Difference between revisions of "Join and Reset Instructions"

From Hubitat Documentation
Jump to: navigation, search
(Added Iris v1 Keyfob, v1 Motion Sensor, v1 Smart Plug, v2 Button and v2 Door/Window Sensor)
(Added Orvibo SN11 Motion Sensor)
 
(27 intermediate revisions by the same user not shown)
Line 1: Line 1:
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into '''Paring Mode''' using the manufacturer's instructions, Z-Wave devices must be '''Excluded''' from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a '''General Exclusion''' in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show '''Unknown Device Excluded''' in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
+
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
  
 
=='''<big>ADT</big>'''==
 
=='''<big>ADT</big>'''==
Line 4,514: Line 4,514:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Once the controller is ready to include your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
+
#Once the controller is ready to exclude your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
  
 
<hr />
 
<hr />
Line 4,747: Line 4,747:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.  
+
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Remove the battery for at least 10 seconds. Reinsert the battery.
 
#Remove the battery for at least 10 seconds. Reinsert the battery.
 
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.  
 
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.  
Line 4,766: Line 4,766:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.  
+
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Remove the battery for at least 10 seconds. Reinsert the battery.
 
#Remove the battery for at least 10 seconds. Reinsert the battery.
 
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.  
 
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.  
Line 4,831: Line 4,831:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove battery. Wait 10 seconds then re-insert battery.  
+
#Remove battery. Wait 10 seconds then re-insert battery.
 
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
 
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
Line 4,850: Line 4,850:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Remove battery. Wait 10 seconds then re-insert battery.  
+
#Remove battery. Wait 10 seconds then re-insert battery.
 
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
 
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
Line 4,877: Line 4,877:
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#'''Hold for an additional two seconds''' and release. The contact sensor should begin blinking blue.
 
#'''Hold for an additional two seconds''' and release. The contact sensor should begin blinking blue.
#* '''NOTE:''' ''The reset button is a small black button above the battery.''
+
#*'''NOTE:''' ''The reset button is a small black button above the battery.''
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,884: Line 4,884:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove battery. Wait 10 seconds then re-insert battery.  
+
#Remove battery. Wait 10 seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
 
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
Line 4,906: Line 4,906:
 
|-
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
|<div style="text-align: center;">'''<big>V2 Door/Window Sensor</big>''' </div>
+
|<div style="text-align: center;">'''<big>Garage Door Opener</big>''' </div>
 +
|<div style="text-align: center;">
 +
'''<big>GD-00Z-1</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}
 +
 
 +
'''Factory Reset'''
 +
 
 +
#Unplug your device - wait 10 seconds
 +
#Restore power to the device
 +
#Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
 +
 
 +
'''Join the Z-Wave Network'''
 +
 
 +
#Perform a factory reset before attempting to join the Z-Wave network.
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Ensure your Iris Garage Door Controller is plugged in, and the tilt sensor battery is active/working.
 +
#Press the Link (Z-Wave) button once located on the left of the Iris Garage Door Controller.
 +
#When your device triple beeps, it has successfully joined the Z-Wave network.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 
 +
'''Exclusion the Z-Wave Network'''
 +
 
 +
#From the device's details page, select Remove Device, then Remove
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Once the controller is ready to exclude your device, press the Link (Z-Wave) button once located on the left side of the device.
 +
#The garage door controller should give a short beep immediately followed by a long beep.
 +
 
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 +
|<div style="text-align: center;">'''<big>V2 Keypad</big>''' </div>
 
|<div style="text-align: center;">
 
|<div style="text-align: center;">
'''<big>3320-L</big>'''
+
'''<big>3405-L</big>'''
 
</div>
 
</div>
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
+
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}  
 
|}  
Line 4,916: Line 4,958:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Slide off the battery cover, remove the battery and wait ten seconds.
+
#Remove the battery and wait ten seconds.
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
+
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
#'''Hold for an additional two seconds''' and release. The contact sensor should begin blinking blue.
+
#*Note: The factory reset process puts the security keypad back into pairing mode.
#* '''NOTE:''' ''The reset button is a small black button above the battery.''
+
#Upon a proper reset the top right icon will be blinking green on your keypad.
 +
#You may now insert the 2nd battery.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,926: Line 4,969:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove battery. Wait 10 seconds then re-insert battery.  
+
#Remove battery. Wait 10 seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
 
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
  
Line 4,934: Line 4,976:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Slide off the battery cover, remove the battery and wait ten seconds.
+
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
+
#*Note: The factory reset process puts the security keypad back into pairing mode.
#'''Hold for an additional two seconds''' and release. The contact sensor should begin blinking blue.
+
#Upon a proper reset the top right icon will be blinking green on your keypad.
#*'''NOTE:''' ''The reset button is a small black button above the battery''
+
#You may now insert the 2nd battery.
  
 
<hr />
 
<hr />
=='''<big>Kwikset</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 4,948: Line 4,989:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
+
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
+
|<div style="text-align: center;">'''<big>V3 Keypad</big>''' </div>
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
+
|<div style="text-align: center;">
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
+
'''<big>iL02_1</big>'''
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
</div>
|}'''Factory Reset'''
+
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}  
 +
 
 +
'''Factory Reset'''
  
#Remove battery pack
+
#Remove only 1 AA battery and wait ten seconds.
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
+
#A blinking blue light indicates the device is reset and ready to pair again.
#Perform the '''door handing''' process again.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
 
  
'''Join the Z-Wave Network'''
+
'''Join the Zigbee Network'''
  
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
+
#Remove only 1 AA battery and wait ten seconds.
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#A blinking blue light indicates the device is reset and ready to pair again.
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
+
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.
+
#Watch the status in the device details page to confirm proper operation.
  
'''Exclusion from the Z-Wave Network'''
+
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
+
#Remove only 1 AA battery and wait ten seconds.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
+
#A blinking blue light indicates the device is reset and ready to pair again.
  
 
<hr />
 
<hr />
Line 4,988: Line 5,029:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
+
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
+
|<div style="text-align: center;">'''<big>V2 Motion Sensor</big>''' </div>
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
+
|<div style="text-align: center;">
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
+
'''<big>3326-L</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
|}'''Factory Reset'''
+
|}  
 
+
 
#Remove battery pack
+
'''Factory Reset'''
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
+
 
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
+
#Remove the battery and wait 10 seconds
#Perform the '''door handing''' process again.
+
#Press and hold the reset button on the left side of the device as you reinsert the battery.
#*Press and hold the Lock button while installing battery pack.
+
#Hold for an additional two seconds and release.
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
+
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
+
#Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
 +
#A blinking blue light indicates the device is reset and ready to pair again.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
  
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
+
#Factory reset the device before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
+
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press button '''A''' on the lock '''4 times''' to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
+
#Remove the battery for 10 seconds and re-insert.
#*If pairing is unsuccessful, press button '''B''' on the lock '''9 times''' and repeat the pairing process.
+
#Replace the battery cover. The sensor's blue LED will flash while searching for the hub.
 +
#Once paired the LED will stop blinking.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
#From the device's details page, select '''Remove Device''', then '''Remove.'''
+
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Press button '''B''' on the lock '''9 times.'''
+
#Press and hold the reset button on the left side of the device as you reinsert the battery.
 +
#Hold for an additional two seconds and release.
 +
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
 +
#Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
 +
#A blinking blue light indicates the device is reset and ready to pair again.
  
 
<hr />
 
<hr />
=='''<big>Leviton</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 5,025: Line 5,075:
 
|<div style="text-align: center;">Protocol</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|-
|<div style="text-align: center;">'''<big>Leviton</big>'''</div>
+
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
|<div style="text-align: center;">'''<big>4-Scene Controller</big>'''</div>
+
|<div style="text-align: center;">'''<big>V3 Motion Sensor</big>''' </div>
|<div style="text-align: center;">'''<big>VRCS4</big>'''</div>
+
|<div style="text-align: center;">
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
+
'''<big>iL07_1</big>'''
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
</div>
|}'''Factory Reset'''
+
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}  
 +
 
 +
'''Factory Reset'''
 +
 
 +
#Remove the battery and wait ten seconds.
 +
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
 +
#A blinking blue light indicates the device is ready to pair.
 +
 
 +
'''Join the Zigbee Network'''
  
#On the 4-Scene controller, press and hold buttons 1 and 3.
+
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
#Wait approximately 5 seconds until the LED turns amber and then solid red.
+
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
+
#Remove the battery and wait ten seconds.
 +
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
 +
#A blinking blue light indicates the device is ready to pair.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
  
'''Join the Z-Wave Network'''
+
'''Leaving the Zigbee Network'''
  
'''Leaving the Z-Wave Network'''<hr />
+
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Remove the battery and wait ten seconds.
 +
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
 +
#A blinking blue light indicates the device is ready to pair.
  
