</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 3,885: Line 4,054:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Graber</big>'''</div>
+
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
|<div style="text-align: center;">'''<big>Motorized Shades</big>'''</div>
+
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
|
+
|<div style="text-align: center;">'''<big>45857</big>'''</div>