Difference between revisions of "Join and Reset Instructions"

From Hubitat Documentation
Jump to: navigation, search
(Added Sengled Light Strip and Outlet)
(Replaced content with " <big>'''We're moving!''' Please visit http://docs2.hubitat.com for the latest documentation.</big> <big> This information is now available in the new compatible device l...")
(Tag: Replaced)
 
(64 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See [[How to Build a Solid Z-Wave Mesh]] for further detail on methods of Exclusion.
 
  
=='''<big>ADT</big>'''==
+
<big>'''We're moving!''' Please visit http://docs2.hubitat.com for the latest documentation.</big>
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>ADT (Nortek)</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Leak Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>10016864C</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
  
#Remove the cover by rotating it counterclockwise
+
<big>
#Press and hold the Connect button for '''5''' seconds
+
This information is now available in the new compatible device list (hover over the "Instructions" column) in: http://docs2.hubitat.com/devices/list-of-compatible-devices
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode.
+
</big>
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Remove the cover by rotating it counterclockwise
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the Connect button for '''5''' seconds
 
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
=='''<big>AduroSmart</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>AduroSmart</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>ERIA 81822</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Use the provided pin to press and hold the reset button for 10 seconds.
 
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Use the provided pin to press and hold the reset button for '''10''' seconds.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>AduroSmart</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>ERIA 81825</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
 
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold down the off (circle) button for '''10''' seconds until it flashes green '''3''' times.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>AduroSmart</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>ERIA 81823</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Use the provided pin to press and hold the reset button for '''10''' seconds.
 
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Use the provided pin to press and hold the reset button for '''10''' seconds.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
=='''<big>Aeotec (Aeon Labs)</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW056</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and then release it.
 
#Your Doorbell will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing as a confirmation.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
 
#If your Doorbell has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop. If linking was unsuccessful, the LED will flash when you tap its button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Doorbell.
 
#If your Doorbell has been successfully unlinked to your network, its LED will begin to flash slowly indicating it is ready to be paired to a new network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW162-A</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action button for '''20''' seconds
 
#Within '''2-5''' seconds, the test doobell sound will run, then stop after '''5''' seconds has elapsed.
 
#From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
 
#After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 
#With the LED pulsing, release the Action button, and the Doorbell 6 will be reset to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Power Doorbell 6 through the provided power adapter.
 
#Ensure that Doorbell 6 LED is flashing slowly.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the Doorbell 6 Action Button once.
 
#If Doorbell 6 has successfully paired to your Z-Wave gateway, the LED will be a solid color for '''30''' seconds, then turn off.
 
#If is fails to join the Z-Wave network, the LED will flash slowly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button '''6''' times in '''2''' seconds.
 
#If your Doorbell 6 has been successfully unpaired from the Z-Wave network, its LED will begin to flash slowly, indicating it is ready to join a Z-Wave network again.
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW112</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold Door Window Sensor 6 Action button
 
#Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
 
#If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the button on the Door Window Sensor 6
 
#The LED will flash green to indicate successful inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#If your Door Window Sensor is successfully removed from the Z-Wave network, the RGB LED will become a colorful gradient for a few seconds and then turn off. If the removing was unsuccessful, the RGB LED will be solid for 8 seconds and then turn off, repeat the above steps.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW120</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once to include the door/window sensor.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast flash for '''8''' seconds and then slow flash for '''3''' seconds when you press the Action Button again.
 
#If the removal was unsuccessful, the Status LED will fast flash for '''2''' seconds and then be solid for '''2''' seconds when you press the Action Button, repeat the above steps.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor Gen2</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSB29</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once to include the door/window sensor.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor to exclude it from the network
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor 1E</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSB04100</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Use an Aeon Z-Stick or Minimote to return the sensor to a default state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
 
#The sensor will now stay awake for '''10''' minutes to receive network instructions. The LED on the will be flashing while awake.
 
#*Note: The DSB04100 sensor can only be taught to communicate to devices within its own network.
 
#*If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for '''5''' seconds.
 
#*If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Use an Aeon Z-Stick or Minimote to exclude the sensor from previous networks
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Controller Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW062</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and release.
 
#Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing to confirm a success.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful exclusion.
 
#The Network LED on the Garage Door Controller should now be flashing slowly to indicate it is ready to be paired to a new network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dry Contact Sensor Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW097</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds, then disappear.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
 
#If unlinking was not successful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Aeon Labs Home Energy Meter</big>'''</div>
 
|<div style="text-align: center;">'''<big>AEDSB09104ZWUS</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''10''' seconds.
 
#If successful, the LED on the HEM should begin to flash slowly.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Remove the screw from the back of your Reader and open the battery cover.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for '''1''' second. If the linking was unsuccessful the light will flash after pressing your meter’s Action Button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the screw from the back of your Reader and open the battery cover.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully removed from your network, its light will flash for '''1''' second.
 
#If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
 
 
 
----
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Home Energy Meter Gen2 / Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW095</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''10''' seconds.
 
#If successful, the LED on the HEM should begin to flash slowly.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to flash.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will flash. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.
 
 
 
----
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>LED Bulb Gen5</big>''' </div>
 
|<div style="text-align: center;">'''<big>ZW098</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Removing LED Bulb from your Z-Wave network will reset LED Bulb to default factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#With LED Bulb in its fitting, wait '''2''' seconds. Now toggle your wall switch ON. LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
 
#After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Turn LED Bulb’s wall switch on.
 
#Toggle LED Bulb’s wall switch off, on, off, on, off, on within '''2''' seconds. The LED should flash orange, and if successful, the orange LED will be solid for '''2''' seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
 
#To confirm successful removal its color will change to orange for '''2''' seconds before changing to white. If removal was unsuccessful, LED Bulb will flash orange for '''3''' seconds before changing to red for '''2''' seconds.
 
 
 
----
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>LED Bulb 6 Multi-Color</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA002</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn LED Bulb’s wall switch on and wait '''1''' second.
 
#Toggle LED Bulb's wall switch '''6''' times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
 
#If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white '''3''' times to indicate a successful factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to '''10''' seconds.
 
#After successfully connecting to your network, LED Bulb will flash green -> white color for '''3''' seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for '''3''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle LED Bulb’s wall switch '''3''' times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
 
#LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for '''3''' seconds.
 
 
 
----
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>LED Bulb 6 Multi-White</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn LED Bulb’s wall switch on and wait '''1''' second.
 
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
 
#If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will flash '''2''' times to indicate that it is looking for a Z-Wave network to connect to.
 
#After successfully connecting to your network, LED Bulb will flash off then on in about '''0.5''' second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Turn LED Bulb’s wall switch on and wait '''1''' second.
 
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
 
#LED Bulb 6 if successful will flash once, dim to 5% for '''5''' seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
 
 
 
----
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Micro Illuminator G2</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSC19103-ZWUS</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Hold the Z-Wave button for '''30''' seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for '''30''' seconds).
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Connect Micro Smart Dimmer to an AC‐input power source.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z‐Wave button.
 
#If the inclusion fails, please repeat the process from step 2.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z‐Wave button.
 
#If the exclusion fails, please repeat the process from step 2
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Micro Motor Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSC14104-ZWEU/US, DSC14103-ZWAU</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motor Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Use an Aeon Z-Stick or Minimote to return the controller to a default state.
 
 
 
'''Join the Z-Wave Network''' '''(Z-Stick)'''
 
 
 
#Connect Micro Motor Controller to an AC‐input power source.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Micro Motor Controller.
 
#If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
 
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
 
 
 
'''Join the Z-Wave Network''' '''(Minimote)'''
 
 
 
#Connect Micro Motor Controller to an AC‐input power source.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#Press the Include button on your Minimote.
 
#Press the Action Button on your Micro Motor Controller.
 
#If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
 
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press any button on your Minimote to take it out of inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network''' '''(Z-Stick)'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#Press the Action Button on your Micro Motor Controller.
 
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
 
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
 
 
 
'''Exclusion from the Z-Wave Network''' '''(Minimote)'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Remove Button on your Minimote.
 
#Press the Action Button on your Micro Motor Controller.
 