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 +
|<div style="text-align: center;">'''<big>V2 Smart Plug</big>''' </div>
 +
|<div style="text-align: center;">
 +
'''<big>3210-L</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Remove the Smart Plug from the outlet and wait ten seconds.
 +
#Press and hold the small white button on the front of the plug.
 +
#While holding the button, insert the Smart Plug back into the outlet.
 +
#As soon as the LED on the front of the plug lights up, release the button.
 +
#If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Factory reset the device before attempting to pair.
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Insert your smart plug into any wall outlet. Your smart plug should be blinking blue, that means it's in pairing mode.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Press and hold the small white button on the front of the plug.
 +
#While holding the button, insert the Smart Plug back into the outlet.
 +
#As soon as the LED on the front of the plug lights up, release the button.
 +
#If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 +
|<div style="text-align: center;">'''<big>V2 Smart Fob</big>''' </div>
 +
|<div style="text-align: center;">
 +
'''<big>3450-L</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Twist open the battery cover on the back of the Smart Fob.
 +
#Remove the battery and wait ten seconds
 +
#Reinstall the battery with the positive side facing you.
 +
#Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
 +
#Confirm that the fob has been reset by checking that the fob's background light is flashing blue. If it does not do this, check the battery and retry from step 2.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Factory reset the device before attempting to pair.
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
 +
#The Smart Fob's LED will blink blue while searching for the hub.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Twist open the battery cover on the back of the Smart Fob.
 +
#Remove the battery and wait ten seconds
 +
#Reinstall the battery with the positive side facing you.
 +
#Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Smart Water Sensor</big>''' </div>
 +
|<div style="text-align: center;">
 +
'''<big>3315-L</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Remove the cover from the sensor, then remove the battery for at least 10 seconds.
 +
#Press and hold the reset button while reinserting the battery.
 +
#Hold for an additional two seconds and release.
 +
#A successful reset will be indicated by a blinking blue light on your sensor
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Factory reset the device before attempting to pair.
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Remove the battery and wait ten seconds.
 +
#Re-insert the battery
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Remove the cover from the sensor, then remove the battery for at least 10 seconds.
 +
#Press and hold the reset button while reinserting the battery.
 +
#Hold for an additional two seconds and release.
 +
#A successful reset will be indicated by a blinking blue light on your sensor
 +
 +
<hr />
 +
 +
=='''<big>KEEN Home</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>KEEN Home</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Smart Vent</big>''' </div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Vent</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Press the black button on the back inside of the Smart Vent battery compartment five times.
 +
#You will know that the Smart Vent has been properly reset when the LED starts double blinking green
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Removed the battery cartridge and reinsert it to bring the vent online.
 +
#Press the black button on the back inside of the Smart Vent battery compartment five times.
 +
#This should force the vent into join-mode once again.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Press the black button on the back inside of the Smart Vent battery compartment five times.
 +
#You will know that the Smart Vent has been properly reset when the LED starts double blinking green
 +
 +
<hr />
 +
=='''<big>Kwikset</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
 +
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
 +
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove battery pack
 +
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
 +
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
 +
#Perform the '''door handing''' process again.
 +
#*Press and hold the Lock button while installing battery pack.
 +
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 +
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
 +
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
 +
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
 +
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove battery pack
 +
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
 +
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
 +
#Perform the '''door handing''' process again.
 +
#*Press and hold the Lock button while installing battery pack.
 +
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 +
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press button '''A''' on the lock '''4 times''' to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
 +
#*If pairing is unsuccessful, press button '''B''' on the lock '''9 times''' and repeat the pairing process.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Press button '''B''' on the lock '''9 times.'''
 +
 +
<hr />
 +
 +
=='''<big>Leak Intelligence</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Leak Intelligence</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Leak Gopher</big>''' </div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Unplug your device - wait 10 seconds
 +
#Restore power to the device
 +
#Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press the Z-Wave button once.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Exclusion the Z-Wave Network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Once the controller is ready to exclude your device, press the Z-Wave button once.
 +
 +
<hr />
 +
=='''<big>Leviton</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Leviton</big>'''</div>
 +
|<div style="text-align: center;">'''<big>4-Scene Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>VRCS4</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#On the 4-Scene controller, press and hold buttons 1 and 3.
 +
#Wait approximately 5 seconds until the LED turns amber and then solid red.
 +
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
 +
 +
'''Join the Z-Wave Network'''
 +
 +
'''Leaving the Z-Wave Network'''<hr />
 +
 +
=='''<big>Linear</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>WADWAZ-1</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Factory reset is achieved by performing a general exclusion.
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*'''See [[Discovering your Devices|Discovering your devices]] for detail instructions.'''
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#The LED on the sensor will stop blinking
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Exclusion the Z-Wave Network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Tamper switch of WADWAZ-1 for 1 second and release to exclude the device form the Z-wave network.
 +
#The LED light will flash continuously when the sensor is in the excluded condition.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 +
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
 +
|<div style="text-align: center;">'''<big>WAPIRZ-1</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Factory reset is achieved by performing a general exclusion.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#The LED on the sensor will stop blinking
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Exclusion the Z-Wave Network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Tamper switch of WAPIRZ-1 for 1 second and release to exclude the device form the Z-wave network.
 +
#The LED light will flash continuously when the sensor is in the excluded condition.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Siren / Strobe</big>'''</div>
 +
|<div style="text-align: center;">'''<big>WA105DBZ-1</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Factory reset is achieved by performing a general exclusion.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#The LED on the sensor will stop blinking
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Exclusion the Z-Wave Network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
 +
#The LED light will flash continuously when the sensor is in the excluded condition.
 +
 +
<hr />
 +
=='''<big>Lutron</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Dimmers and Switches</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Dimmer / Switch</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the "On" button quickly three times, holding on the last press.
 +
#Continue to hold the "On" button until the light begins to flash quickly.
 +
#Release the button, then immediately tap the button three more times.
 +
#All paired Pico remote controls are removed and all settings are returned to factory default.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Caséta Smart Bridge Pro</big>'''</div>
 +
|<div style="text-align: center;">'''<big>L-BDGPRO2</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Bridge</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Network Reset'''
 +
 +
#First, press and hold the black button on the back of your Smart Bridge for 20 seconds.
 +
 +
'''Factory Reset'''
 +
 +
#Quickly triple tap and hold the Add button. DO NOT release after the third tap.
 +
#Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
 +
#Release the button and quickly perform another triple tap of the button. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
 +
#The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
 +
 +
'''NOTE''': ''Lutron does not recommend factory resetting a Smart Bridge Pro unless advised by a member of the Lutron technical support team.''<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Pico Remote</big>'''</div>
 +
|<div style="text-align: center;">'''<big>PJ2-</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the "On" button quickly three times, holding on the last press.
 +
#Continue to hold the "On" button until the light begins to flash quickly.
 +
#Release the button, then immediately tap the button three more times.
 +
#All paired Pico remote controls are removed and all settings are returned to factory default.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Radio RA2 Keypads</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the "On" button quickly three times, holding on the last press.
 +
#Continue to hold the "On" button until the light begins to flash quickly.
 +
#Release the button, then immediately tap the button three more times.
 +
#The RA2 keypad has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Radio RA2 Main Repeater</big>'''</div>
 +
|<div style="text-align: center;">'''<big>RR-MAIN-REP</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Triple tap and hold the Test button on a Main Repeater. DO NOT release the button after the third tap.
 +
#Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately 3 seconds).
 +
#Release the Test button and immediately triple tap it again. All the LEDs will flash red quickly.
 +
#When the LEDs stop flashing, the Main Repeater has been returned to factory settings
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Radio RA2 Occupancy Sensors</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
*'''Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)'''
 +
 +
#Quickly triple tap and hold the Test, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
 +
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 +
#Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 +
#The Sensor has now been returned to Factory Default Settings.
 +
 +
*'''Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)'''
 +
 +
#Quickly triple tap and hold the Test or Light button on the Sensor. DO NOT release after third tap.
 +
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 +
#Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 +
#The Sensor has now been returned to Factory Default Settings.
 +
 +
*'''Radio Powr SavrTM Occupancy/Vacancy Wall-Mounted Sensor'''
 +
 +
#Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
 +
#Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
 +
#Release the button and triple tap the button again until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 +
#The Sensor has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Radio RA2 Select Main Repeater</big>'''</div>
 +
|<div style="text-align: center;">'''<big>RR-SEL-REP2</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Quickly triple tap and hold down any button on the Main Repeater. DO NOT release after the third tap.
 +
#Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash red slowly (approximately once per second).
 +
#Release the button and quickly perform another triple tap of the button. The Main Repeater LEDs will flash green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 +
#The Main Repeater and system components have now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device.<hr />
 +
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>RadioRA2 VCRX Visor Control Receiver</big>'''</div>
 +
|<div style="text-align: center;">'''<big>RR-VCRX</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Garage Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Quickly triple tap and hold any button (except Learn) on the VCRX. DO NOT release after third tap.
 +
#Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
 +
#Release the button and triple tap the button again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 +
#The VCRX has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device.<hr />
 +
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Serena Shades</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Shade Control</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
 +
#Immediately tap the shade button quickly three more times, until the shade button LED blinks green rapidly, then blinks red/green three times, and turns off.
 +
#The Serena shade has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device<hr />
 +
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Sivoia QS Triathlon Shades</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Shade Control</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
 +
#Immediately tap the shade button quickly three more times, until the shade button LED blinks '''Green''' rapidly, then blinks '''Red/Green''' three times, and turns off.
 +
#The Sivoia shade has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>RadioRA2 Fan Control</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>RRD-2ANF</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Triple tap the tapswitch on a control. DO NOT release after the third tap.
 +
#Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
 +
#Release the tapswitch and immediately triple tap the tapswitch again.
 +
#The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device.<hr />
 +
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Caséta Fan Control</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>PD-FSQN</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Tap the "On" button quickly three times, holding on the last press.
 +
#Continue to hold the "On" button until the light begins to flash quickly.
 +
#Release the button, then immediately tap the button three more times.
 +
#All paired Pico remote controls are removed and all settings are returned to factory default.
 +
 +
'''Join the Lutron Clear Connect network'''
 +
 +
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 +
 +
'''Leaving the Lutron Clear Connect network'''
 +
 +
#From the device's details page, select Remove Device, then Remove
 +
#Perform a factory reset on the device
 +
 +
<hr />
 +
=='''<big>LUX</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Lux</big>'''</div>
 +
|<div style="text-align: center;">'''<big>KONOz</big>'''</div>
 +
|<div style="text-align: center;"></div>
 +
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Access the installation settings by going to the main menu and selecting the gear icon.
 +
#You will see “IS” on the screen and will be prompted to select “yes” or “no”.
 +
#Select “yes” to access the  installation settings.
 +
#Rotate the knob to view settings and press the knob to confirm.
 +
#Once in the installer settings, rotate the knob to '''99'''.
 +
#Press the knob to confirm, then press and hold the knob for 3 seconds.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Perform factory reset.
 +
#KONOz is now ready to be configured for your heating and cooling system. The KONOz will guide you through the initial system configuration.
 +
#After confirming your system settings, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET” to establish a connection.
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Perform factory reset.
 +
 +
<hr />
 +
=='''<big>MCO Home</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>MCO Home</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Dimmer Switch</big>'''</div>
 +
|<div style="text-align: center;">'''<big>MH-DT311</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power.
 +
#The factory setting will be restored.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press 3 times on "+" or "-" button to add the device. If successful, the green LED blinks 4 times.
 +
#*Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED blinks 4 times.
 +
#*Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
 +
 +
<hr />
 +
=='''<big>Monoprice</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Door/Window Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>24259</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#To reset the sensor, press and hold the Z-button for about 20 seconds.
 +
#The LED will change from steadily illuminated to blinking then back to steadily illuminated, indicating that the reset operation was successful.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Rapidly press the Z-button 3 times to include the device in the network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Rapidly press the Z-button 3 times to exclude the device from the network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Plug-In Dimmer</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>11994</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure that the smart plug is inserted into an AC outlet.
 +
#Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Plug-In ON/OFF</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>11995</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure that the smart plug is inserted into an AC outlet.
 +
#Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Recessed Door/Window sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>15268</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for 2 seconds then disappear.
 +
#If linking was unsuccessful, the LED will continue to blink if you tap its button.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Z-button on your Sensor. If your switch has been successfully unlinked to your network, its LED will start to blink for a short time.
 +
#If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Door/Window Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>15270</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure that the smart plug is inserted into an AC outlet.
 +
#Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>PIR Motion Sensor with Temperature</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>15271</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure that the smart plug is inserted into an AC outlet.
 +
#Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Plug-in Outlet</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>15654</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}
 +
 +
'''Factory Reset'''
 +
 +
#Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can jooin the Hubitat Elevation™ Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Triple-click the Z-Button. The plug-in will be removed from your Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>4 in 1 motion sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>15902</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network and has returned it to a factory state.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Momentarily press the '''Program Switch'''
 +
#The LED should blink 5 times indicating the sensor has not yet been included in the Z-Wave network.
 +
#If the LED blinks only 1 time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
 +
#Momentarily press the button again after it blinks 5 times, to automatically include the sensor in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Smart Plug and Repeater</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>27481</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure that the smart plug is inserted into an AC outlet.
 +
#Press and hold the Z-Button on the smart plug for more than 20 seconds.
 +
#The LED indicator will illuminate yellow steadily for about 2 seconds.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Rapidly press the Z-button 3 times to include the device in the network.
 +
 +
'''Testing the Smart Plug Z-Wave connection'''
 +
 +
You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.
 +
 +
To begin testing, press and hold the Z button for 6-9 seconds, releasing the button when the RGB LED illuminates violet.
 +
 +
*'''''Note'':''' The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
 +
**'''Blinking Green''': The RGB LED will blink green while the smart plug is attempting to establish a connection with the main controller.
 +
**'''Solid Green''': The RGB LED will illuminate green for about 2 seconds to indicate that direct communications are stable.
 +
**'''Blinking Orange''': The RGB LED will blink orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
 +
**'''Solid Orange''': The RGB LED will illuminate orange for about 2 seconds to indicate that the communication quality is moderate.
 +
**'''Solid Red''': The RGB LED will illuminate red for about 2 seconds to indicate that they communications attempt has failed.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Rapidly press the Z-button 3 times to exclude the device from the network.
 +
#The RGB LED will blink orange while the smart plug is being removed.
 +
#The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate orange steadily for about 2 seconds.
 +
 +
<hr />
 +
=='''<big>Neo</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">'''<big>Brand</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Device</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Product Number</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Device Type</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Protocol</big>'''</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Door/Window Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-DS01ZE</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove the cover of contact sensor main body.
 +
#Make sure the sensor is connected to power source.
 +
#Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
 +
#Release the button.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
 +
#The contact sensor will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Door/Window Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-DS02ZU</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove the cover of contact sensor main body.
 +
#Make sure the sensor is connected to power source.
 +
#Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
 +
#Release the button.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
 +
#The contact sensor will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Motion Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-PD01ZU-T</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove the sensor’s cover.
 +
#Make sure the sensor is connected to power source.
 +
#Press the code button for '''10 seconds''', the LED will flash red for '''1 time'''.
 +
#Release the code button.
 +
#*'''NOTE:''' When the PIR is being restored to factory settings, please make sure a power source is connected.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
 +
#The motion sensor will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Power Plug</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-WR02Z</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press and hold the code button on the front of the outlet for 10 seconds.
 +
#When the LED flashes, release the button.
 +
#When the outlet has been reset, the LED will flash on and off '''5 times''' within a 2 second period.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
 +
#The device will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the device will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>One Key SOS</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-RC03ZU</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press and hold the code button for 10 seconds.
 +
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the red SOS alarm button.
 +
#The device will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the red SOS alarm button and the device will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>One Key SOS and Remote Control</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NAS-RC03ZU</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press and hold the code button for 10 seconds.
 +
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly, '''triple-click''' the red SOS alarm button.
 +
#The device will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Quickly, '''triple-click''' the red SOS alarm button and the device will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
=='''<big>NodOn</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NodOn</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Octan Remote</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>CRC-3US-1</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#A simultaneous long press (1sec) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 +
#The LED will blink '''red''' and '''green''' to validate the reset.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
 +
#The LED glows in '''pink''' to confirm the selection
 +
#Push on the '''solid circle''' within 10 seconds.
 +
#The LED blinks in '''pink''' to confirm your choice and then blinks in '''green''' to confirm the procedure.
 +
#The device will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
 +
#The LED glows in '''pink''' to confirm the selection
 +
#Push on the '''solid circle''' within 10 seconds.
 +
#The LED blinks in '''pink''' to confirm your choice and then blinks in '''green''' to confirm the procedure
 +
#The device will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NodOn</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Soft Remote</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>CRC-3US-6</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#A simultaneous long press (1sec) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 +
#The LED will blink '''red''' and '''green''' to validate the reset.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
 +
#The LED glows in '''pink''' to confirm the selection
 +
#Push on the '''solid circle''' within 10 seconds.
 +
#The LED blinks in '''pink''' to confirm your choice and then blinks in '''green''' to confirm the procedure.
 +
#The device will be detected and included in the Z-Wave network.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
 +
#The LED glows in '''pink''' to confirm the selection
 +
#Push on the '''solid circle''' within 10 seconds.
 +
#The LED blinks in '''pink''' to confirm your choice and then blinks in '''green''' to confirm the procedure
 +
#The device will be excluded from the Z-Wave network.
 +
 +
<hr />
 +
=='''<big>NYCE</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Curtain Motion Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NCZ-3045-HA</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Press the button 4 times to join the device to the Zigbee network.
 +
#The LED will flash in the following sequences:
 +
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 +
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 +
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
 +
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Ceiling Motion Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NCZ-3043-HA</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 +
#Inside the battery compartment is a small button on the side of the circuit board.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 +
#Inside the battery compartment is a small button on the side of the circuit board.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Press the button 4 times to join the device to the Zigbee network.
 +
#The LED will flash in the following sequences:
 +
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 +
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 +
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
 +
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 +
#Inside the battery compartment is a small button on the side of the circuit board.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Motion Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NCZ-3041-HA</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Press the button 4 times to join the device to the Zigbee network.
 +
#The LED will flash in the following sequences:
 +
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 +
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 +
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
 +
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 +
#Inside the battery compartment at the top, is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Garage Door (Tilt) Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NCZ-3014-HA</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Press the button 4 times to join the device to the Zigbee network.
 +
#The LED will flash in the following sequences:
 +
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 +
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 +
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
 +
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Door/Window Sensor</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>NCZ-3011-HA</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Slide open the Door/Window Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Slide open the Door/Window Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Press the button 4 times to join the device to the Zigbee network.
 +
#The LED will flash in the following sequences:
 +
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 +
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 +
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
 +
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Slide open the Door/Window Sensor’s top housing.
 +
#Inside the battery compartment is a small button.
 +
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 +
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
 +
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
 +
 +
<hr />
 +
=='''<big>Orbit</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Orbit</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>Smart Hose Faucet Timer</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>27087</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Irrigation Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Insert two AA alkaline batteries and re-insert the tray.
 +
#Press the RESET button '''5 times''' in rapid secession.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Slide out the battery tray on the back of the timer.
 +
#Insert two AA alkaline batteries and re-insert the tray.
 +
#*'''NOTE:''' Firmly replace the battery tray to ensure water resistance and increase battery life. You will know the battery tray is fully inserted if it does not pull out easily.
 +
#Turn the dial to '''AUTO'''.
 +
#When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
 +
#*'''NOTE:''' The timer will remain in pairing mode for '''10 minutes or until paired.''' If pairing is not successful after 10 minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button 5 times in rapid secession.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the device details page to confirm proper operation.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#Press the RESET button '''5 times''' in rapid secession.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Orbit</big>'''</div>
 +
|<div style="text-align: center;">
 +
'''<big>12-Station Sprinkler Controller</big>'''
 +
</div>
 +
|<div style="text-align: center;">'''<big>27396</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Irrigation Controller</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Ensure the controller is connected to power.
 +
#Press the SYNC button '''5 times''' in rapid secession.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Ensure the controller is connected to power.
 +
#Turn the dial to '''AUTO'''.
 +
#When the controller is first connected to power, it will automatically attempt to connect.
 +
#*'''NOTE:''' If pairing is not successful after 10 minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button '''5 times''' in rapid succession
 +
#The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words '''SMART MODE''' will appear on the screen.
 +
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 +
#Watch the status in the <nowiki/>device details page to confirm proper operation
 +
 +
'''Leaving the Zigbee Netwo'''<nowiki/>'''rk'''
 +
 +
#From the device's detail<nowiki/>s page, select Remove Device, then Remove
 +
#Press the SYNC button 5 <nowiki/>times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for 5 seconds to cancel re-pairing.
 +
 +
<hr />
 +
 +
=='''<big>Orvibo</big>'''==
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Obvibo</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>SN11</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 +
|}
 +
'''Factory Reset'''
 +
 +
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 +
#This will disconnect the sensor from the Zigbee network.
 +
#Short-press the reset button and the '''Green light''' will flash slowly.
 +
#The sensor is now in pairing mode.
 +
 +
'''Join the Zigbee Network'''
 +
 +
#Remove the cover by rotating it counterclockwise
 +
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 +
#This will disconnect the sensor from the Zigbee network.
 +
#Short-press the reset button and the '''Green light''' will flash slowly.
 +
#The sensor is now in pairing mode.
 +
 +
'''Leaving the Zigbee Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 +
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 +
#This will disconnect the sensor from the Zigbee network.
 +
 +
<hr />
 