#If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
 
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press any button on your Minimote to take it out of removal mode.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Micro Switch G2</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSC26 / DCS18</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the button on the Micro Switch G2 for '''20''' seconds and then release it.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch '''6''' times (ON to OFF or OFF to ON).
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Minimote</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSA03202</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Pull down the panel on the  Minimote
 
#Press and hold the bottom '''2''' buttons down. The Red and Blue LED will alternate faster and faster.
 
#When both Red and Blue LED become solid, you may let go.
 
 
 
'''Include a device''' '''from the Z-Wave Network'''
 
 
 
#Tap the Inclusion (+) button, LED should be flashing blue
 
#Tap the button on the device you want to add
 
#After the LED stops flashing rapidly, tap any button to get out of inclusion mode
 
 
 
'''Exclusion a device from the Z-Wave Network'''
 
 
 
#Tap the Exclusion (-) button, LED should flash red
 
#Tap button on the device you want to remove
 
#After LED stops flashing rapidly, tap any button to get out of the exclusion mode
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multisensor Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW074</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold Multisensor Gen5 Action button (For '''20''' seconds)
 
#The LED of the Multisensor Gen5 will flash faster and faster. At '''20''' seconds, the LED should become solid for '''1-2''' seconds to confirm factory reset.
 
#Release the Multisensor Gen5 Action Button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on your MultiSensor.
 
#You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
 
#If the LED flashes when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on your MultiSensor.
 
#If your MultiSensor has been successfully removed from your network, its LED will flash when you press the Z-wave Button.
 
#If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multisensor 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW100</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
 
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash Green rapidly, followed by a solid Green LED for '''1''' second for a successful inclusion, or a solid red LED for '''1''' second for a failed inclusion.
 
#You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
 
#If the green LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
 
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>NanoMote One</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA004</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
 
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Double click the NanoMote button, the LED will flash rapidly with a white color.
 
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
 
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
 
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Double click the NanoMote button, the LED will become a solid green color.
 
#If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>NanoMote Quad</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA003</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
 
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Double click the NanoMote button (can be any button), the LED will flash rapidly with a white color.
 
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
 
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
 
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Double click the NanoMote button, the LED will become a solid green color.
 
#If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.
 
 
 
<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Nano Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW111</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and then release it.
 
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into pairing mode.
 
#If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
 
#If the pairing was unsuccessful, the red LED will be on for '''2''' seconds and then remain a colorful gradient, repeat the steps above.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Nano Switch (with energy reading)</big>''' </div>
 
|<div style="text-align: center;">'''<big>ZW116</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and then release it.
 
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Nano Switch (without energy reading)</big>''' </div>
 
|<div style="text-align: center;">'''<big>ZW139</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and then release it.
 
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Range Extender (Aeon Labs Z-Wave Network Repeater)</big>'''</div>
 
|<div style="text-align: center;">'''<big>DSD37</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Use an Aeon Z-Stick or Minimote to return the Range Extender to a default state.
 
 
 
'''Join the Z-Wave Network''' '''(Z-Stick)'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
 
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press the Action Button on the Z-Stick to take it out of installation mode.
 
 
 
'''Join the Z-Wave Network''' '''(Minimote)'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions
 
#Press the Include button on your Minimote.
 
#If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
 
#If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
 
#Press any button on your Minimote to take it out of inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network''' '''(Z-Stick)'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Z-Stick.
 
#If your Range Extender has been successfully removed from your network, its Network LED will flash.
 
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press the Action Button on the Z-Stick to take it out of removal mode.
 
 
 
'''Exclusion from the Z-Wave Network''' '''(Minimote)'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Remove Button on your Minimote.
 
#If your Range Extender has been successfully removed from your network, its Network LED will flash.
 
#If the removal was unsuccessful, the Network LED will not flash.
 
#Press any button on your Minimote to take it out of removal mode.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Range Extender 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW117</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Z-Wave Button for '''20''' seconds to completely factory reset your Range Extender 6.
 
#During the time that you are holding your Range Extender 6 action button down, the LED will flash through these colors: Yellow (at '''2''' seconds) > Purple (at '''5''' seconds) > Red for '''8''' seconds (initializing factory reset) > Green for '''20''' seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
 
#You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will flash green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
 
#If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for '''2''' seconds then turn off. If the adding was unsuccessful, the red LED will be on for '''2''' seconds and then remain colorful gradient status, repeat the steps above.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on your Range  Extender.
 
#If Range Extender has been successfully removed  from your network, its RGB LED will remain colorful gradient status.
 
#If the removal was unsuccessful, the RGB LED will still be solid, repeat the steps above.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Recessed Door Sensor Gen5</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW089</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds then disappear.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
 
#If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW080</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action button for '''20''' seconds
 
#At 8 seconds, the Siren will sound for '''1''' second, then stop
 
#The LED will continue to flash faster and faster and then will then turn solid for '''2''' seconds to indicate a successful factory reset
 
#You may let go of its Action button, and the Siren Gen5 factory reset is complete.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Siren Gen5, and its LED will flash rapidly to indicate that it is communicating.
 
#If your Siren has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop.
 
#If linking was unsuccessful, the LED will flash when you tap its button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Siren.
 
#If your Siren has been successfully unlinked from your network, its LED will begin to flash.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW164-A</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action button for '''20''' seconds
 
#Within '''2-5''' seconds, the test siren sound will run, then stop after '''5''' seconds has elapsed.
 
#From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
 
#After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 
#With the LED pulsing, release the Action button, and the Siren 6 will be reset to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Power Siren 6 through the provided power adapter.
 
#Ensure that Siren 6 LED is flashing slowly.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly tap the Siren 6 Action Button once.
 
#If Siren 6 has successfully joined your Z-Wave network, the LED will emit a solid color for '''30''' seconds, then turn off.
 
#If the Siren 6 failed to pair, the LED will continue to blink slowly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button '''6''' times within '''2''' seconds .
 
#If your Siren 6 has been successfully excluded from the Z-Wave network, its LED will begin to flash slowly which indicates that it is ready to be paired again.
 
 
 
<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Switch 6</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW096 / ZW110</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''20''' seconds.
 
#The LED will change between these colors: Yellow > Purple > Red (flashs faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
 
#When the LED changes to Green state, you may let go of the action button.
 
#When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Switch once and the LED will flash a green LED.
 
#If your switch has been successfully linked to your network, its LED will become solid green for '''2''' seconds.
 
#If linking was unsuccessful, the LED will return to a rainbow gradient.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Switch.
 
#If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
 
#If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.
 
 
 
<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>TriSensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA005</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action Button for '''15''' seconds.
 
#The red LED flashes to confirm a successful factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your sensor once.
 
#The LED will turn yellow LED for '''10''' seconds.
 
#If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your sensor.
 
#The LED will turn purple for '''2''' seconds, and then white when exclusion is successful.
 
 
 
<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>WallMote Quad</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW129</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action button for '''20''' seconds.
 
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 
|<div style="text-align: center;">'''<big>WallMote Quad</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW130</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the Action button for '''20''' seconds.
 
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
 
 
 
<hr />
 
 
 
=='''<big>Alfred</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Alfred</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>DB2 / DB2-B</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the door and keep the lock bolt in the unlock position.
 
#Open the battery box to access the reset button.
 
#Using a pointed object, press and hold the reset button.
 
#Keep the reset button held down while removing and replacing one of the batteries.
 
#Keep holding the reset button down until you hear the voice guidance.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Touch the lock screen with your hand to activate it.
 
#Press * twice, followed by your master PIN code and #
 
#Digits 1-8 on the keypad should lightup in response.
 
#Enter '''8''', followed by '''1''' to put the lock into inclusion mode.
 
#*'''NOTE:'''  It is recommended that you delete all user codes from the lock if any are previously existing and use Hubitat Elevation™ Lock Code Manager to program the lock.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#You must have your lock first connected to the August App
 
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Touch the lock screen with your hand to activate it.
 
#Press * twice, followed by your master PIN code and #
 
#Digits 1-8 on the keypad should lightup in response.
 
#Enter '''8''', followed by '''2''' to put the lock into exclusion mode.
 
 
 
<hr />
 
 
 
=='''<big>August</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>August</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Lock Pro</big>'''</div>
 
|<div style="text-align: center;">'''<big>ASL-03</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#You must have your lock first connected to the August App
 
#Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
 
#*My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
 
#*My Hub is No Longer Working - use this mode to RESET the Device.
 