=='''<big>Radio Thermostat Company of America</big>'''==
 
=='''<big>Radio Thermostat Company of America</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"

Latest revision as of 00:28, 21 July 2019

Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See How to Build a Solid Z-Wave Mesh for further detail on methods of Exclusion.

ADT

Brand
Device
Product Number
Device Type
Protocol
ADT (Nortek)
Water Leak Detector
10016864C
Water Sensor
Zigbee

Factory Reset

  1. Remove the cover by rotating it counterclockwise
  2. Press and hold the Connect button for 5 seconds
  3. After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. Remove the cover by rotating it counterclockwise
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Press and hold the Connect button for 5 seconds
  4. After the button is released, the LED will blink quickly for a few seconds, go dark for a few seconds, then blink slowly to indicate it is in pairing mode

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

AduroSmart

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Door / Window Sensor
ERIA 81822
Contact Sensor
Zigbee

Factory Reset

  1. Use the provided pin to press and hold the reset button for 10 seconds.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Use the provided pin to press and hold the reset button for 10 seconds.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Dimmer Switch
ERIA 81825
Button Controller
Zigbee

Factory Reset

  1. Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Hold down the off (circle) button for 10 seconds until it blinks green 3 times.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Motion Sensor
ERIA 81823
Motion Sensor
Zigbee

Factory Reset

  1. Use the provided pin to press and hold the reset button for 10 seconds.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Use the provided pin to press and hold the reset button for 10 seconds.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Aeotec (Aeon Labs)

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Doorbell Gen5
ZW056
Doorbell
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Doorbell Gen5, and its LED will blink rapidly to indicate that it is communicating.
  3. If your Doorbell has been successfully linked to your network, its LED will become solid for 2 seconds, then stop. If linking was unsuccessful, the LED will blink when you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Doorbell.
  4. If your Doorbell has been successfully unlinked to your network, its LED will begin to blink slowly indicating it is ready to be paired to a new network..

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor 6
ZW112
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold Door Window Sensor 6 Action button
  2. Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
  3. If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Tap the button on the Door Window Sensor 6
  3. The LED will blink green to indicate successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your Door Window Sensor is successfully removed from the Z-Wave network, the RGB LED will become a colorful gradient for a few seconds and then turn off. If the removing was unsuccessful, the RGB LED will be solid for 8 seconds and then turn off, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor Gen5
ZW120
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once to include the door/window sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast blink for 8 seconds and then slow blink for 3 seconds when you press the Action Button again.
  5. If the removal was unsuccessful, the Status LED will fast blink for 2 seconds and then be solid for 2 seconds when you press the Action Button, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor Gen2
DSB29
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once to include the door/window sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor to exclude it from the network

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor 1E
DSB04100
Contact Sensor
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the sensor to a default state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
  3. The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the will be blinking while awake.
    • Note: The DSB04100 sensor can only be taught to communicate to devices within it’s own network.
    • If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
    • If the sensor was successfully included in the Z-Wave network, the LED will blink instead of staying solid.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Use an Aeon Z-Stick or Minimote to exclude the sensor from previous networks

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Garage Door Controller Gen5
ZW062
Garage Door Opener
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and release.
  2. Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave Button on the Garage Door Controller.
  3. The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on the Garage Door Controller.
  4. The LED on Garage Door Controller will blink rapidly, followed by a solid LED for 1-2 second for a successful exclusion.
  5. The Network LED on the Garage Door Controller should now be blinking slowly to indicate it is ready to be paired to a new network.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Dry Contact Sensor Gen5
ZW097
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Sensor.
  3. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear. If linking was unsuccessful, the LED will continue to blink if you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Aeon Labs Home Energy Meter
AEDSB09104ZWUS
Energy Meter
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 10 seconds.
  2. If successful, the LED on the HEM should begin to blink slowly.

Join the Z-Wave Network

  1. Remove the screw from the back of your Reader and open the battery cover.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for 1 second. If the linking was unsuccessful the light will blink after pressing your meter’s Action Button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the screw from the back of your Reader and open the battery cover.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. Press the Action Button (small black button under the battery tray) on your reader.If your Reader has been successfully removed from your network its light will blink for 1 second. If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Home Energy Meter Gen2 / Gen5
ZW095
Energy Meter
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 10 seconds.
  2. If successful, the LED on the HEM should begin to blink slowly.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to blink.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will blink. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb Gen5
ZW098
Bulb
Z-Wave

Factory Reset

  1. Removing LED Bulb from your Z-Wave network will reset LED Bulb to default factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch ON. LED Bulb’s green LED will blink to indicate that it is looking for a Z-Wave network to connect to.
  3. After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Turn LED Bulb’s wall switch on.
  4. Toggle LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if successful, the orange LED will be solid for 2 seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
  5. To confirm successful removal its color will change to orange for 2 seconds before changing to white. If removal was unsuccessful, LED Bulb will blink orange for 3 seconds before changing to red for 2 seconds.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb 6 Multi-Color
ZWA002
Bulb
Z-Wave

Factory Reset

  1. Turn LED Bulb’s wall switch on and wait 1 second.
  2. Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
  3. If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to 10 seconds.
  3. After successfully connecting to your network, LED Bulb will flash green -> white color for 3 seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
  4. LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for 3 seconds.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb 6 Multi-White
ZWA001
Bulb
Z-Wave

Factory Reset

  1. Turn LED Bulb’s wall switch on and wait 1 second.
  2. Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
  3. If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will blink 2x times to indicate that it is looking for a Z-Wave network to connect to.
  3. After successfully connecting to your network, LED Bulb will blink off then on in about half a second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Turn LED Bulb’s wall switch on and wait 1 second.
  4. Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
  5. LED Bulb 6 if successful will flash once, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Illuminator G2
DSC19103-ZWUS
Dimmer
Z-Wave

Factory Reset

  1. Hold the Z-Wave button for 30 seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for 30 seconds).

Join the Z-Wave Network

  1. Connect Micro Smart Dimmer to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the Z‐Wave button.
  4. If the inclusion fails, please repeat the process from step 2.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z‐Wave button.
  4. If the exclusion fails, please repeat the process from step 2

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Motor Controller
DSC14104-ZWEU/US, DSC14103-ZWAU
Motor Controller
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the controller to a default state.

Join the Z-Wave Network (Z-Stick)

  1. Connect Micro Motor Controller to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. Press the Action Button on your Micro Motor Controller.
  5. If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
  6. If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
  7. Press the Action Button on the Z-Stick to take it out of installation mode.

Join the Z-Wave Network (Minimote)

  1. Connect Micro Motor Controller to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the Include button on your Minimote.
  4. Press the Action Button on your Micro Motor Controller.
  5. If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
  6. If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
  7. Press any button on your Minimote to take it out of inclusion mode.

Exclusion from the Z-Wave Network (Z-Stick)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. Press the Action Button on your Micro Motor Controller.
  5. If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
  6. If the removal was unsuccessful, the Network LED will not blink.
  7. Press the Action Button on the Z-Stick to take it out of removal mode.

Exclusion from the Z-Wave Network (Minimote)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Remove Button on your Minimote.
  4. Press the Action Button on your Micro Motor Controller.
  5. If your Micro Motor Controller has been successfully removed from your network, its Network LED will blink.
  6. If the removal was unsuccessful, the Network LED will not blink.
  7. Press any button on your Minimote to take it out of removal mode.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Switch G2
DSC26 / DCS18
Switch
Z-Wave

Factory Reset

  1. Press and hold the button on the Micro Switch G2 for 20 seconds and then release it.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
  3. If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
  4. If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Minimote
DSA03202
Button Controller
Z-Wave

Factory Reset

  1. Pull down the panel on the  Minimote
  2. Press and hold the bottom 2 buttons down. The Red and Blue LED will alternate faster and faster.
  3. When both Red and Blue LED become solid, you may let go.

Include a device from the Z-Wave Network

  1. Tap the Inclusion (+) button, LED should be blinking blue
  2. Tap the button on the device you want to add
  3. After the LED stops flashing rapidly, tap any button to get out of inclusion mode

Exclusion a device from the Z-Wave Network

  1. Tap the Exclusion (-) button, LED should blink red
  2. Tap button on the device you want to remove
  3. After LED stops flashing rapidly, tap any button to get out of the exclusion mode

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Multisensor Gen5
ZW074
Motion Sensor
Z-Wave

Factory Reset

  1. Press and hold Multisensor Gen5 Action button (For 20 seconds)
  2. The LED of the Multisensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
  3. Release the Multisensor Gen5 Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave Button on your MultiSensor.
  3. You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
  4. If the LED blinks when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on your MultiSensor.
  4. If your MultiSensor has been successfully removed from your network, its LED will blink when you press the Z-wave Button.
  5. If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Multisensor 6
ZW100
Motion Sensor
Z-Wave

Factory Reset

  1. Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
  2. If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
  3. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your MultiSensor. The LED on Multisensor will blink Green rapidly, followed by a solid Green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
  3. You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
  4. If the green LED blinks when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your MultiSensor. The LED on Multisensor will blink red then change into a colorful gradient.
  4. If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will blink.
  5. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
NanoMote One
ZWA004
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the NanoMote button for 20 seconds.
  2. The LED will change from: Orange > Green > Red > Pink > Red
  3. Release the button on the second Red LED status. It will remain red for 2 seconds
  4. Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Double click the NanoMote button, the LED will blink rapidly with a white color.
  3. If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
  4. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
    • If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Double click the NanoMote button, the LED will become a solid green color.
  4. If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
NanoMote Quad
ZWA003
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the NanoMote button for 20 seconds.
  2. The LED will change from: Orange > Green > Red > Pink > Red
  3. Release the button on the second Red LED status. It will remain red for 2 seconds
  4. Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Double click the NanoMote button (can be any button), the LED will blink rapidly with a white color.
  3. If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
    • If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Double click the NanoMote button, the LED will become a solid green color.
  4. If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Dimmer
ZW111
Dimmer
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will blink to indicate the Nano Dimmer is entering into pairing mode.
  3. If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
  4. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Switch (with energy reading)
ZW116
Switch
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once on the Nano Switch.
  3. If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Switch (without energy reading)
ZW139
Switch
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once on the Nano Switch.
  3. If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Range Extender (Aeon Labs Z-Wave Network Repeater)
DSD37
Switch
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the Range Extender to a default state.

Join the Z-Wave Network (Z-Stick)

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Z-Stick.
  3. If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
  4. If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
  5. Press the Action Button on the Z-Stick to take it out of installation mode.

Join the Z-Wave Network (Minimote)

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Include button on your Minimote.
  3. If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer blink.
  4. If the linking was unsuccessful and the Network LED continues to blink repeat the above steps.
  5. Press any button on your Minimote to take it out of inclusion mode.

Exclusion from the Z-Wave Network (Z-Stick)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. If your Range Extender has been successfully removed from your network, its Network LED will blink.
  5. If the removal was unsuccessful, the Network LED will not blink.
  6. Press the Action Button on the Z-Stick to take it out of removal mode.

Exclusion from the Z-Wave Network (Minimote)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Remove Button on your Minimote.
  4. If your Range Extender has been successfully removed from your network, its Network LED will blink.
  5. If the removal was unsuccessful, the Network LED will not blink.
  6. Press any button on your Minimote to take it out of removal mode.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Range Extender 6
ZW117
Repeater
Z-Wave

Factory Reset

  1. Press and hold the Z-Wave Button for 20 seconds to completely factory reset your Range Extender 6.
  2. During the time that you are holding your Range Extender 6 action button down, the LED will blink through these colors: Yellow (at 2 seconds) > Purple (at 5 seconds) > Red for 8 seconds (initializing factory reset) > Green for 20 seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
  3. You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will blink green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
  3. If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for 2 seconds then turn off. If the adding was unsuccessful, the red LED will be on for 2 seconds and then remain colorful gradient status, repeat the steps above.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on your Range  Extender.
  4. If Range Extender has been successfully removed  from your network, its RGB LED will remain colorful gradient status.
  5. If the removal was unsuccessful, the RGB LED will still be solid, repeat the steps above.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Recessed Door Sensor Gen5
ZW089
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it. Your sensor will now be reset to its original settings

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear.
  3. If linking was unsuccessful, the LED will continue to blink if you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to blink for a short time.
  4. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Siren
ZW080
Siren
Z-Wave

Factory Reset

  1. Press and hold the Action button for 20 seconds
  2. At 8 seconds, the Siren will sound for 1 second, then stop
  3. The LED will continue to blink faster and faster and then will then turn solid for 2 seconds to indicate a successful factory reset
  4. You may let go of its Action button, and the Siren Gen5 factory reset is complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Siren Gen5, and its LED will blink rapidly to indicate that it is communicating.
  3. If your Siren has been successfully linked to your network, its LED will become solid for 2 seconds, then stop.
  4. If linking was unsuccessful, the LED will blink when you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Siren.
  4. If your Siren has been successfully unlinked from your network, its LED will begin to blink.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Smart Switch 6
ZW096
Switch
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds.
  2. The LED will change between these colors: Yellow > Purple > Red (blinks faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
  3. When the LED changes to Green state, you may let go of the action button.
  4. When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your Switch once and the LED will flash a green LED.
  3. If your switch has been successfully linked to your network, its LED will become solid green for 2 seconds.
  4. If linking was unsuccessful, the LED will return to a rainbow gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Switch.
  4. If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
  5. If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
TriSensor
ZWA005
Motion Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 15 seconds.
  2. The red LED flashes to confirm a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button on your sensor once.
  3. The LED will turn yellow LED for 10 seconds.
  4. If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your sensor.
  4. The LED will turn purple for 2 seconds, and then white when exclusion is successful.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
WallMote Quad
ZW129
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the Action button (20 seconds).
  2. The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
  3. Let go of the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once on WallMote Quad to include it.
  3. The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your WallMote Quad.
  4. If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
WallMote Quad
ZW130
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the Action button (20 seconds).
  2. The LED should blink between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
  3. Let go of the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Action Button once on WallMote Quad to include it.
  3. The green LED will be on for 2 seconds and then the orange LED will fast blink for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your WallMote Quad.
  4. If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.

August

Brand
Device
Product Number
Device Type
Protocol
August
Smart Lock Pro
ASL-03
Lock
Z-Wave

Factory Reset

  1. You must have your lock first connected to the August App
  2. Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
    • My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
    • My Hub is No Longer Working - use this mode to RESET the Device.
  3. Select the My Hub is No Longer Working option and then select Reset Z-Wave Device.

Join the Z-Wave Network

  1. You must have your lock first connected to the August App
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. On the August App, go into Lock Settings and door for Z-Wave Settings.
  4. The first time the screen will state that "The Lock is not connected to a Z-Wave Network". Select "Add to a Z-Wave Network".
  5. Follow the instructions to put the lock into Learn Mode.

Exclusion from the Z-Wave Network

  1. You must have your lock first connected to the August App
  2. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device.
  5. Select Remove Z-Wave Device and on the next page you will see two options.
    • My Hub is in Exclusion Mode - Use this mode when you have a working hub and can properly disconnect.
    • My Hub is No Longer Working - Use this mode to RESET the Device.
  6. Select the My Hub is in Exclusion Mode option to exclude the lock from the Z-Wave network.

BeSense

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave PLUS Ceiling PIR Sensor
IX32
Motion Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave Plus Window/Door Sensor
IM20
Contact Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave PIR Sensor
IX30
Motion Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

Centralite

Brand
Device
Product Number
Device Type
Protocol
Centralite
Pearl Thermostat
3000-G
Thermostat
Zigbee

Factory Reset

  1. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  2. The device will then factory reset itself and begin looking for an open network to join.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  3. The device will then factory reset itself and begin looking for an open network to join.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Smart Outlet
3200-G
Outlet
Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Door & Window Sensor
3300-G
Contact Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Motion Sensor
3305-G
Motion Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Micro Door Sensor
3323-G
Contact Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Micro Motion Sensor
3328-G
Motion Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
4-Series Smart Outlet
4200-C
Outlet
Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  4. After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

CREE

Brand
Device
Device Type
Protocol
CREE
Connected LED Bulbs
Bulb
Zigbee

Factory Reset

  1. Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
  2. The bulb will blink once, indicating it is reset and ready for pairing

Factory Reset (Alternate Method)

  • Method 1 - Use a Philips Hue Dimmer Switch
  1. Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
  2. Hold the remote within 4 inches of the bulb.
  3. Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts blinking on and off.
  4. If the bulb stopped blinking (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) blinked green - your bulb is reset.
    • This method can be used for nearly ALL ZigBee LL bulbs.
  • Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)
  1. Hold the remote within 4 inches of the bulb.
  2. Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
  3. The bulb should blink on and off
  4. The green LED on the remote should come on and may blink a few times.
  5. Continue to hold both buttons on the remote until the green LED goes off completely.
    • This method can be used for nearly ALL ZigBee LL bulbs.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
  3. The bulb will blink once, indicating it is reset and ready for pairing

Join the Zigbee Network (Alternate Method)

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. See Factory Reset (Alternate Method) above to reset the bulb and put it into pairing mode.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Dome

Brand
Device
Product Number
Device Type
Protocol
Dome
Door / Window Sensor
DMWD1
Contact Sensor
Z-Wave

Factory Reset

  1. Open the Cover and make sure the Door/Window Sensor is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the Cover of the Door/Window Sensor.
  3. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the Cover of the Door/Window Sensor.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Door / Window Sensor
DMDP1
Contact Sensor
Z-Wave

Factory Reset

  1. Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
  2. Wait for 5 seconds.
  3. Move the Magnet and Sensor Base in and out of the closed position 6 times.
  4. The LED indicator will light up red for five seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the Sensor Cover and the LED indicator will start blinking yellow.
  3. Press the Button quickly 3 times in a row.
  4. The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green three times then blink red until the cover is replaced.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the SENSOR COVER and the LED indicator will start blinking red.
  4. Press the Button quickly 3 times in a row.
  5. The LED Indicator will flash green three times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.

Brand
Device
Product Number
Device Type
Protocol
Dome
Leak Sensor
DMWS1
Water Sensor
Z-Wave

Factory Reset

  1. Open the Back Plate and make sure the Leak Sensor is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the cover of the Leak Sensor by twisting it apart.
  3. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the cover of the Leak Sensor by twisting it apart.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Leak Sensor
DMMS1
Water Sensor
Z-Wave

Factory Reset

  1. Remove the Cover and make sure the Motion Detector is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator blinks once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the cover of the Motion Detector by twisting it apart.
  3. Press the Connect Button quickly 3 times in a row.
  4. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Mouser
DMMZ1
Mouse Trap
Z-Wave

Factory Reset

  1. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  2. Press and hold the CONNECT BUTTON for at least 10 seconds then release.
  3. A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  3. Press the CONNECT BUTTON quickly 3 times in a row.
  4. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  4. Press the CONNECT BUTTON quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
On/Off Plug-In Switch
DMOF1
Switch
Z-Wave

Factory Reset

  1. Plug in the On/Off Plug-In Switch.
  2. Hold the Connect Button for 10 seconds until the LED Indicator blinks once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Range Extender
DMEX1
Repeater
Z-Wave

Factory Reset

  1. Hold the Button for 10 seconds until the LED blinks 10 times, then release the button

Join the Z-Wave Network

  1. For proper inclusion, install the Range Extender in the final location where it will be used.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash 5 times indicating successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Button quickly 3 times in a row The LED will flash 5 times indicating successful exclusion.

Brand
Device
Product Number
Device Type
Protocol
Dome
Siren
DMS01
Siren
Z-Wave

Factory Reset

  1. Open the Back Plate and make sure the Siren is powered.
  2. Hold the Connect Button for 10 seconds until the LED Ring blinks once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the Back Plate of the Siren.
  3. Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the Back Plate of the Siren.
  4. Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Water Main Shut-Off
DMWV1
Shutoff Valve
Z-Wave

Factory Reset

  1. Press and hold the open/close button for at least 10 seconds then release.
  2. The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly 3 times in a row. The LED will stop blinking and stay on continuously upon successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.

Dragon Tech

Brand
Device
Product Number
Device Type
Protocol
Dragon Tech
Plug in Z-Wave Plus Dimmer Switch
PD-100
Dimmer
Z-Wave

Factory Reset

  1. Unplug the PD-100 and anything the is plugged into it.
  2. Press and hold the button on the front of the PD-100
  3. Plug the PD-100 in while still pressing the button
  4. After 3 seconds, release the button. If the button blinks, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the button on the front of the PD-100

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the button on the front of the PD-100

Eaton (Cooper Wiring Devices)

Brand
Device
Product Number
Device Type
Protocol
Eaton
Wireless Dimmer
RF9540
Dimmer
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.

Join the Z-Wave Network

  1. Cooper Wiring Devices Z-Wave device has a blue LED, which will blink when the device is not included in a Z-Wave network. The LED stops blinking when the device is in a network.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the device switch one time to include it in the network. The LED will stop blinking, indicating the dimmer has been successfully included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the device switch one time to exclude it from the network. The LED will start blinking, indicating the dimmer has been successfully excluded from the Z-Wave network.

Ecolink

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Door / Window Sensor
DWZWAVE2.5-ECO
Contact Sensor
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Flood/Freeze Sensor
FLF-ZWAVE5
Water Sensor
Z-Wave Plus

Factory Reset

  1. The Flood Freeze sensor factory defaults on network exclusion
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for 1 second, then reinstall it.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the battery for at least 10 seconds, then reinstall it.
  3. If the LED starts blinking continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.
  4. If after 5 seconds the LED is not blinking, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the Flood Freeze case and remove the battery for 1 second.
  4. Replace the battery and the device should be removed from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Motion Sensor with Pet Immunity
PIR-ZWAVE2.5
Motion Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Siren
SC-ZWAVE5
Siren
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  4. The LED on the front of the unit will turn off if successful exclusion from the network.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  4. The LED on the front of the unit will turn off if successful exclusion from the network.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
FireFighter
FF-ZWAVE5
Smoke/CO Detector
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the FireFighter case and press the learn button on the device for one second.
  4. If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Open the FireFighter case and press the learn button on the device for one second.
  3. If the LED starts blinking continually, the sensor has not been added. Repeat the steps.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the FireFighter case and press the learn button on the device for one second.
  4. If successfully removed from the Z-Wave Plus network, the devices Green LED should blink slowly continuously

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch
DLS-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch Double Toggle
DTLS2-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch Dual Rocker
DDLS2-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Tilt Sensor
TILT-ZWAVE2
Tilt Sensor
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Tilt Sensor
TILT-ZWAVE2.5
Tilt Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will blink for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Toggle Light Switch
TLS-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Enerwave

Brand
Device
Product Number
Device Type
Protocol
Enerwave
Ceiling Mounted PIR Motion Sensor
ZWN-BPC-Plus
Motion Sensor
Z-Wave Plus

Factory Reset

  1. To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the inclusion/exclusion button on the sensor 3 times.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion/exclusion button on the sensor 3 times.

Everspring

Brand
Device
Product Number
Device Type
Protocol
Everspring
Door/Window Detector
HSM02
Contact Sensor
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED will be steady on.
  2. Within 1 second, press and hold the tamper switch until LED is off.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Flood Detector
ST812
Water Sensor
Z-Wave

Factory Reset

  1. Press link key three times within 1.5 second. The sensor will beep each time the link key is pressed.
  2. Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Pressing link key three times within 1.5 second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing link key three times within 1.5 second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.

Brand
Device
Product Number
Device Type
Protocol
Everspring
PIR Detector
HSP02
Motion Sensor
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED will be steady on.
  2. Within 1 second, press and hold the tamper switch until LED is off.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second will enter exclusion mode.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Photoelectric Smoke Alarm
SF-813
Smoke Detector
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED flashes and the buzzer sounds when the link key is pressed.
  2. Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
  3. The LED will light for 5 seconds and the buzzer will sound for 5 seconds

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
  3. The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
  4. The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
  4. The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
  5. The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has been excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Temperature/Humidity Detector
SF-814
Temperature Sensor
Z-Wave

Factory Reset

  1. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
  2. Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
  3. When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
  4. When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks

Evolve

Brand
Device
Product Number
Device Type
Protocol
Evolve
Isolated Contact Fixture Module
LFM-20
Relay
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Exclude the module by tapping the button three times, then press and hold for 10 seconds.
    • LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the button on the once to include it in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Exclude the module by tapping the button three times, then press and hold for 10 seconds.
    • LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.