#Select the '''My Hub is No Longer Working''' option and then select '''Reset Z-Wave Device'''.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#You must have your lock first connected to the August App
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#On the August App, go into Lock Settings and door for Z-Wave Settings.
 
#The first time the screen will state that "The Lock is not connected to a Z-Wave Network". Select "Add to a Z-Wave Network".
 
#Follow the instructions to put the lock into Learn Mode.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#You must have your lock first connected to the August App
 
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device.
 
#Select Remove Z-Wave Device and on the next page you will see two options.
 
#*My Hub is in Exclusion Mode - Use this mode when you have a working hub and can properly disconnect.
 
#*My Hub is No Longer Working - Use this mode to RESET the Device.
 
#Select the My Hub is in Exclusion Mode option to exclude the lock from the Z-Wave network.
 
 
 
<hr />
 
 
 
=='''<big>BeSense</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>BeSense</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zwave PLUS Ceiling PIR Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>IX32</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the tamper switch for '''6''' times to restore factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
 
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>BeSense</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zwave Plus Window/Door Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM20</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the tamper switch for '''6''' times to restore factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
 
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>BeSense</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zwave PIR Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>IX30</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press the tamper switch for '''6''' times to restore factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
 
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface, go to the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
 
 
 
<hr />
 
 
 
=='''<big>BOSCH</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>BOSCH</big>'''</div>
 
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>ISW-ZPR1-WP13</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unlock the battery cover and slide it upwards to remove.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 
#Wait at least '''4''' seconds, but do not release the tamper switch.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Release the tamper switch. The device is now reset to factory default settings.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Unlock the battery cover and slide it upwards to remove.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#Remove both batteries for at least '''10''' seconds.
 
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
 
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
 
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>BOSCH</big>'''</div>
 
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>ISW-ZDL1-WP11G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unlock the battery cover and slide it upwards to remove.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 
#Wait at least '''4''' seconds, but do not release the tamper switch.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Release the tamper switch. The device is now reset to factory default settings.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Unlock the battery cover and slide it upwards to remove.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#Remove both batteries for at least '''10''' seconds.
 
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
 
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
 
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 
 
 
=='''<big>Centralite</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Pearl Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>3000-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
 
#The device will then factory reset itself and begin looking for an open network to join.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
 
#The device will then factory reset itself and begin looking for an open network to join.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>3-Series Smart Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>3200-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unplug any devices from the module and unplug from the wall.
 
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Unplug any devices from the module and unplug from the wall.
 
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>3-Series Door & Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3300-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>3-Series Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3305-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>3-Series Micro Door Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3323-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>3-Series Micro Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3328-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Centralite</big>'''</div>
 
|<div style="text-align: center;">'''<big>4-Series Smart Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>4200-C</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unplug any devices from the module and unplug from the wall.
 
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Unplug any devices from the module and unplug from the wall.
 
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
#After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Unplug any devices from the module and unplug from the wall.
 
#Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
 
 
 
<hr />
 
 
 
=='''<big>CREE</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>CREE</big>'''</div>
 
|<div style="text-align: center;">'''<big>Connected LED Bulbs</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
 
#The bulb will flash once, indicating it is reset and ready for pairing
 
 
 
'''Factory Reset (Alternate Method)'''
 
 
 
*'''''Method 1 - Use a Philips Hue Dimmer Switch'''''
 
 
 
#Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
 
#Hold the remote within '''4''' inches of the bulb.
 
#Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about '''10''' seconds, until the bulb starts flashing on and off.
 
#If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 
 
 
*'''''Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)'''''
 
 
 
#Hold the remote within '''4''' inches of the bulb.
 
#Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
 
#The bulb should flash on and off
 
#The green LED on the remote should come on and may flash a few times.
 
#Continue to hold both buttons on the remote until the green LED goes off completely.
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
 
#The bulb will flash once, indicating it is reset and ready for pairing
 
 
 
'''Join the Zigbee Network''' '''(Alternate Method)'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#See '''Factory Reset (Alternate Method)''' above to reset the bulb and put it into pairing mode.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
=='''<big>Dome</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMWD1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the Cover and make sure the Door/Window Sensor is powered.
 
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Cover of the Door/Window Sensor.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the Cover of the Door/Window Sensor.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMDP1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
 
#Wait for '''5''' seconds.
 
#Move the Magnet and Sensor Base in and out of the closed position '''6''' times.
 
#The LED indicator will light up Red for '''5''' seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Sensor Cover and the LED indicator will start flashing yellow.
 
#Press the Button quickly '''3''' times in a row.
 
#The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green '''3''' times then flash red until the cover is replaced.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the SENSOR COVER and the LED indicator will start flashing red.
 
#Press the Button quickly '''3''' times in a row.
 
#The LED Indicator will flash green '''3''' times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMWS1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the Back Plate and make sure the Leak Sensor is powered.
 
#Hold the Connect Button for '''10''' seconds until the LED indicator flashs once, then release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Leak Sensor by twisting it apart.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the cover of the Leak Sensor by twisting it apart.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMMS1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the Cover and make sure the Motion Detector is powered.
 
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Motion Detector by twisting it apart.
 
#Press the Connect Button quickly '''3''' times in a row.
 
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Mouser</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMMZ1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Mouse Trap</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Press and hold the CONNECT BUTTON for at least '''10''' seconds then release.
 
#A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Press the CONNECT BUTTON quickly '''3''' times in a row.
 
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Press the CONNECT BUTTON quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>On/Off Plug-In Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMOF1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Plug in the On/Off Plug-In Switch.
 
#Hold the Connect Button for '''10''' seconds until the LED Indicator flashes once, then release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
 
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Range Extender</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMEX1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Hold the Button for '''10''' seconds until the LED flashes '''10''' times, then release the button
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#For proper inclusion, install the Range Extender in the final location where it will be used.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash '''5''' times indicating successful inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Button quickly '''3''' times in a row The LED will flash '''5''' times indicating successful exclusion.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMS01</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the Back Plate and make sure the Siren is powered.
 
#Hold the Connect Button for '''10''' seconds until the LED Ring flashs once, then release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Back Plate of the Siren.
 
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the Back Plate of the Siren.
 
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dome</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Main Shut-Off</big>'''</div>
 
|<div style="text-align: center;">'''<big>DMWV1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Shutoff Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the open/close button for at least '''10''' seconds then release.
 
#The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly '''3''' times in a row. The LED will stop flashing and stay on continuously upon successful inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#When prompted, press the “open/close” button on the Shut-Off quickly '''3''' times in a row.
 
 
 
<hr />
 
 
 
=='''<big>Dragon Tech</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Dragon Tech</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug in Z-Wave Plus Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>PD-100</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unplug the PD-100 and anything the is plugged into it.
 
#Press and hold the button on the front of the PD-100
 
#Plug the PD-100 in while still pressing the button
 
#After '''3''' seconds, release the button. If the button flashes, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button on the front of the PD-100
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the button on the front of the PD-100
 
 
 
<hr />
 
 
 
==<big>'''Eaton''' '''(Cooper Wiring Devices)'''</big>==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Eaton</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wireless Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>RF9540</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Cooper Wiring Devices Z-Wave device has a blue LED, which will flash when the device is not included in a Z-Wave network. The LED stops flashing when the device is in a network.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the device switch once to include it in the network. The LED will stop flashing, indicating the dimmer has been successfully included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>Ecolink</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>DWZWAVE2.5-ECO</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flood/Freeze Sensor</big>''' </div>
 
|<div style="text-align: center;">'''<big>FLF-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#The Flood Freeze sensor factory defaults on network exclusion
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for '''1''' second, then reinstall it.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for at least '''10''' seconds, then reinstall it.
 
#If the LED starts flashing continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for '''10''' seconds if adding to a Z-Wave network fails.
 
#If after '''5''' seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Open the Flood Freeze case and remove the battery for '''1''' second.
 