Fibaro

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Button
FGPB-101
Outlet
Z-Wave

Factory Reset

  1. Click the Button exactly five times.
  2. Press and hold the Button for at least 5 seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Click the button at least 6 times.
  3. Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
  4. Click the button 4 times to wake it up
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Click the Button at least six times.
  4. Wait for the removing process to end.
  5. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Door/Window Sensor 2
FGDW-002
Contact Sensor
Z-Wave

Factory Reset

  1. Open the cover and remove the battery.
  2. Install the battery while holding both TMP buttons.
  3. The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
  4. Release one button when the LED indicator starts flashing quickly.
  5. Click the released button once to confirm initiation of the reset procedure.
  6. Wait a few seconds for a long blink of the LED indicator. Do not remove the battery.
  7. The LED indicator will blink 5 times quickly to confirm reset of the device.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press one of the TMP buttons quickly, three times in a row, while keeping other button is pressed.
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press one of the TMP buttons quickly, three times in a row, while keeping other button is pressed.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Flood Sensor
FGFS-101 FG3
Water Sensor
Z-Wave

Factory Reset

  1. Make sure the sensor is powered.
  2. Press and hold the TMP button.
  3. Wait for the visual LED indicator to glow yellow (4th position of the MENU).
  4. Release the TMP button.
  5. Click the TMP button once to confirm selection.
  6. After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Removed the battery for 10 seconds, and re-install it
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the TMP button quickly, three times in a row.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Flood Sensor ZW5
FGFS-101 ZW5
Water Sensor
Z-Wave Plus

Factory Reset

  1. Make sure the sensor is powered.
  2. Press and hold the TMP button.
  3. Wait for the visual LED indicator to glow yellow (4th position of the MENU).
  4. Release the TMP button.
  5. Click the TMP button once to confirm selection.
  6. After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the TMP button quickly, three times in a row.
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the TMP button quickly, three times in a row.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
KeyFob
FGKF-601 ZW5
Button Controller
Z-Wave Plus

Factory Reset

  1. Click O and simultaneously.
  2. Click or X until LED is Yellow - reset the device.
  3. Click + to confirm selection, or is you do not wish to reset at this time, click to exit the menu.
  4. The LED will pulse Yellow twice to confirm the device has been reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. LED will pulse White during the adding process.
  3. Wait for the inclusion process to end.
  4. Successful adding will be confirmed by the Z-Wave controller’s message.
  5. Successful inclusion will be confirmed by Hubitat Elevation™ and the remote LED will be Green.
  6. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Click O and simultaneously.
  4. Click or X until LED is Green.
  5. Click + to confirm selection.
  6. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Motion Sensor ZW5
FGMS-001 ZW5
Motion Sensor
Z-Wave Plus

Factory Reset

  1. Open the cover
  2. Press and hold the B-button.
  3. Wait for visual indicator to glow Yellow (2nd menu position).
  4. Release the B button and then briefly click the B-button to confirm selection
  5. After few seconds the device will be reset, which is signaled with the red, fading visual indicator color.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the B button quickly, three times in a row.
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the B button quickly, three times in a row.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
RGBW Controller
FGRGBW-101
RGBW Controller
Z-Wave

Factory Reset

  1. Disconnect the supply voltage.
  2. Press and hold the B button located inside the RGBW Controllers casing.
  3. Connect the the supply voltage, while still holding the B button.
  4. Release the B button.
  5. The B channel will turn on (blue channel).
  6. Disconnect the power supply.

Join the Z-Wave Network

(Auto Inclusion)

  1. Make sure the RGBW Controller is not connected to a supply.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Connect voltage supply to auto-include the RGBW Controller.
  4. The RGBW Controller will be automatically recognized and included in the Z-Wave network.
  5. Successful inclusion will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

(Manual Inclusion)

  1. Make sure the RGBW Controller is not connected to a supply.
  2. To disable auto-inclusion press the B button briefly, after re-connecting the RGBW Controller to its supply voltage.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  4. Triple click the B button or any switch connected to I1-I4 inputs.
  5. The RGBW Controller will be recognized and included in the Z-Wave network.
  6. Successful inclusion will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Triple click the B button or any switch connected to I1-I4 inputs.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Single Switch 2
FGS-213
Switch
Z-Wave Plus

Factory Reset

  1. Switch off the mains voltage (disable the breaker).
  2. Remove the Switch 2 from the wall switch box.
  3. Switch on the mains voltage.
  4. Press and hold the B button to enter the menu until the visual LED indicator is Yellow.
  5. Quickly release and click the B button again.
  6. After few seconds the device will be restarted, which is signaled by the Red LED indicator color.

Join the Z-Wave Network

  1. Identify the S1 switch.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Quickly, three times press the S1 switch.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, three times press the S1 switch.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Wall Plug
FGWPB-111 / FGWPB-121
Outlet
Z-Wave Plus

Factory Reset

  1. Make sure the device is powered.
  2. Press and hold the button.
  3. Wait for the LED frame to glow yellow (3rd menu position).
  4. Release the button and then briefly click the button once to confirm the selection.
  5. After few seconds the device will restart with factory settings, which is signaled with the red frame color.

Join the Z-Wave Network

  1. Plug the device into a socket.
  2. The LED frame will glow red signaling it has not being added (If is doesn't you must first perform a general exclusion and then a factory reset).
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  4. Quickly, triple click the button located on the casing.
  5. Successful inclusion will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. Plug the device into a socket.
  3. Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
  5. Quickly, triple click the button located on the casing.
  6. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Wall Plug
FGWPE-102
Outlet
Z-Wave

Factory Reset

  1. Press and hold the button located on the side.
  2. The device will cycle through GREEN, then VIOLET, and finally YELLOW for device reset.
  3. Release the button.
  4. Press the button again to confirm the selection and factory reset the device.

Join the Z-Wave Network

  1. Plug the device into a socket nearby the main Z-Wave controller.
  2. The LED frame will glow red signaling not being added (reset or remove the device otherwise).
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  4. Quickly, triple click the button on the side of the device.
  5. The device will be included to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple click the button on the side of the device.
  4. Plug the device into a socket nearby the main Z-Wave controller.
  5. The LED frame will glow green signaling being added (removing is not necessary otherwise).
  6. Quickly, triple click the button on the side of the device.
  7. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Dimmer 2
FGS-212
Switch
Z-Wave Plus

Factory Reset

  1. Switch off the mains voltage (disable the breaker).
  2. Remove the Dimmer 2 from the wall switch box.
  3. Switch on the mains voltage.
  4. Press and hold the B button to enter the menu until the visual LED indicator is Yellow.
  5. Quickly release and click the B button again.
  6. After few seconds the device will be restarted, which is signaled by the Red LED indicator color.
  7. The device enters the calibration mode.

Join the Z-Wave Network

  1. Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing).
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Quickly press switch no. 1 or the B button three times.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. Identify the S1 switch on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly press switch no. 1 or the B button three times.
  4. The device will be excluded from the Z-Wave network.
  5. Dimmer 2 will start the calibration process

First Alert

Brand
Device
Product Number
Device Type
Protocol
First Alert
Smoke & Carbon Monoxide Combo Alarm
ZCOMBO-G
Smoke / CO Detector
Z-Wave

Factory Reset

  1. Power up the device with the test button held down for 10+ seconds
  2. The device will reset all Z-Wave settings and leave the network. NOTE: The device will not remain awake after resetting and will go into standby mode.

Join the Z-Wave Network

  1. Slide battery door open and insert batteries.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Slide battery door open, then remove and re-insert batteries.
  4. Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.

GE/Jasco

Brand
Device
Product Number
Device Type
Protocol
GE
Link Bulb
Bulb
Zigbee

Factory Reset

  1. Turn OFF the light for 3 second.
  2. Turn ON the light for 3 seconds
  3. Repeat this process 5 times
  4. The bulb will dim and then flash once when successfully reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Turn the bulb on.
  3. The bulb will flash when connected to the hub.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Plug-in Dimmer
12718
Dimmer
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Single press and release the manual/program button on the device to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Plug-in Switch
12719/ZW4101
Switch
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Single press and release the manual/program button on the device to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Outdoor Plug-in Switch
12720/ZW4201
Switch
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Single press and release the manual/program button on the device to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Outlet
12721
Outlet
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Single press and release the manual/program button on the device to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Switch
12722
Switch
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Dimmer
12724
Dimmer
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Toggle Switch
12727
Switch
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press up and release the toggle switch to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press up and release the toggle switch to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press up and release the toggle switch to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Toggle Dimmer
12729
Dimmer
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press up and release the toggle switch to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press up and release the toggle switch to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press up and release the toggle switch to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Fan Control
12730/ZW4002
Fan Controller
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
    • 12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless fan control rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Plug-In Outdoor Switch
14284
Switch
Z-Wave Plus

Factory Reset

  1. Unplug the switch from the outlet
  2. Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Fan Control
14287
Fan Controller
Z-Wave Plus

Factory Reset

  1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
  2. The LED will flash ON/OFF 5 times when completed successfully.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless fan control rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
    • Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Tamper Resistant Outlet
14288
Outlet
Z-Wave Plus

Factory Reset

  1. Press the manual/program button 3 times, then press and hold the button for at least 3 seconds. The LED will blink 5 times to confirm.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Switch
14291
Switch
Z-Wave Plus

Factory Reset

  1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
  2. The LED will flash ON/OFF 5 times when completed successfully.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart switch rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
    • Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Dimmer
14294
Dimmer
Z-Wave Plus

Factory Reset

  1. Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
  2. The LED will flash ON/OFF 5 times when completed successfully.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
    • Note: While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Smart Motion Switch
26931
Switch
Z-Wave Plus

Factory Reset

  1. Press and release the top button 10 times within five seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom button on the smart switch to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top or bottom button on the smart switch to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Smart Motion Switch
26933
Switch
Z-Wave Plus

Factory Reset

  1. Press and release the top button 10 times within five seconds. The LED will flash 3 times quickly confirming change

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the top or bottom button on the smart switch to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the top button on the smart switch to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Plug-in Dimmer
28167
Dimmer
Z-Wave Plus

Factory Reset

  1. If plugged in, unplug the Dimmer from the receptacle.
  2. Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Plug-in Dimmer
28169
Dimmer
Z-Wave Plus

Factory Reset

  1. If plugged in, unplug the Dimmer from the receptacle.
  2. Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the manual/program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the manual/program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
Hinge Pin Smart Door Sensor
32563/ZW6301
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and release the program button ten times quickly.
  2. The LED light will blink approximately eight times.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Single press and release the program button on the device to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Single press and release the program button on the device to exclude it from the network.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Switch
45856
Switch
Zigbee

Factory Reset

  1. Tap the top of the rocker (ON Switch) 10x quickly (short presses)

Join the Zigbee Network

  1. Remove power from the dimmer at the circuit breaker.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Restore power to the Smart Dimmer at the circuit breaker
  4. Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
  5. After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
    • Note: LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
GE/Jasco
In-Wall Dimmer
45857
Dimmer
Zigbee

Factory Reset

  1. Lift the air-gap switch at the bottom of the rocker to OFF position to power down the device.
  2. Hold down the UP button
  3. Push In the air-gap switch to ON position to power up the device.
  4. Release the UP button within 4 seconds of power up.

Join the Zigbee Network

  1. Remove power from the dimmer at the circuit breaker.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Restore power to the Smart Dimmer at the circuit breaker
  4. Pairing Begins Automatically: LED Status Indicator Blinks as the Smart Dimmer automatically scans for a compatible network controller to pair with.
  5. After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop blinking and the Smart Dimmer.
    • Note: LED Status Indicator stops blinking if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

GoControl

Brand
Device
Product Number
Device Type
Protocol
GoControl
Garage Door Controllers
GD00Z
Garage Door Opener
Z-Wave

Includes Linear GD00Z-2, GoControl GD00Z-4, Linear GD00Z-5, ADT GD00Z-6, GoControl GD00Z-7 and NuTone ND00Z

Factory Reset

  1. Reset the controller by pressing the Link button 5 times.
  2. A quick beep followed by a longer beep will indicate proper reset of the GD00Z series or ND00Z.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and release the Link button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and release the Link button.

Brand
Device
Product Number
Device Type
Protocol
GoControl
Door / Window Sensor
WADWAZ-1
Contact Sensor
Z-Wave

Factory Reset

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  2. Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.

Join the Z-Wave Network

  1. Unscrew the screw fastening the rear cover and slide the rear cover down
  2. Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the sensor has not yet performed inclusion with the controller.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  4. Once Hubitat Elevation™ discovers the device, the LED will stop blinking. If the LED does not stop blinking and is not discovered by your hub, relocate the WADWAZ-1 to within 100 feet (line of sight) of a Z-Wave repeater or your hub and restart Z-Wave pairing.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.

Graber

Brand
Device
Product Number
Device Type
Protocol
Graber
Motorized Shades
Shade
Z-Wave

Network Reset

  1. Press and hold the button on the headrail end cap for 7 seconds or until the shade jogs once.
  2. Release the button.
    • NOTE: The will not reset the shade limits

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash Green.
  3. Release the button.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash Green.
  4. Release the button
  5. The shade will be excluded from the Z-Wave network.

Halo Labs

Brand
Device
Product Number
Device Type
Protocol
Halo
Halo+
LS001A
Smoke/CO Detector
Zigbee

Factory Reset

  1. To reset, hold down center button for approximately 20+ seconds.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Once Halo greets you, it will automatically begin searching for a ZigBee network. Halo will glow for a couple minutes before timing out.
    • To awaken the detector, double-tap the center button or hold the button for approximately 3+ seconds.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Hold down the center button for approximately 20+ seconds. Halo will reset all ZigBee settings and leave the network. .