#Replace the battery and the device should be removed from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor with Pet Immunity</big>''' </div>
 
|<div style="text-align: center;">'''<big>PIR-ZWAVE2.5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>SC-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 
#The LED on the front of the unit will turn off if successful exclusion from the network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 
#The LED on the front of the unit will turn off if successful included in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
 
#The LED on the front of the unit will turn off if successful exclusion from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>FireFighter</big>'''</div>
 
|<div style="text-align: center;">'''<big>FF-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke/CO Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If the LED starts flashing continually, the sensor has not been added. Repeat the steps.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>DLS-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#The LED on the front of the unit will turn off if successfully included in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Switch Double Toggle</big>''' </div>
 
|<div style="text-align: center;">'''<big>DTLS2-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#The LED on the front of the unit will turn off if successful included in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Switch Dual Rocker</big>'''</div>
 
|<div style="text-align: center;">'''<big>DDLS2-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#The LED on the front of the unit will turn off if successful included in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
 
|<div style="text-align: center;">'''<big>TILT-ZWAVE2</big>'''</div>
 
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Tilt Sensor</big>''' </div>
 
|<div style="text-align: center;">'''<big>TILT-ZWAVE2.5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Tilt Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Ecolink</big>'''</div>
 
|<div style="text-align: center;">'''<big>Toggle Light Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>TLS-ZWAVE5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#The LED on the front of the unit will turn off if successful included in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
 
 
<hr />
 
 
 
=='''<big>Enerwave</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Enerwave</big>'''</div>
 
|<div style="text-align: center;">'''<big>Ceiling Mounted PIR Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWN-BPC-Plus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor '''3''' times and hold for '''3''' seconds on the 3rd press.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion/exclusion button on the sensor '''3''' times.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the inclusion/exclusion button on the sensor '''3''' times.
 
 
 
<hr />
 
=='''<big>Eva Logik</big>'''==
 
{| class="wikitable sortable"
 
|-
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Eva Logik</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW36</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the button for '''5''' seconds when powered on
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See Discovering your devices for detail instructions.
 
#Press the button on the switch 3 times within '''2''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Top button on the switch 3 times within '''2''' seconds.<hr />
 
 
 
{| class="wikitable sortable"
 
|-
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Eva Logik</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW37</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the button for 10 seconds when powered on
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See Discovering your devices for detail instructions.
 
#Press the button on the switch 3 times within '''2''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Top button on the switch 3 times within '''2''' seconds.<hr />
 
 
 
=='''<big>Everspring</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>HSM02</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
 
#Within '''1''' second, press and hold the tamper switch until LED is off.
 
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flood Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>ST812</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press link key three times within '''1.5''' second. The sensor will beep each time the link key is pressed.
 
#Within '''1''' second, press and hold the link key. The sensor will long beep for '''5''' seconds. Keep holding the link key until the long beep stops.
 
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pressing link key three times within '''1.5''' second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Pressing link key three times within '''1.5''' second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>PIR Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>HSP02</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
 
#Within '''1''' second, press and hold the tamper switch until LED is off.
 
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Photoelectric Smoke Alarm</big>'''</div>
 
|<div style="text-align: center;">'''<big>SF-813</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press tamper switch three times within '''1.5''' second. The LED flashes and the buzzer sounds when the link key is pressed.
 
#Within '''1''' second, press and hold the tamper switch for '''5''' seconds until the LED is off.
 
#The LED will light for '''5''' seconds and the buzzer will sound for '''5''' seconds
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
 
#The detector will stay awake and remain in inclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
 
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has joined the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
 
#The detector will stay awake and remain in exclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
 
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has been excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Everspring</big>'''</div>
 
|<div style="text-align: center;">'''<big>Temperature/Humidity Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>SF-814</big>'''</div>
 
|<div style="text-align: center;">'''<big>Temperature Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
 
#Within '''1''' second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
 
 
 
<hr />
 
=='''<big>Evolve</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Evolve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Isolated Contact Fixture Module</big>'''</div>
 
|<div style="text-align: center;">'''<big>LFM-20</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is unavailable for this device. Instead, perform a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
 
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button on the device once to include it in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
 
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
 
 
 
<hr />
 
 
 
=='''<big>Fibaro</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGPB-101</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Click the Button exactly five times.
 
#Press and hold the Button for at least '''5''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Click the button at least '''6''' times.
 
#Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
 
#Click the button '''4''' times to wake it up
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click the Button at least '''6''' times.
 
#Wait for the removing process to end.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor 2</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGDW-002</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the cover and remove the battery.
 
#Install the battery while holding both TMP buttons.
 
#The LED indicator will be flashing slowly for '''5''' seconds, but keep holding the buttons.
 
#Release one button when the LED indicator starts flashing quickly.
 
#Click the released button once to confirm initiation of the reset procedure.
 
#Wait a few seconds for a long flash of the LED indicator. '''Do not remove the battery'''.
 
#The LED indicator will flash '''5''' times quickly to confirm reset of the device.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flood Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGFS-101 FG3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Make sure the sensor is powered.
 
#Press and hold the TMP button.
 
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
 
#Release the TMP button.
 
#Click the TMP button once to confirm selection.
 
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Removed the battery for '''10''' seconds, and re-install it
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the TMP button quickly, '''3''' times in a row.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flood Sensor ZW5</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGFS-101 ZW5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Make sure the sensor is powered.
 
#Press and hold the TMP button.
 
#Wait for the visual LED indicator to glow yellow (4th position of the MENU).
 
#Release the TMP button.
 
#Click the TMP button once to confirm selection.
 
#After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the TMP button quickly, '''3''' times in a row.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the TMP button quickly, '''3''' times in a row.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>KeyFob</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGKF-601 ZW5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Click '''O''' and '''<big>–</big>''' simultaneously.
 
#Click '''∆''' or '''X''' until LED is '''Yellow''' - reset the device.
 
#Click '''<big>+</big>''' to confirm selection, or is you do not wish to reset at this time, click <big>'''–'''</big> to exit the menu.
 
#The LED will pulse '''Yellow''' twice to confirm the device has been reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#LED will pulse '''White''' during the adding process.
 
#Wait for the inclusion process to end.
 
#Successful adding will be confirmed by the Z-Wave controller’s message.
 
#Successful inclusion will be confirmed by Hubitat Elevation™ and the remote LED will be '''Green'''.
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click '''O''' and '''<big>–</big>''' simultaneously.
 
#Click '''∆''' or '''X''' until LED is '''Green.'''
 
#Click '''<big>+</big>''' to confirm selection.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor ZW5</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGMS-001 ZW5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Open the cover
 
#Press and hold the B-button.
 
#Wait for visual indicator to glow '''Yellow''' (2nd menu position).
 
#Release the '''B''' button and then briefly click the B-button to confirm selection
 
#After few seconds the device will be reset, which is signaled with the '''Red''', fading visual indicator color.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the '''B''' button quickly, three times in a row.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the '''B''' button quickly, three times in a row.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGRGBW-101</big>'''</div>
 
|<div style="text-align: center;">'''<big>RGBW Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Disconnect the supply voltage.
 
#Press and hold the '''B''' button located inside the RGBW Controllers casing.
 
#Connect the the supply voltage, while still holding the '''B''' button.
 
#Release the '''B''' button.
 
#The '''B''' channel will turn on (blue channel).
 
#Disconnect  the power supply.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
('''Auto Inclusion''')
 
 
 
#Make sure the RGBW Controller is not connected to a supply.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect voltage supply to auto-include the RGBW Controller.
 
#The RGBW Controller will be automatically recognized and included in the Z-Wave network.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''(Manual Inclusion''')
 
 
 
#Make sure the RGBW Controller is not connected to a supply.
 
#To disable auto-inclusion press the '''B''' button briefly, after re-connecting the RGBW Controller to its supply voltage.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
 
#The RGBW Controller will be recognized and included in the Z-Wave network.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Triple click the '''B''' button or any switch connected to I1-I4 inputs.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Single Switch 2</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGS-213</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Switch off the mains voltage (disable the breaker).
 
#Remove the Switch 2 from the wall switch box.
 
#Switch on the mains voltage.
 
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
 
#Quickly release and click the '''B''' button again.
 
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Identify the S1 switch.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly, three times press the '''S1 switch'''.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly, three times press the '''S1 switch'''.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Radiator Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>FIBEFGT-001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the button at the base of the thermostat head.
 
#Release when the LED ring is '''Yellow'''.
 
#Briefly press the button to confirm selection.
 
#The device will reset and then go into Standby Mode.
 
#Briefly press the button to activate the thermostat again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly '''3''' times in a row, press the at the base of the thermostat head.
 
#The LED ring will start blinking '''White'''.
 
#Successful inclusion will be confirmed by Hubitat Elevation™ and the LED ring will show '''Green'''.
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Quickly '''3''' times in a row, press the at the base of the thermostat head.
 
#The LED ring will start blinking '''White'''.
 
#Successful exclusion will be confirmed by Hubitat Elevation™ and the LED ring will show '''Red'''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGWPB-111 / FGWPB-121</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Make sure the device is powered.
 
#Press and hold the button.
 
#Wait for the LED frame to glow yellow (3rd menu position).
 
#Release the button and then briefly click the button once to confirm the selection.
 
#After few seconds the device will restart with factory settings, which is signaled with the red frame color.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug the device into a socket.
 
#The LED frame will glow red signaling it has not being added (If is doesn't you must first perform a general exclusion and then a factory reset).
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly, triple click the button located on the casing.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Plug the device into a socket.
 
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#The LED frame will glow green signaling it is currently included in a Z-Wave network (If it doesn't, then the exclusion process is not needed at this time).
 
#Quickly, triple click the button located on the casing.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wall Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGWPE-102</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the button located on the side.
 
#The device will cycle through GREEN, then VIOLET, and finally YELLOW for device reset.
 
#Release the button.
 
#Press the button again to confirm the selection and factory reset the device.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug the device into a socket nearby the main Z-Wave controller.
 
#The LED frame will glow red signaling not being added (reset or remove the device otherwise).
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly, triple click the button on the side of the device.
 
#The device will be included to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly, triple click the button on the side of the device.
 
#Plug the device into a socket nearby the main Z-Wave controller.
 
#The LED frame will glow green signaling being added (removing is not necessary otherwise).
 
#Quickly, triple click the button on the side of the device.
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Fibaro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer 2</big>'''</div>
 
|<div style="text-align: center;">'''<big>FGS-212</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Switch off the mains voltage (disable the breaker).
 
#Remove the Dimmer 2 from the wall switch box.
 
#Switch on the mains voltage.
 
#Press and hold the '''B''' button to enter the menu until the visual LED indicator is '''Yellow'''.
 
#Quickly release and click the '''B''' button again.
 
#After few seconds the device will be restarted, which is signaled by the '''Red''' LED indicator color.
 
#The device enters the calibration mode.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Identify switch no. 1 (turns the light on) or the B-button (located on the device’s housing).
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly press switch no. 1 or the '''B''' button three times.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Identify the '''S1 switch''' on the Fibaro Single Switch 2 From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press switch no. 1 or the '''B''' button three times.
 
#The device will be excluded from the Z-Wave network.
 
#Dimmer 2 will start the calibration process
 
 
 
<hr />
 
=='''<big>First Alert</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>First Alert</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke & Carbon Monoxide Combo Alarm</big>''' </div>
 
|<div style="text-align: center;">'''<big>ZCOMBO-G</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke / CO Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Power up the device with the test button held down for '''10''' or more seconds
 
#The device will reset all Z-Wave settings and leave the network. '''NOTE: The device will not remain awake after resetting and will go into standby mode.'''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Slide battery door open and insert batteries.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will remain awake for 30 seconds on inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide battery door open, then remove and re-insert batteries.
 
#Press and hold the test button. Keep it held down as you slide the battery drawer closed. You may then release the button and the alarm will be excluded from the network.
 
 
 
<hr />
 
=='''<big>FortrezZ</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>FortrezZ</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multiple In / Out module</big>''' </div>
 
|<div style="text-align: center;">'''<big>MIMO2+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the program button for '''15''' seconds and then release.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Briefly press the program button once.
 
#The status LED will flash when inclusion to the Z-Wave network completes.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Briefly press the program button once.
 
#The status LED will flash when the device has been excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>FortrezZ</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multiple In / Out module</big>''' </div>
 
|<div style="text-align: center;">'''<big>MIMOLite</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the program button for '''15''' seconds and then release.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#When the LED has a periodic single flash, the unit will be automatically included to the Z-Wave network.
 
#If the LED is not flashing, then the  button has been previously pressed and automatic inclusion mode is no longer active. In this case, briefly press the program button once.
 
#The status LED will flash when the device has been excluded from the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Briefly press the program button once.
 
#The status LED will flash when the device has been excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>GE/Jasco</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE</big>'''</div>
 
|<div style="text-align: center;">'''<big>Link Bulb</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn OFF the light for '''3''' second.
 
#Turn ON the light for '''3''' seconds
 
#Repeat this process '''5''' times
 
#The bulb will dim and then flash once when successfully reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Turn the bulb on.
 
#The bulb will flash when connected to the hub.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>12718</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-in Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>12719/ZW4101</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outdoor Plug-in Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>12720/ZW4201</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;"> '''<big>In-Wall Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>12721</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;"> '''<big>In-Wall Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>12722</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;"> '''<big>In-Wall Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>12724</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Toggle Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>12727</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press up and release the toggle switch to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press up and release the toggle switch to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press up and release the toggle switch to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Toggle Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>12729</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press up and release the toggle switch to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press up and release the toggle switch to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press up and release the toggle switch to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
 
|<div style="text-align: center;">'''<big>12730/ZW4002</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
 
#*12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-In Outdoor Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>14284</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Unplug the switch from the outlet
 
#Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Fan Control</big>'''</div>
 
|<div style="text-align: center;">'''<big>14287</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
 
#The LED will flash ON/OFF '''5''' times when completed successfully.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless fan control rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
 
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Tamper Resistant Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>14288</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the manual/program button '''3''' times, then press and hold the button for at least '''3''' seconds. The LED will flash '''5''' times to confirm.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>14291</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
 
#The LED will flash ON/OFF '''5''' times when completed successfully.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless smart switch rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
 
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>14294</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
 
#The LED will flash ON/OFF '''5''' times when completed successfully.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to add it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
 
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>26931</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and release the top button '''10''' times within '''5''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom button on the smart switch to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom button on the smart switch to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Motion Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>26933</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and release the top button '''10''' times within '''5''' seconds. The LED will flash '''3''' times quickly confirming change
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the top or bottom button on the smart switch to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top button on the smart switch to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>28167</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#If plugged in, unplug the Dimmer from the receptacle.
 
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-in Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>28169</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#If plugged in, unplug the Dimmer from the receptacle.
 
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the manual/program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the manual/program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>Hinge Pin Smart Door Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>32563/ZW6301</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and release the program button '''10''' times quickly.
 
#The LED light will flash approximately eight times.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Single press and release the program button on the device to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Single press and release the program button on the device to exclude it from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>45856</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the top of the rocker (ON Switch) with '''10''' quick short presses.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Remove power from the dimmer at the circuit breaker.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Restore power to the Smart Dimmer at the circuit breaker
 
#Pairing Begins Automatically: LED Status Indicator flashs as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
 
#*'''Note:''' ''LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GE/Jasco</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>45857</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Lift the air-gap switch at the bottom of the rocker to OFF position to power down the device.
 
#Hold down the UP button
 
#Push In the air-gap switch to ON position to power up the device.
 
#Release the UP button within '''4''' seconds of power up.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Remove power from the dimmer at the circuit breaker.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Restore power to the Smart Dimmer at the circuit breaker
 
#Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
 
#*'''Note:''' ''LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
=='''<big>GoControl</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GoControl</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Controllers</big>'''</div>
 
|<div style="text-align: center;">'''<big>GD00Z</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}''Includes Linear GD00Z-2, GoControl GD00Z-4, Linear GD00Z-5, ADT GD00Z-6, GoControl GD00Z-7 and NuTone ND00Z''
 
 
 
'''Factory Reset'''
 
 
 
#Reset the controller by pressing the Link button '''5''' times.
 
#A quick beep followed by a longer beep will indicate proper reset for the GD00Z series or ND00Z.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and release the Link button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the Link button.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>GoControl</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>WADWAZ-1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program switch of WADWAZ-1 for '''1''' second and release. The LED light will flash continuously when the sensor has been successfully excluded.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Unscrew the screw fastening the rear cover and slide the rear cover down
 
#Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the sensor has not yet performed inclusion with the controller.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Once Hubitat Elevation™ discovers the device, the LED will stop flashing. If the LED does not stop flashing and is not discovered by your hub, relocate the WADWAZ-1 to within 100 feet (line of sight) of a Z-Wave repeater or your hub and restart Z-Wave Inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program switch of WADWAZ-1 for '''1''' second and release. The LED light will flash continuously when the sensor has been successfully excluded.
 