Hampton Bay

Brand
Device
Product Number
Device Type
Protocol
Hampton Bay
Wink Enabled Ceiling Fan Controller
MR101Z
Fan Controller
Zigbee

Factory Reset

  1. Turn off your fan for 3 seconds, then turn it on for 3 seconds (Repeat 5 times)
  2. The light will flash three times when the factory reset is successful.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Turn on your fan.
  3. When successful, the fan will turn on at low speed and the light will flash three times.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the controller

Hank

Brand
Device
Product Number
Device Type
Protocol
Hank
One-Key Scene Controller
HKZW-SCN01
Button Controller
Z-Wave Plus

Factory Reset

  1. Press and holding the center "Z-button" for 20 seconds.
  2. Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
  3. Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Insert the battery.
  3. Triple click the center "Z-button".
  4. If inclusion is successful, the LED will blink blue for less than 5 seconds, and then it will remain solid for 15 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If exclusion is successful, the LED will blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.

Brand
Device
Product Number
Device Type
Protocol
Hank
Four-Key Scene Controller
HKZW-SCN04
Button Controller
Z-Wave Plus

Factory Reset

  1. Press and holding the center "Z-button" for 20 seconds.
  2. Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
  3. Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Insert the battery.
  3. Triple click the center "Z-button".
  4. If inclusion is successful, the LED will blink blue for less than 5 seconds, and then it will remain solid for 15 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If exclusion is successful, the LED will blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.

Brand
Device
Product Number
Device Type
Protocol
Hank
RGBW LED Bulb
HKZW-RGB01
Bulb
Z-Wave Plus

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle power to the bulb off and on 3 times quickly.
  4. Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
  5. If the exclusion is successful, the RGB BULB will quicly blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
  6. The bulb will remain warm white after the exclusion procedure is complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Make sure power to the bulb is disconnected and the RGB BULB is close to the hub.
  3. Insert the bulb into a socket and then turn it on.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle power to the bulb off and on 3 times quickly.
  4. Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
  5. If the exclusion is successful, the RGB BULB will quicly blink orange for less than 5 seconds, and then it will remain solid for 3 seconds.
  6. The bulb will remain warm white after the exclusion procedure is complete.

HomePro

Brand
Device
Product Number
Device Type
Protocol
HomePro
Exterior Appliance Module
ZRP110
Outlet
Z-Wave

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Tap the button on the front of the module once

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Tap the button on the front of the module once

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Tap the button on the front of the module once

Homeseer

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Indicator Light Sensor
HS-FS100-L+
Light Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the Z-Wave button inside the sensor body for 10 seconds
  4. If successful, the LED will flash 5 times.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Perimeter Water Sensor
HS-FS100-W+
Water Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the Z-Wave button inside the sensor body for 10 seconds
  4. If successful, the LED will flash 5 times.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Wall Dimmer
HS-WD200+
Dimmer
Z-Wave Plus

Factory Reset

  1. Turn dimmer on by tapping the top of the paddle once.
  2. Quickly tap top of the paddle 3 times.
  3. If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Wall Switch
HS-WS200+
Switch
Z-Wave Plus

Factory Reset

  1. Turn dimmer on by tapping the top of the paddle once.
  2. Quickly tap top of the paddle 3 times.
  3. If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Door/Window Sensor
HS-DS100+
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Z-Wave button inside the sensor body for 20 seconds, the LED will stay on until the button is released.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
  3. If successful, the sensor body LED will blink briefly and then stay on for 3 seconds.
  4. If unsuccessful, the LED with blink briefly and then turn off. Should this happen, repeat the inclusion process.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Triple-click the Z-Wave button inside the sensor body.
  4. If successful, the LED will turn off within 1 second.
  5. If unsuccessful, the LED with blink for 5 seconds. Should this happen, repeat the exclusion process.

Brand
Device
Product Number
Device Type
Protocol
Homeseer
Leak Sensor
HS-LS100+
Water Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Z-Wave button for 20 seconds. Release the button once the LED stops blinking and glows solidly

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Click the Z-Wave button inside the sensor body once and wait for the process to finish.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Triple-click the Z-Wave button inside the sensor body. Wait for the inclusion process to finish.

IKEA

Brand
Device
Product Number
Device Type
Protocol
IKEA TRÅDFRI
Warm White Bulb
1000 lm Warm White
Bulb
Zigbee

Factory Reset

  1. Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
  2. Wait for at least 10 seconds after reset is complete before attempting to pair the bulb.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has successfully joined the Zigbee network.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
  3. Wait for at least 10 seconds after reset is complete before attempting to pair the bulb again.

Brand
Device
Product Number
Device Type
Protocol
IKEA TRÅDFRI
Outlet
Outlet
Zigbee

Factory Reset

  1. Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
  2. Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
  3. The LED will pulse quickly and then pulse slowly when you release the internal button.
  4. Wait for at least 10 seconds after reset is complete before attempting to pair the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
  3. Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
  4. The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
  3. Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
  4. The LED will pulse quickly and then pulse slowly when you release the internal button.
  5. Wait for at least 10 seconds after reset is complete before attempting to pair the device again.

Brand
Device
Product Number
Device Type
Protocol
IKEA TRÅDFRI
Signal Repeater
Repeater
Zigbee

Factory Reset

  1. Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
  2. Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
  3. An LED will pulse quickly and then pulse slowly when you release the internal button.
  4. Wait for at least 10 seconds after reset is complete before attempting to pair the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
  3. Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
  4. The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
  5. The signal repeater will pair as Device. No driver will be assigned and it is not nessecary to have one since this device only repeats Zigbee radio signals.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
  3. Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
  4. The LED will pulse quickly and then pulse slowly when you release the internal button.
  5. Wait for at least 10 seconds after reset is complete before attempting to pair the device again.

Inovelli

Brand
Device
Product Number
Device Type
Protocol
Inovelli
In-Wall Switch
Switch
Z-Wave Plus

Factory Reset

  1. Hold the UP button for 5 seconds when powered on

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Top button on the switch 6 times within 2 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Top button on the switch 6 times within 2 seconds.

Brand
Device
Product Number
Device Type
Protocol
Inovelli
Outlet
Outlet
Z-Wave Plus

Factory Reset

  1. Press and hold the top button for at least 3 seconds while you plug the outlet into a recepticle

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Once the controller is ready to include your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Once the controller is ready to exclude your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.

Brand
Device
Product Number
Device Type
Protocol
Inovelli
Switch Module
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is acomplished by performing a general exclusion on the device.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the center button 5 times within 1 second to exclude it in the Z-Wave network.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the center button 5 times within 1 second to include it in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the center button 5 times within 1 second to exclude it in the Z-Wave network.

IRIS

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Button

BTN900

Button
Zigbee

Factory Reset

  1. Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
  2. Remove the battery for at least 10 seconds. Reinsert the battery.
  3. Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
  4. Upon a successful reset, the smart button will blink green indicating the device is now ready to pair.
    • NOTE: The green light can be dim, if you're in a well lighted area this light could be difficult to see.
  5. If your button does not blink green check your battery, then retry from step 2.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. With the smart button, squeeze the two sides together by the ridges and gently pull them apart to reveal the battery compartment.
  4. Remove and re-insert the battery. When the smart button begins looking for your hub, the light around the button will blink green.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
  3. Remove the battery for at least 10 seconds. Reinsert the battery.
  4. Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
  5. Upon a successful reset, the smart button will blink green indicating the device is now ready to pair.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  6. If your button does not blink green check your battery, then retry from step 2.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Care Pendant

PDT900

Button Controller
Zigbee

Factory Reset

  1. Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
  2. Remove the battery for at least 10 seconds. Reinsert the battery.
  3. Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to blink.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Insert the supplied access tool into the small opening at the top of the pendant. Gently pry open the case to reveal the battery compartment.
  4. Insert the battery in the correct orientation. The pendant will light up and start blinking as it begins searching for your hub
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
  3. Remove the battery for at least 10 seconds. Reinsert the battery.
  4. Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to blink.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Door/Window Sensor

DWS800

Contact Sensor
Zigbee

Factory Reset

  1. Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
  2. Reinsert the battery and immediately press the white reset button 8 times.
  3. Your Iris Contact Sensor should now be blinking green indicating it's ready to pair
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. On the large piece, remove the back by squeezing the semi-circles on either side.
  4. The sensor's LED will blink while searching for the hub.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
  3. Reinsert the battery and immediately press the white reset button 8 times.
  4. Your Iris Contact Sensor should now be blinking green indicating it's ready to pair
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Keyfob

KEY903

Presence Sensor
Zigbee

Factory Reset

  1. Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
  2. Remove the battery for at least 10 seconds. Reinsert the battery.
  3. Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to blink.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
  4. Insert the battery in the correct orientation. The fob will light up and start blinking as it begins searching for your hub.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
  3. Remove the battery for at least 10 seconds. Reinsert the battery.
  4. Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to blink.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Motion Sensor

MOT800

Motion Sensor
Zigbee

Factory Reset

  1. Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
  2. Remove the battery for at least 10 seconds. Reinsert the battery.
  3. As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. On the large piece, remove the back by squeezing the raised edges on both sides.
  4. Insert the battery. The sensor's LED will blink while searching for the hub.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
  3. Remove the battery for at least 10 seconds. Reinsert the battery.
  4. As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to blink. (You may have to make a shadow over the device to see the blinking light). Once the light is blinking you're ready to pair.
    • NOTE: The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V1 Smart Plug

SPG800

Outlet
Zigbee

Factory Reset

  1. Remove the Smart Plug from the receptacle.
  2. Press and hold the button on the front for 15 seconds.
  3. Insert the Smart Plug back into the receptacle.
  4. Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Insert the Smart Plug into any wall outlet.
  4. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the Smart Plug from the receptacle.
  3. Press and hold the button on the front for 15 seconds.
  4. Insert the Smart Plug back into the receptacle.
  5. Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Button

3460-L

Button
Zigbee

Factory Reset

  1. Remove battery. Wait 10 seconds then re-insert battery.
  2. Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
    • NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
    • The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
    • NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
    • The LED can be dim, if you're in a well lighted area this light could be difficult to see.
  4. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove battery. Wait 10 seconds then re-insert battery.
  3. Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than blink blue (even more faintly).
    • NOTES: The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
    • The LED can be dim, if you're in a well lighted area this light could be difficult to see.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Door/Window Sensor

3320-L

Contact Sensor
Zigbee

Factory Reset

  1. Slide off the battery cover, remove the battery and wait ten seconds.
  2. Using a paper clip, press and hold the reset button completely down while reinserting the battery.
  3. Hold for an additional two seconds and release. The contact sensor should begin blinking blue.
    • NOTE: The reset button is a small black button above the battery.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Remove battery. Wait 10 seconds then re-insert battery.
  4. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  5. After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Slide off the battery cover, remove the battery and wait ten seconds.
  3. Using a paper clip, press and hold the reset button completely down while reinserting the battery.
  4. Hold for an additional two seconds and release. The contact sensor should begin blinking blue.
    • NOTE: The reset button is a small black button above the battery

Brand
Device
Product Number
Device Type
Protocol
IRIS
Garage Door Opener

GD-00Z-1

Garage Door Opener
Z-Wave Plus

Factory Reset

  1. Unplug your device - wait 10 seconds
  2. Restore power to the device
  3. Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.

Join the Z-Wave Network

  1. Perform a factory reset before attempting to join the Z-Wave network.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Ensure your Iris Garage Door Controller is plugged in, and the tilt sensor battery is active/working.
  4. Press the Link (Z-Wave) button once located on the left of the Iris Garage Door Controller.
  5. When your device triple beeps, it has successfully joined the Z-Wave network.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Once the controller is ready to exclude your device, press the Link (Z-Wave) button once located on the left side of the device.
  4. The garage door controller should give a short beep immediately followed by a long beep.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Keypad

3405-L

Keypad
Zigbee

Factory Reset

  1. Remove the battery and wait ten seconds.
  2. Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
    • Note: The factory reset process puts the security keypad back into pairing mode.
  3. Upon a proper reset the top right icon will be blinking green on your keypad.
  4. You may now insert the 2nd battery.

Join the Zigbee Network

  1. Perform a factory reset before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Remove battery. Wait 10 seconds then re-insert battery.
  4. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
    • Note: The factory reset process puts the security keypad back into pairing mode.
  3. Upon a proper reset the top right icon will be blinking green on your keypad.
  4. You may now insert the 2nd battery.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V3 Keypad

iL02_1

Keypad
Zigbee

Factory Reset

  1. Remove only 1 AA battery and wait ten seconds.
  2. Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
  3. A blinking blue light indicates the device is reset and ready to pair again.

Join the Zigbee Network

  1. Remove only 1 AA battery and wait ten seconds.
  2. Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
  3. A blinking blue light indicates the device is reset and ready to pair again.
  4. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove only 1 AA battery and wait ten seconds.
  3. Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light blinks red once.
  4. A blinking blue light indicates the device is reset and ready to pair again.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Motion Sensor

3326-L

Motion Sensor
Zigbee

Factory Reset

  1. Remove the battery and wait 10 seconds
  2. Press and hold the reset button on the left side of the device as you reinsert the battery.
  3. Hold for an additional two seconds and release.
    • Note: The reset button is a small white button located on the side of the motion sensor.
  4. Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
  5. A blinking blue light indicates the device is reset and ready to pair again.

Join the Zigbee Network

  1. Factory reset the device before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Remove the battery for 10 seconds and re-insert.
  4. Replace the battery cover. The sensor's blue LED will flash while searching for the hub.
  5. Once paired the LED will stop blinking.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press and hold the reset button on the left side of the device as you reinsert the battery.
  3. Hold for an additional two seconds and release.
    • Note: The reset button is a small white button located on the side of the motion sensor.
  4. Upon a successful reset your device will now be blinking blue - indicating it's ready to pair.
  5. A blinking blue light indicates the device is reset and ready to pair again.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V3 Motion Sensor

iL07_1

Motion Sensor
Zigbee

Factory Reset

  1. Remove the battery and wait ten seconds.
  2. Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
  3. A blinking blue light indicates the device is ready to pair.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Remove the battery and wait ten seconds.
  3. Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
  4. A blinking blue light indicates the device is ready to pair.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the battery and wait ten seconds.
  3. Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
  4. A blinking blue light indicates the device is ready to pair.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Smart Plug

3210-L

Outlet
Zigbee

Factory Reset

  1. Remove the Smart Plug from the outlet and wait ten seconds.
  2. Press and hold the small white button on the front of the plug.
  3. While holding the button, insert the Smart Plug back into the outlet.
  4. As soon as the LED on the front of the plug lights up, release the button.
  5. If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.