 
 
<hr />
 
=='''<big>Graber</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Graber</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motorized Shades</big>'''</div>
 
|
 
|<div style="text-align: center;">'''<big>Shade</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
 
 
'''Network Reset'''
 
 
 
#Press and hold the button on the headrail end cap for '''7''' seconds or until the shade jogs once.
 
#Release the button.
 
#*NOTE: The will not reset the shade limits
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash '''Green.'''
 
#Release the button.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash '''Green.'''
 
#Release the button
 
#The shade will be excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>Halo Labs</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Halo</big>'''</div>
 
|<div style="text-align: center;">'''<big>Halo+</big>'''</div>
 
|<div style="text-align: center;">'''<big>LS001A</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke/CO Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#To reset, hold down center button for approximately '''20''' or more seconds.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Once Halo greets you, it will automatically begin searching for a ZigBee network. Halo will glow for a couple minutes before timing out.
 
#*To awaken the detector, double-tap the center button or hold the button for approximately '''3''' or more seconds.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Hold down the center button for approximately '''20''' ot more seconds. Halo will reset all ZigBee settings and leave the network. .
 
 
 
<hr />
 
=='''<big>Hampton Bay</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Hampton Bay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wink Enabled Ceiling Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>MR101Z</big>'''</div>
 
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Turn off your fan for '''3''' seconds, then turn it on for '''3''' seconds (Repeat '''5''' times)
 
#The light will flash three times when the factory reset is successful.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Turn on your fan.
 
#When successful, the fan will turn on at low speed and the light will flash three times.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Perform a factory reset on the fan controller
 
 
 
<hr />
 
=='''<big>Hank</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Hank</big>'''</div>
 
|<div style="text-align: center;">'''<big>One-Key Scene Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>HKZW-SCN01</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and holding the center "Z-button" for 20 seconds.
 
#Release the button after '''20''' seconds and the LED will stay yellow for '''3''' seconds.
 
#Within the '''3''' second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the battery.
 
#Triple click the center "Z-button".
 
#If inclusion is successful, the LED will flash '''blue''' for less than '''5''' seconds, and then it will remain solid for '''15''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#If exclusion is successful, the LED will flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Hank</big>'''</div>
 
|<div style="text-align: center;">'''<big>Four-Key Scene Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>HKZW-SCN04</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and holding the center "Z-button" for '''20''' seconds.
 
#Release the button after '''20''' seconds and the LED will stay yellow for '''3''' seconds.
 
#Within the '''3''' second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the battery.
 
#Triple click the center "Z-button".
 
#If inclusion is successful, the LED will flash '''blue''' for less than '''5''' seconds, and then it will remain solid for '''15''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#If exclusion is successful, the LED will flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Hank</big>'''</div>
 
|<div style="text-align: center;">'''<big>RGBW LED Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>HKZW-RGB01</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle power to the bulb off and on '''3''' times quickly.
 
#Within '''3''' times toggling the bulb, the final ending state of the switch or plug must be on.
 
#If the exclusion is successful, the RGB BULB will quicly flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Make sure power to the bulb is disconnected and the RGB BULB is close to the hub.
 
#Insert the bulb into a socket and then turn it on.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle power to the bulb off and on '''3''' times quickly.
 
#Within '''3''' times toggling the bulb, the final ending state of the switch or plug must be on.
 
#If the exclusion is successful, the RGB BULB will quickly flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
 
 
 
<hr />
 
=='''<big>HomePro</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>HomePro</big>'''</div>
 
|<div style="text-align: center;">'''<big>Exterior Appliance Module</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZRP110</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the button on the front of the module once.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the button on the front of the module once.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the button on the front of the module once.
 
 
 
<hr />
 
=='''<big>Homeseer</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Indicator Light Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-FS100-L+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Light Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the Z-Wave button inside the sensor body for '''10''' seconds
 
#If successful, the LED will flash '''5''' times.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Perimeter Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-FS100-W+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the Z-Wave button inside the sensor body for '''10''' seconds
 
#If successful, the LED will flash '''5''' times.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave network button on the front of the unit one time and wait for the inclusion process to finish. This may take some time.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave network button on the front of the unit one time and wait for the exclusion process to finish. This may take some time.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wall Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-WD200+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Turn dimmer on by tapping the top of the paddle once.
 
#Quickly tap top of the paddle '''3''' times.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Wall Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-WS200+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Turn dimmer on by tapping the top of the paddle once.
 
#Quickly tap top of the paddle '''3''' times.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the paddle of the dimmer to begin the inclusion process. This will take a few moments to complete.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the paddle of the dimmer to begin the exclusion process. This will take a few moments to complete.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-DS100+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Z-Wave button inside the sensor body for '''20''' seconds, the LED will stay on until the button is released.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
 
#If successful, the sensor body LED will flash briefly and then stay on for '''3''' seconds.
 
#If unsuccessful, the LED with flash briefly and then turn off. Should this happen, repeat the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Triple-click the Z-Wave button inside the sensor body.
 
#If successful, the LED will turn off within '''1''' second.
 
#If unsuccessful, the LED with flash for '''5''' seconds. Should this happen, repeat the exclusion process.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Homeseer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Leak Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>HS-LS100+</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Z-Wave button for '''20''' seconds. Release the button once the LED stops flashing and glows solidly
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Click the Z-Wave button inside the sensor body once and wait for the process to finish.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Triple-click the Z-Wave button inside the sensor body. Wait for the inclusion process to finish.
 
 
 
<hr />
 
=='''<big>IKEA</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IKEA SYMFONISK</big>'''</div>
 
|<div style="text-align: center;">'''<big>Sound Remote</big>'''</div>
 
|<div style="text-align: center;">'''<big>20370482</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the battery cover from the bottom of the remote and hold the button for 10 seconds to factory reset.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the remote.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery cover from the bottom of the remote and hold the button for 10 seconds.
 
#Save the device and '''without deleting it from the hub''', repeat steps '''1''' and '''2''' above.
 
#The hub will report that it found the previously paired device.
 
#*NOTE: If you do not pair a second time with the device already in the Hubitat Elevation™ database, the remote may not work proplerly.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the battery cover from the bottom of the remote and hold the button for 10 seconds to factory reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IKEA TRÅDFRI</big>'''</div>
 
|<div style="text-align: center;">'''<big>Warm White Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>1000 lm Warm White</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Cycle power '''6''' times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the bulb.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Cycle power '''6''' times. The bulb will begin to dim and finally flash '''1''' time to indicate that it has successfully joined the Zigbee network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Cycle power '''6''' times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the bulb again.
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IKEA TRÅDFRI</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Press and hold the paperclip in the hole for '''2-4''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IKEA TRÅDFRI</big>'''</div>
 
|<div style="text-align: center;">'''<big>Signal Repeater</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#An LED will pulse quickly and then pulse slowly when you release the internal button.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Press and hold the paperclip in the hole for '''2-4''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
 
#The signal repeater will pair as '''Device'''. No driver will be assigned and it is not necessary to have one since this device only repeats Zigbee radio signals.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device again.
 
 
 
<hr />
 
=='''<big>Inovelli</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">'''<big>Brand</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device</big>'''</div>
 
|<div style="text-align: center;">'''<big>Product Number</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device Type</big>'''</div>
 
|<div style="text-align: center;">'''<big>Protocol</big>'''</div>
 
|-
 
|<div style="text-align: center;">'''<big>Inovelli</big>'''</div>
 
|<div style="text-align: center;">'''<big>In-Wall Switch</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Hold the UP button for '''5''' seconds when powered on
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Top button on the switch '''6''' times within '''2''' seconds.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Top button on the switch '''6''' times within '''2''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">'''<big>Brand</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device</big>'''</div>
 
|<div style="text-align: center;">'''<big>Product Number</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device Type</big>'''</div>
 
|<div style="text-align: center;">'''<big>Protocol</big>'''</div>
 
|-
 
|<div style="text-align: center;">'''<big>Inovelli</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the top button for at least '''3''' seconds while you plug the outlet into a recepticle
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Once the controller is ready to include your device, press in and release the button on the switch '''3-5''' times within '''3''' seconds to include it in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Once the controller is ready to exclude your device, press in and release the button on the switch '''3-5''' times within '''3''' seconds to include it in the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Inovelli</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch Module</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Factory reset is accomplished by performing a general exclusion on the device.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the center button '''5''' times within '''1''' second to exclude it in the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the center button '''5''' times within '''1''' second to include it in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the center button '''5''' times within '''1''' second to exclude it in the Z-Wave network.
 