Join the Zigbee Network

  1. Factory reset the device before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Insert your smart plug into any wall outlet. Your smart plug should be blinking blue, that means it's in pairing mode.
  4. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press and hold the small white button on the front of the plug.
  3. While holding the button, insert the Smart Plug back into the outlet.
  4. As soon as the LED on the front of the plug lights up, release the button.
  5. If the reset was successful the blue LED on the front of the smart plug will be blinking. This means your smart plug is now ready to pair.

Brand
Device
Product Number
Device Type
Protocol
IRIS
V2 Smart Fob

3450-L

Button Controller
Zigbee

Factory Reset

  1. Twist open the battery cover on the back of the Smart Fob.
  2. Remove the battery and wait ten seconds
  3. Reinstall the battery with the positive side facing you.
  4. Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
  5. Confirm that the fob has been reset by checking that the fob's background light is flashing blue. If it does not do this, check the battery and retry from step 2.

Join the Zigbee Network

  1. Factory reset the device before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
  4. The Smart Fob's LED will blink blue while searching for the hub.
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Twist open the battery cover on the back of the Smart Fob.
  3. Remove the battery and wait ten seconds
  4. Reinstall the battery with the positive side facing you.
  5. Once the battery is installed, push any of the four buttons 8 times in a row, once per second.

Brand
Device
Product Number
Device Type
Protocol
IRIS
Smart Water Sensor

3315-L

Water Sensor
Zigbee

Factory Reset

  1. Remove the cover from the sensor, then remove the battery for at least 10 seconds.
  2. Press and hold the reset button while reinserting the battery.
  3. Hold for an additional two seconds and release.
  4. A successful reset will be indicated by a blinking blue light on your sensor

Join the Zigbee Network

  1. Factory reset the device before attempting to pair.
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Remove the battery and wait ten seconds.
  4. Re-insert the battery
  5. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  6. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the cover from the sensor, then remove the battery for at least 10 seconds.
  3. Press and hold the reset button while reinserting the battery.
  4. Hold for an additional two seconds and release.
  5. A successful reset will be indicated by a blinking blue light on your sensor

KEEN Home

Brand
Device
Product Number
Device Type
Protocol
KEEN Home
Smart Vent
Vent
Zigbee

Factory Reset

  1. Press the black button on the back inside of the Smart Vent battery compartment five times.
  2. You will know that the Smart Vent has been properly reset when the LED starts double blinking green

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Removed the battery cartridge and reinsert it to bring the vent online.
  3. Press the black button on the back inside of the Smart Vent battery compartment five times.
  4. This should force the vent into join-mode once again.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press the black button on the back inside of the Smart Vent battery compartment five times.
  3. You will know that the Smart Vent has been properly reset when the LED starts double blinking green

Kwikset

Brand
Device
Product Number
Device Type
Protocol
Kwikset
SmartCode
910 / 912 / 914
Lock
Z-Wave

Factory Reset

  1. Remove battery pack
  2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
  3. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
  4. Perform the door handing process again.
    • Press and hold the Lock button while installing battery pack.
    • Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
    • If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.

Join the Z-Wave Network

  1. Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press button A on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
  4. If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  5. Press button A on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press button A on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.

Brand
Device
Product Number
Device Type
Protocol
Kwikset
SmartCode
910 / 912 / 914
Lock
Zigbee

Factory Reset

  1. Remove battery pack
  2. Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
  3. Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
  4. Perform the door handing process again.
    • Press and hold the Lock button while installing battery pack.
    • Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
    • If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.

Join the Zigbee Network

  1. Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Press button A on the lock 4 times to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
    • If pairing is unsuccessful, press button B on the lock 9 times and repeat the pairing process.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Press button B on the lock 9 times.

Leak Intelligence

Brand
Device
Product Number
Device Type
Protocol
Leak Intelligence
Leak Gopher
Valve
Z-Wave

Factory Reset

  1. Unplug your device - wait 10 seconds
  2. Restore power to the device
  3. Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-Wave button once.
  3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  4. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Once the controller is ready to exclude your device, press the Z-Wave button once.

Leviton

Brand
Device
Product Number
Device Type
Protocol
Leviton
4-Scene Controller
VRCS4
Button Controller
Z-Wave

Factory Reset

  1. On the 4-Scene controller, press and hold buttons 1 and 3.
  2. Wait approximately 5 seconds until the LED turns amber and then solid red.
  3. Release the buttons and the 4-Scene controller will be reset. NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.

Join the Z-Wave Network

Leaving the Z-Wave Network


Linear

Brand
Device
Product Number
Device Type
Protocol
Linear (GoControl)
Door / Window Sensor
WADWAZ-1
Contact Sensor
Z-Wave

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
  3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  4. The LED on the sensor will stop blinking
  5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Tamper switch of WADWAZ-1 for 1 second and release to exclude the device form the Z-wave network.
  4. The LED light will flash continuously when the sensor is in the excluded condition.

Brand
Device
Product Number
Device Type
Protocol
Linear (GoControl)
PIR Motion Detector
WAPIRZ-1
Motion Sensor
Z-Wave

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Depress the Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
  3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  4. The LED on the sensor will stop blinking
  5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Tamper switch of WAPIRZ-1 for 1 second and release to exclude the device form the Z-wave network.
  4. The LED light will flash continuously when the sensor is in the excluded condition.

Brand
Device
Product Number
Device Type
Protocol
Linear (GoControl)
Siren / Strobe
WA105DBZ-1
Siren
Z-Wave

Factory Reset

  1. Factory reset is achieved by performing a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin blinking.
  3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  4. The LED on the sensor will stop blinking
  5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
  4. The LED light will flash continuously when the sensor is in the excluded condition.

Lutron

Brand
Device
Product Number
Device Type
Protocol
Lutron
Lutron Dimmers and Switches
Dimmer / Switch
Lutron Clear Connect

Factory Reset

  1. Tap the "On" button quickly three times, holding on the last press.
  2. Continue to hold the "On" button until the light begins to flash quickly.
  3. Release the button, then immediately tap the button three more times.
  4. All paired Pico remote controls are removed and all settings are returned to factory default.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
Caséta Smart Bridge Pro
L-BDGPRO2
Bridge
Lutron Clear Connect

Network Reset

  1. First, press and hold the black button on the back of your Smart Bridge for 20 seconds.

Factory Reset

  1. Quickly triple tap and hold the Add button. DO NOT release after the third tap.
  2. Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
  3. Release the button and quickly perform another triple tap of the button. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
  4. The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.

NOTE: Lutron does not recommend factory resetting a Smart Bridge Pro unless advised by a member of the Lutron technical support team.


Brand
Device
Product Number
Device Type
Protocol
Lutron
Pico Remote
PJ2-
Button Controller
Lutron Clear Connect

Factory Reset

  1. Tap the "On" button quickly three times, holding on the last press.
  2. Continue to hold the "On" button until the light begins to flash quickly.
  3. Release the button, then immediately tap the button three more times.
  4. All paired Pico remote controls are removed and all settings are returned to factory default.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
Radio RA2 Keypads
Keypad
Lutron Clear Connect

Factory Reset

  1. Tap the "On" button quickly three times, holding on the last press.
  2. Continue to hold the "On" button until the light begins to flash quickly.
  3. Release the button, then immediately tap the button three more times.
  4. The RA2 keypad has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
Radio RA2 Main Repeater
RR-MAIN-REP
Repeater
Lutron Clear Connect

Factory Reset

  1. Triple tap and hold the Test button on a Main Repeater. DO NOT release the button after the third tap.
  2. Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately 3 seconds).
  3. Release the Test button and immediately triple tap it again. All the LEDs will flash red quickly.
  4. When the LEDs stop flashing, the Main Repeater has been returned to factory settings

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
Radio RA2 Occupancy Sensors
Motion Sensor
Lutron Clear Connect

Factory Reset

  • Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)
  1. Quickly triple tap and hold the Test, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
  2. Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
  3. Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
  4. The Sensor has now been returned to Factory Default Settings.
  • Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)
  1. Quickly triple tap and hold the Test or Light button on the Sensor. DO NOT release after third tap.
  2. Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
  3. Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
  4. The Sensor has now been returned to Factory Default Settings.
  • Radio Powr SavrTM Occupancy/Vacancy Wall-Mounted Sensor
  1. Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
  2. Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
  3. Release the button and triple tap the button again until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
  4. The Sensor has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
Radio RA2 Select Main Repeater
RR-SEL-REP2
Repeater
Lutron Clear Connect

Factory Reset

  1. Quickly triple tap and hold down any button on the Main Repeater. DO NOT release after the third tap.
  2. Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash red slowly (approximately once per second).
  3. Release the button and quickly perform another triple tap of the button. The Main Repeater LEDs will flash green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
  4. The Main Repeater and system components have now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device.
Brand
Device
Product Number
Device Type
Protocol
Lutron
RadioRA2 VCRX Visor Control Receiver
RR-VCRX
Garage Controller
Lutron Clear Connect

Factory Reset

  1. Quickly triple tap and hold any button (except Learn) on the VCRX. DO NOT release after third tap.
  2. Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
  3. Release the button and triple tap the button again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
  4. The VCRX has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device.
Brand
Device
Product Number
Device Type
Protocol
Lutron
Serena Shades
Shade Control
Lutron Clear Connect

Factory Reset

  1. Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
  2. Immediately tap the shade button quickly three more times, until the shade button LED blinks green rapidly, then blinks red/green three times, and turns off.
  3. The Serena shade has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device
Brand
Device
Product Number
Device Type
Protocol
Lutron
Sivoia QS Triathlon Shades
Shade Control
Lutron Clear Connect

Factory Reset

  1. Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED blinks green rapidly.
  2. Immediately tap the shade button quickly three more times, until the shade button LED blinks Green rapidly, then blinks Red/Green three times, and turns off.
  3. The Sivoia shade has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

Brand
Device
Product Number
Device Type
Protocol
Lutron
RadioRA2 Fan Control

RRD-2ANF

Fan Controller
Lutron Clear Connect

Factory Reset

  1. Triple tap the tapswitch on a control. DO NOT release after the third tap.
  2. Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
  3. Release the tapswitch and immediately triple tap the tapswitch again.
  4. The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device.
Brand
Device
Product Number
Device Type
Protocol
Lutron
Lutron Caséta Fan Control

PD-FSQN

Fan Controller
Lutron Clear Connect

Factory Reset

  1. Tap the "On" button quickly three times, holding on the last press.
  2. Continue to hold the "On" button until the light begins to flash quickly.
  3. Release the button, then immediately tap the button three more times.
  4. All paired Pico remote controls are removed and all settings are returned to factory default.

Join the Lutron Clear Connect network

  1. See the Lutron Integrator documentation.

Leaving the Lutron Clear Connect network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform a factory reset on the device

LUX

Brand
Device
Product Number
Device Type
Protocol
Lux
KONOz
Thermostat
Zigbee

Factory Reset

  1. Access the installation settings by going to the main menu and selecting the gear icon.
  2. You will see “IS” on the screen and will be prompted to select “yes” or “no”.
  3. Select “yes” to access the installation settings.
  4. Rotate the knob to view settings and press the knob to confirm.
  5. Once in the installer settings, rotate the knob to 99.
  6. Press the knob to confirm, then press and hold the knob for 3 seconds.

Join the Zigbee Network

  1. Perform factory reset.
  2. KONOz is now ready to be configured for your heating and cooling system. The KONOz will guide you through the initial system configuration.
  3. After confirming your system settings, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET” to establish a connection.
  4. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Perform factory reset.

MCO Home

Brand
Device
Product Number
Device Type
Protocol
MCO Home
Dimmer Switch
MH-DT311
Dimmer
Z-Wave

Factory Reset

  1. Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power.
  2. The factory setting will be restored.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press 3 times on "+" or "-" button to add the device. If successful, the green LED blinks 4 times.
    • Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED blinks 4 times.
    • Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.

Monoprice

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Door/Window Sensor

24259
Contact Sensor
Z-Wave Plus

Factory Reset

  1. To reset the sensor, press and hold the Z-button for about 20 seconds.
  2. The LED will change from steadily illuminated to blinking then back to steadily illuminated, indicating that the reset operation was successful.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Rapidly press the Z-button 3 times to include the device in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Rapidly press the Z-button 3 times to exclude the device from the network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Plug-In Dimmer

11994
Dimmer
Z-Wave

Factory Reset

  1. Ensure that the smart plug is inserted into an AC outlet.
  2. Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Plug-In ON/OFF

11995
Outlet
Z-Wave

Factory Reset

  1. Ensure that the smart plug is inserted into an AC outlet.
  2. Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Recessed Door/Window sensor

15268
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for 2 seconds then disappear.
  3. If linking was unsuccessful, the LED will continue to blink if you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-button on your Sensor. If your switch has been successfully unlinked to your network, its LED will start to blink for a short time.
  4. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will blink when tapped.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Door/Window Sensor

15270
Contact Sensor
Z-Wave

Factory Reset

  1. Ensure that the smart plug is inserted into an AC outlet.
  2. Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

PIR Motion Sensor with Temperature

15271
Motion Sensor
Z-Wave

Factory Reset

  1. Ensure that the smart plug is inserted into an AC outlet.
  2. Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Plug-in Outlet

15654
Outlet
Z-Wave Plus

Factory Reset

  1. Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. If the plug-in has not already been included into a Z-Wave network, the LED indicator will blink rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can jooin the Hubitat Elevation™ Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Triple-click the Z-Button. The plug-in will be removed from your Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

4 in 1 motion sensor

15902
Motion Sensor
Z-Wave Plus

Factory Reset

  1. Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network and has returned it to a factory state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Momentarily press the Program Switch
  3. The LED should blink 5 times indicating the sensor has not yet been included in the Z-Wave network.
  4. If the LED blinks only 1 time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
  5. Momentarily press the button again after it blinks 5 times, to automatically include the sensor in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Monoprice

Smart Plug and Repeater

27481
Outlet
Z-Wave Plus

Factory Reset

  1. Ensure that the smart plug is inserted into an AC outlet.
  2. Press and hold the Z-Button on the smart plug for more than 20 seconds.
  3. The LED indicator will illuminate yellow steadily for about 2 seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Rapidly press the Z-button 3 times to include the device in the network.