 
 
<hr />
 
=='''<big>IRIS</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Button</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>BTN900</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Button</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within '''10''' seconds of reinserting the battery press the reset button next to the battery '''8''' times in a row, once per second.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#*'''NOTE:''' ''The green light can be dim, if you're in a well lighted area this light could be difficult to see.''
 
#If your button does not flash green check your battery, then retry from step 2.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#With the smart button, squeeze the two sides together by the ridges and gently pull them apart to reveal the battery compartment.
 
#Remove and re-insert the battery. When the smart button begins looking for your hub, the light around the button will flash green.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within 10 seconds of reinserting the battery press the reset button next to the battery '''8''' times in a row, once per second.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see.''
 
#If your button does not flash green check your battery, then retry from step 2.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Care Pendant</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>PDT900</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the pendant should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the supplied access tool into the small opening at the top of the pendant. Gently pry open the case to reveal the battery compartment.
 
#Insert the battery in the correct orientation. The pendant will light up and start flashing as it begins searching for your hub
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the pendant should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Door/Window Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>DWS800</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait '''10''' seconds.
 
#Reinsert the battery and immediately press the white reset button '''8''' times.
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#On the large piece, remove the back by squeezing the semi-circles on either side.
 
#The sensor's LED will flash while searching for the hub.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait '''10''' seconds.
 
#Reinsert the battery and immediately press the white reset button '''8''' times.
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Keyfob</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>KEY903</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Presence Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the key fob should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Insert the battery in the correct orientation. The fob will light up and start flashing as it begins searching for your hub.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the key fob should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>MOT800</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#As soon as the battery is reinserted, press the reset button '''8''' times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#On the large piece, remove the back by squeezing the raised edges on both sides.
 
#Insert the battery. The sensor's LED will flash while searching for the hub.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
 
#As soon as the battery is reinserted, press the reset button '''8''' times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V1 Smart Plug</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>SPG800</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the Smart Plug from the receptacle.
 
#Press and hold the button on the front for '''15''' seconds.
 
#Insert the Smart Plug back into the receptacle.
 
#Immediately press the button on the front of the Smart Plug '''8''' times, allowing 1 second between each press.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the Smart Plug into any wall outlet.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the Smart Plug from the receptacle.
 
#Press and hold the button on the front for '''15''' seconds.
 
#Insert the Smart Plug back into the receptacle.
 
#Immediately press the button on the front of the Smart Plug '''8''' times, allowing 1 second between each press.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Button</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3460-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Button</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Within '''10''' seconds after re-inserting battery, press the button '''8''' times. The light will very dimly flash solid blue, than flash blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Within '''10''' seconds after re-inserting battery, press the button '''8''' times. The light will very dimly flash solid blue, than flash blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Door/Window Sensor</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3320-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Slide the battery cover off, remove the battery and wait '''10''' seconds.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#Hold the reset button for an additional '''2''' seconds and release. The contact sensor should begin flashing blue.
 
#*'''NOTE:''' ''The reset button is a small black button above the battery.''
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Slide the battery cover off, remove the battery and wait '''10''' seconds.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#Hold the reset button for an additional '''2''' seconds and release. The contact sensor should begin flashing blue.
 
#*'''NOTE:''' ''The reset button is a small black button above the battery''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>GD-00Z-1</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Unplug your device and wait '''10''' seconds
 
#Restore power to the device
 
#Press the Link (Z-Wave) button on the left side of the device '''5''' times within '''10''' seconds to reset your device.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Perform a factory reset before attempting to join the Z-Wave network.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Ensure your Iris Garage Door Controller is plugged in, and the tilt sensor battery is active/working.
 
#Press the Link (Z-Wave) button once located on the left of the Iris Garage Door Controller.
 
#When your device triple beeps, it has successfully joined the Z-Wave network.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Once the controller is ready to exclude your device, press the Link (Z-Wave) button once located on the left side of the device.
 
#The garage door controller should give a short beep immediately followed by a long beep.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Keypad</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3405-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the battery and wait '''10''' seconds.
 
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for '''2''' seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
 
#You may now insert the 2nd battery.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform a factory reset before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for '''2''' seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
 
#You may now insert the 2nd battery.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V3 Keypad</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>iL02_1</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove only 1 AA battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Remove only 1 AA battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove only 1 AA battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
 
#A flashing Blue light indicates the device is reset and ready to pair again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Motion Sensor</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3326-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the battery and wait '''10''' seconds
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
 
#Hold for an additional '''2''' seconds and release.
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
 
#Upon a successful reset your device will now be flashing Blue, indicating it's ready to pair.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Factory reset the device before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery for '''10''' seconds and re-insert.
 
#Replace the battery cover. The sensor's Blue LED will flash while searching for the hub.
 
#Once paired the LED will stop flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
 
#Hold for an additional '''2''' seconds and release.
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
 
#Upon a successful reset your device will now be flashing Blue, indicating it's ready to pair.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V3 Motion Sensor</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>iL07_1</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
 
#A flashing Blue light indicates the device is ready to pair.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
 
#A flashing Blue light indicates the device is ready to pair.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the battery and wait '''10''' seconds.
 
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
 
#A flashing Blue light indicates the device is ready to pair.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Smart Plug</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3210-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the Smart Plug from the outlet and wait '''10''' seconds.
 
#Press and hold the small white button on the front of the plug.
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#As soon as the LED on the front of the plug lights up, release the button.
 
#If the reset was successful the Blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Factory reset the device before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert your smart plug into any wall outlet. Your smart plug should be flashing Blue, that means it's in pairing mode.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press and hold the small white button on the front of the plug.
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#As soon as the LED on the front of the plug lights up, release the button.
 
#If the reset was successful the Blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>V2 Smart Fob</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3450-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Twist open the battery cover on the back of the Smart Fob.
 
#Remove the battery and wait '''10''' seconds
 
#Reinstall the battery with the positive side facing you.
 
#Once the battery is installed, push any of the four buttons '''8''' times in a row, once per second.
 
#Confirm that the fob has been reset by checking that the fob's background light is flashing Blue. If it does not do this, check the battery and retry from step 2.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Factory reset the device before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
 
#The Smart Fob's LED will flash Blue while searching for the hub.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Twist open the battery cover on the back of the Smart Fob.
 
#Remove the battery and wait '''10''' seconds
 
#Reinstall the battery with the positive side facing you.
 
#Once the battery is installed, push any of the four buttons '''8''' times in a row, once per second.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>IRIS</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Water Sensor</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>3315-L</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Remove the cover from the sensor, then remove the battery for at least '''10''' seconds.
 
#Press and hold the reset button while reinserting the battery.
 
#Hold for an additional '''2''' seconds and release.
 
#A successful reset will be indicated by a flashing Blue light on your sensor
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Factory reset the device before attempting to pair.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery and wait '''10''' seconds.
 
#Re-insert the battery
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the cover from the sensor, then remove the battery for at least '''10''' seconds.
 
#Press and hold the reset button while reinserting the battery.
 
#Hold for an additional '''2''' seconds and release.
 
#A successful reset will be indicated by a flashing Blue light on your sensor
 
 
 
<hr />
 
 
 
=='''<big>KEEN Home</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>KEEN Home</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Vent</big>''' </div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Vent</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
 
#You will know that the Smart Vent has been properly reset when the LED starts double flashing Green
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Removed the battery cartridge and reinsert it to bring the vent online.
 
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
 
#This should force the vent into join-mode once again.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
 
#You will know that the Smart Vent has been properly reset when the LED starts double flashing Green
 
 
 
<hr />
 
=='''<big>Kwikset</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
 
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove battery pack
 
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for '''30''' seconds until the lock beeps and the status LED flashes Red.
 