Testing the Smart Plug Z-Wave connection

You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.

To begin testing, press and hold the Z button for 6-9 seconds, releasing the button when the RGB LED illuminates violet.

  • Note: The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
    • Blinking Green: The RGB LED will blink green while the smart plug is attempting to establish a connection with the main controller.
    • Solid Green: The RGB LED will illuminate green for about 2 seconds to indicate that direct communications are stable.
    • Blinking Orange: The RGB LED will blink orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
    • Solid Orange: The RGB LED will illuminate orange for about 2 seconds to indicate that the communication quality is moderate.
    • Solid Red: The RGB LED will illuminate red for about 2 seconds to indicate that they communications attempt has failed.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Rapidly press the Z-button 3 times to exclude the device from the network.
  4. The RGB LED will blink orange while the smart plug is being removed.
  5. The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate orange steadily for about 2 seconds.

Neo

Brand
Device
Product Number
Device Type
Protocol
Neo

Door/Window Sensor

NAS-DS01ZE
Contact Sensor
Z-Wave

Factory Reset

  1. Remove the cover of contact sensor main body.
  2. Make sure the sensor is connected to power source.
  3. Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
  4. Release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the code button, the LED light will flash for 5 times.
  3. The contact sensor will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Neo

Door/Window Sensor

NAS-DS02ZU
Contact Sensor
Z-Wave

Factory Reset

  1. Remove the cover of contact sensor main body.
  2. Make sure the sensor is connected to power source.
  3. Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
  4. Release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the code button, the LED light will flash for 5 times.
  3. The contact sensor will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Neo

Motion Sensor

NAS-PD01ZU-T
Motion Sensor
Z-Wave

Factory Reset

  1. Remove the sensor’s cover.
  2. Make sure the sensor is connected to power source.
  3. Press the code button for 10 seconds, the LED will flash red for 1 time.
  4. Release the code button.
    • NOTE: When the PIR is being restored to factory settings, please make sure a power source is connected.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the code button, the LED light will flash for 5 times.
  3. The motion sensor will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the code button, the LED light will flash for 5 times and the sensor will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Neo

Power Plug

NAS-WR02Z
Outlet
Z-Wave

Factory Reset

  1. Press and hold the code button on the front of the outlet for 10 seconds.
  2. When the LED flashes, release the button.
  3. When the outlet has been reset, the LED will flash on and off 5 times within a 2 second period.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the code button, the LED light will flash for 5 times.
  3. The device will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the code button, the LED light will flash for 5 times and the device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Neo

One Key SOS

NAS-RC03ZU
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the code button for 10 seconds.
  2. Release the Code button. Note: Do not power off during factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the red SOS alarm button.
  3. The device will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the red SOS alarm button and the device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Neo

One Key SOS and Remote Control

NAS-RC03ZU
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the code button for 10 seconds.
  2. Release the Code button. Note: Do not power off during factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Quickly, triple-click the red SOS alarm button.
  3. The device will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Quickly, triple-click the red SOS alarm button and the device will be excluded from the Z-Wave network.

NodOn

Brand
Device
Product Number
Device Type
Protocol
NodOn

Octan Remote

CRC-3US-1
Button Controller
Z-Wave Plus

Factory Reset

  1. A simultaneous long press (1sec) on O and will perform this factory reset.
  2. The LED will blink red and green to validate the reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Simultaneously push on the solid circle and the + for 1sec.
  3. The LED glows in pink to confirm the selection
  4. Push on the solid circle within 10 seconds.
  5. The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure.
  6. The device will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Simultaneously push on the solid circle and the + for 1sec.
  4. The LED glows in pink to confirm the selection
  5. Push on the solid circle within 10 seconds.
  6. The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure
  7. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
NodOn

Soft Remote

CRC-3US-6
Button Controller
Z-Wave Plus

Factory Reset

  1. A simultaneous long press (1sec) on O and will perform this factory reset.
  2. The LED will blink red and green to validate the reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Simultaneously push on the solid circle and the + for 1sec.
  3. The LED glows in pink to confirm the selection
  4. Push on the solid circle within 10 seconds.
  5. The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure.
  6. The device will be detected and included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Simultaneously push on the solid circle and the + for 1sec.
  4. The LED glows in pink to confirm the selection
  5. Push on the solid circle within 10 seconds.
  6. The LED blinks in pink to confirm your choice and then blinks in green to confirm the procedure
  7. The device will be excluded from the Z-Wave network.

NYCE

Brand
Device
Product Number
Device Type
Protocol
NYCE

Curtain Motion Sensor

NCZ-3045-HA
Motion Sensor
Zigbee

Factory Reset

  1. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  2. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  3. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  4. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  3. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Press the button 4 times to join the device to the Zigbee network.
  5. The LED will flash in the following sequences:
    • Yellow - Red - Yellow flashes indicate it is searching for a network to join.
    • Yellow - Green - Yellow flashes indicate the device is being configured.
    • 3 Green flashes indicate the device has sucessfully joined the network.
    • 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  3. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  5. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Brand
Device
Product Number
Device Type
Protocol
NYCE

Ceiling Motion Sensor

NCZ-3043-HA
Motion Sensor
Zigbee

Factory Reset

  1. Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
  2. Inside the battery compartment is a small button on the side of the circuit board.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  3. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  4. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
  3. Inside the battery compartment is a small button on the side of the circuit board.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Press the button 4 times to join the device to the Zigbee network.
  5. The LED will flash in the following sequences:
    • Yellow - Red - Yellow flashes indicate it is searching for a network to join.
    • Yellow - Green - Yellow flashes indicate the device is being configured.
    • 3 Green flashes indicate the device has sucessfully joined the network.
    • 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
  3. Inside the battery compartment is a small button on the side of the circuit board.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  5. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Brand
Device
Product Number
Device Type
Protocol
NYCE

Motion Sensor

NCZ-3041-HA
Motion Sensor
Zigbee

Factory Reset

  1. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  2. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  3. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  4. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  3. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Press the button 4 times to join the device to the Zigbee network.
  5. The LED will flash in the following sequences:
    • Yellow - Red - Yellow flashes indicate it is searching for a network to join.
    • Yellow - Green - Yellow flashes indicate the device is being configured.
    • 3 Green flashes indicate the device has sucessfully joined the network.
    • 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
  3. Inside the battery compartment at the top, is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  5. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Brand
Device
Product Number
Device Type
Protocol
NYCE

Garage Door (Tilt) Sensor

NCZ-3014-HA
Contact Sensor
Zigbee

Factory Reset

  1. Slide open the Garage Door (Tilt) Sensor’s top housing.
  2. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  3. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  4. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide open the Garage Door (Tilt) Sensor’s top housing.
  3. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Press the button 4 times to join the device to the Zigbee network.
  5. The LED will flash in the following sequences:
    • Yellow - Red - Yellow flashes indicate it is searching for a network to join.
    • Yellow - Green - Yellow flashes indicate the device is being configured.
    • 3 Green flashes indicate the device has sucessfully joined the network.
    • 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Slide open the Garage Door (Tilt) Sensor’s top housing.
  3. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  5. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Brand
Device
Product Number
Device Type
Protocol
NYCE

Door/Window Sensor

NCZ-3011-HA
Contact Sensor
Zigbee

Factory Reset

  1. Slide open the Door/Window Sensor’s top housing.
  2. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  3. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  4. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide open the Door/Window Sensor’s top housing.
  3. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Press the button 4 times to join the device to the Zigbee network.
  5. The LED will flash in the following sequences:
    • Yellow - Red - Yellow flashes indicate it is searching for a network to join.
    • Yellow - Green - Yellow flashes indicate the device is being configured.
    • 3 Green flashes indicate the device has sucessfully joined the network.
    • 3 Red flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from step 4.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Slide open the Door/Window Sensor’s top housing.
  3. Inside the battery compartment is a small button.
    • Note: The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.
  4. Pressing the button 10 times will leave the network and reset the device to factory defaults.
  5. The LED will flash Red 3 times to indicate is has left the network (If joined), and it will flash Green 5 times to indicate defaults have been restored.

Orbit

Brand
Device
Product Number
Device Type
Protocol
Orbit

Smart Hose Faucet Timer

27087
Irrigation Controller
Zigbee

Factory Reset

  1. Insert two AA alkaline batteries and re-insert the tray.
  2. Press the RESET button 5 times in rapid secession.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide out the battery tray on the back of the timer.
  3. Insert two AA alkaline batteries and re-insert the tray.
    • NOTE: Firmly replace the battery tray to ensure water resistance and increase battery life. You will know the battery tray is fully inserted if it does not pull out easily.
  4. Turn the dial to AUTO.
  5. When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
    • NOTE: The timer will remain in pairing mode for 10 minutes or until paired. If pairing is not successful after 10 minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button 5 times in rapid secession.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press the RESET button 5 times in rapid secession.

Brand
Device
Product Number
Device Type
Protocol
Orbit

12-Station Sprinkler Controller

27396
Irrigation Controller
Zigbee

Factory Reset

  1. Ensure the controller is connected to power.
  2. Press the SYNC button 5 times in rapid secession.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Ensure the controller is connected to power.
  3. Turn the dial to AUTO.
  4. When the controller is first connected to power, it will automatically attempt to connect.
    • NOTE: If pairing is not successful after 10 minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button 5 times in rapid succession
  5. The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words SMART MODE will appear on the screen.
  6. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
  7. Watch the status in the device details page to confirm proper operation

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove
  2. Press the SYNC button 5 times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for 5 seconds to cancel re-pairing.

Orvibo

Brand
Device
Product Number
Device Type
Protocol
Obvibo
Motion Sensor
SN11
Motion Sensor
Zigbee

Factory Reset

  1. Hold down the reset button on the front of the motion sensor until the Green light goes out.
  2. This will disconnect the sensor from the Zigbee network.
  3. Short-press the reset button and the Green light will flash slowly.
  4. The sensor is now in pairing mode.

Join the Zigbee Network

  1. Remove the cover by rotating it counterclockwise
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Hold down the reset button on the front of the motion sensor until the Green light goes out.
  4. This will disconnect the sensor from the Zigbee network.
  5. Short-press the reset button and the Green light will flash slowly.
  6. The sensor is now in pairing mode.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Hold down the reset button on the front of the motion sensor until the Green light goes out.
  3. This will disconnect the sensor from the Zigbee network.

Radio Thermostat Company of America

Brand
Device
Product Number
Device Type
Protocol
Radio Thermostat Company of America
Thermostat
CT-101
Thermostat
Z-Wave

Factory Reset

  1. The thermostat must be in OFF mode.
  2. Wait until the radio wave icons on the left side of the screen stop blinking then touch the screen once to turn on the back light and then hold the center of the screen for about 8 seconds until the thermostat beeps.

Factory Reset (Alternate Method)

  1. Place the CT101 in the off position by pressing mode button until OFF is shown at the top left of the screen.
  2. Press the menu button
  3. Press and hold the center of the screen for about 5 sec or until the screen changes then release.
  4. You will see two arrows. First press the up arrow and wait for the count down.
  5. Now press the down arrow and again, wait for the count down.
  6. All parameter values will be restored to defaults and a message is sent to any radio module installed to instruct the module to restore its own default values.
    • The thermostat will now resets itself.
  7. Press the house to get back to the main screen.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press/Touch the MATE button on the MENU screen. A large r1 will be displayed.
  3. This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will blink.
  4. When a device has joined a network the LINK icon will appear under the radio tower.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press/Touch the MATE button on the MENU screen. A large r1 will be displayed.
  4. This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will blink.
  5. When a device has excluded from the network, the LINK icon will disappear under the radio tower.

Schlage

Brand
Device
Product Number
Device Type
Protocol
Schlage
Connect Deadbolt
BE-469
Lock
Z-Wave

Factory Reset

  1. Disconnect the batteries
  2. Press and hold the outside Schlage button
  3. While holding the outside Schlage button, then reconnect the batteries.
  4. Release the Outside Schlage Button. NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.
  5. To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
  6. If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  2. Press the Schlage button
  3. Enter the 6 digit programming code
  4. Press 0
  5. A indicates the lock successfully joined the Z-Wave network, while an X indicates that it did not successfully join the network

Verify Z-Wave connection status from the lock

  1. Remove the battery cover
  2. Disconnect the battery connector
  3. While watching the inside Schlage button, reconnect the battery connector
  4. The inside Schlage button will blink if the lock is enrolled

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Schlage button
  4. Enter the 6 digit programming code
  5. Press 0
  6. A indicates the lock was successfully excluded the Z-Wave network, while an X indicates that it did not successfully leave the network

Utilitech

Brand
Device
Product Number
Device Type
Protocol
Utilitech
Indoor Siren
TSE07
Siren
Z-Wave

Factory Reset

  1. Remove the battery cover
  2. Press the pairing button in between the batteries 8 times, one second apart

Join the Z-Wave Network

  1. Remove the battery cover
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
  3. Press the paring button once

Exclusion from the Z-Wave Network

  1. Remove the battery cover
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the paring button once

*Note: Aeotec was formerly known as Aeon Labs.