#Press the Program button once more. When the LED flashes Green and you hear one beep, the lock has been reset.
 
#Perform the '''door handing''' process again.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait '''15''' seconds, before attempting the handing process again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of '''60''' seconds during the Inclusion process.
 
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system, repeat the Inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of '''60''' seconds during the Inclusion process.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Kwikset</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartCode</big>'''</div>
 
|<div style="text-align: center;">'''<big>910 / 912 / 914</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove battery pack
 
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for '''30''' seconds until the lock beeps and the status LED flashes Red.
 
#Press the Program button once more. When the LED flashes Green and you hear one beep, the lock has been reset.
 
#Perform the '''door handing''' process again.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait '''15''' seconds, before attempting the handing process again.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave controller
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press button '''A''' on the lock '''4''' times to pair it. The controller and lock must remain stationary for a total of '''60''' seconds during the pairing process.
 
#*If pairing is unsuccessful, press button '''B''' on the lock '''9''' times and repeat the pairing process.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press button '''B''' on the lock '''9''' times'''.'''
 
 
 
<hr />
 
 
 
=='''<big>Leak Intelligence</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Leak Intelligence</big>'''</div>
 
|<div style="text-align: center;">'''<big>Leak Gopher</big>''' </div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Unplug your device and wait '''10''' seconds
 
#Restore power to the device
 
#Press the Link (Z-Wave) button on the left side of the device '''5''' times within '''10''' seconds to reset your device.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave button once.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Once the controller is ready to exclude your device, press the Z-Wave button once.
 
 
 
<hr />
 
=='''<big>Leviton</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Leviton</big>'''</div>
 
|<div style="text-align: center;">'''<big>Plug-in Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>DZPA1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#On the 4-Scene controller, press and hold buttons '''1''' and '''3'''.
 
#Wait approximately '''5''' seconds until the LED turns amber and then solid red.
 
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Enter programming mode by holding the control button for 7 seconds until the locator LED blinks '''Amber'''.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Tap the locator button one time and the locator LED will quickly flash green.
 
#Upon sucessful inclusion to the Z-Wave network, the LED will turn off and then flash '''Green''' 3 times.
 
#If inclusion fails, the LED will flash '''Red''' 3 times.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter programming mode by holding the control button for 7 seconds until the locator LED blinks '''Amber'''.
 
#Tap the locator button one time and the locator LED will quickly flash green.
 
#The device will be excluded from the Z-Wave network.
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Leviton</big>'''</div>
 
|<div style="text-align: center;">'''<big>4-Scene Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>VRCS4</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#On the 4-Scene controller, press and hold buttons '''1''' and '''3'''.
 
#Wait approximately '''5''' seconds until the LED turns amber and then solid red.
 
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
'''Leaving the Z-Wave Network'''<hr />
 
 
 
=='''<big>Linear</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door / Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>WADWAZ-1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*'''See [[Discovering your Devices|Discovering your devices]] for detail instructions.'''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Depress the Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Tamper switch of WADWAZ-1 for '''1''' second and release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 
|<div style="text-align: center;">'''<big>PIR Motion Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>WAPIRZ-1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Depress the Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Tamper switch of WAPIRZ-1 for '''1''' second and release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Linear (GoControl)</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren / Strobe</big>'''</div>
 
|<div style="text-align: center;">'''<big>WA105DBZ-1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Factory reset is achieved by performing a general exclusion.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the siren/strobe Program/Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Exclusion the Z-Wave Network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the siren/strobe Program/Tamper switch for '''1''' second then release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
 
 
<hr />
 
=='''<big>Lutron</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">'''<big>Brand</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device</big>'''</div>
 
|<div style="text-align: center;">'''<big>Product Number</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device Type</big>'''</div>
 
|<div style="text-align: center;">'''<big>Protocol</big>'''</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Aurora</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly press the center button '''3''' times and hold on the thrid press for aproximatley '''6''' seconds until the LED flashes.
 
#Once LED is flashing quickly tap button '''3''' time again.
 
#The LED will flash rapidly to indicate the device has been successfuly reset for factory defaults.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly press the center button on the Aurora '''2''' times to begin pairing.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Dimmers and Switches</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Dimmer / Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Caséta Smart Bridge Pro</big>'''</div>
 
|<div style="text-align: center;">'''<big>L-BDGPRO2</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bridge</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Network Reset'''
 
 
 
#First, press and hold the black button on the back of your Smart Bridge for '''20''' seconds.
 
 
 
'''Factory Reset'''
 
 
 
#Quickly tap the button '''3''' times and hold. '''DO NOT release after the third tap'''.
 
#Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
 
#Release the button and quickly tap the button '''3''' times. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
 
#The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
 
 
 
'''NOTE''': ''Lutron does not recommend factory resetting a Smart Bridge Pro unless advised by a member of the Lutron technical support team.''<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Pico Remote</big>'''</div>
 
|<div style="text-align: center;">'''<big>PJ2-</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Radio RA2 Keypads</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Release the button, then immediately tap the button '''3''' more times.
 
#The RA2 keypad has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Radio RA2 Main Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>RR-MAIN-REP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the Test button on a Main Repeater '''3''' times. '''DO NOT release the button after the third tap.'''
 
#Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately '''3''' seconds).
 
#Release the Test button and immediately tap '''3''' times again. All the LEDs will flash Red quickly.
 
#When the LEDs stop flashing, the Main Repeater has been returned to factory settings
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Radio RA2 Occupancy Sensors</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
*'''Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)'''
 
 
 
#Quickly tap '''3''' times and hold the Test, Lights ON, or Lights OFF button on the Sensor. '''DO NOT release after third tap'''.
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 
#Release the button and tap it again '''3''' times until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
 
 
*'''Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)'''
 
 
 
#Quickly tap '''3''' times and hold the Test or Light button on the Sensor. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 
#Release the button and tap '''3''' times again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
 
 
*'''Radio Powr Savr™ Occupancy/Vacancy Wall-Mounted Sensor'''
 
 
 
#Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
 
#Release the button and tap it again '''3''' times until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Radio RA2 Select Main Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>RR-SEL-REP2</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly tap '''3''' times and hold down any button on the Main Repeater. '''DO NOT release after the third tap.'''
 
#Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash Red slowly (approximately once per second).
 
#Release the button and quickly tap '''3''' times again. The Main Repeater LEDs will flash Green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Main Repeater and system components have now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device.<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>RadioRA2 VCRX Visor Control Receiver</big>'''</div>
 
|<div style="text-align: center;">'''<big>RR-VCRX</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Quickly tap '''3''' times and hold any button (except Learn) on the VCRX. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
 
#Release the button and tap '''3''' times again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The VCRX has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device.<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Serena Shades</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Shade Control</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the shade button quickly '''3''' times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
 
#Immediately tap the shade button quickly '''3''' more times, until the shade button LED flashes '''Green''' rapidly, then flashes '''Red/Green''' '''3''' times, and turns off.
 
#The Serena shade has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Sivoia QS Triathlon Shades</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Shade Control</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the shade button quickly '''3''' times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
 
#Immediately tap the shade button quickly '''3''' more times, until the shade button LED flashes '''Green''' rapidly, then flashs '''Red/Green''' '''3''' times, and turns off.
 
#The Sivoia shade has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>RadioRA2 Fan Control</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>RRD-2ANF</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the tapswitch '''3''' times on a control. '''DO NOT release after the third tap.'''
 
#Keep the tapswitch pressed on the third tap (for approximately '''3''' seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
 
#Release the tapswitch and immediately tap it '''3''' times again.
 
#The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device.<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lutron</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Caséta Fan Control</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>PD-FSQN</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Fan Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lutron Clear Connect</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
 
 
'''Join the Lutron Clear Connect network'''
 
 
 
#See the [[Lutron Integrator|Lutron Integrator documentation]].
 
 
 
'''Leaving the Lutron Clear Connect network'''
 
 
 
#From the device's details page, select Remove Device, then Remove
 
#Perform a factory reset on the device
 
 
 
<hr />
 
=='''<big>LUX</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Lux</big>'''</div>
 
|<div style="text-align: center;">'''<big>KONOz</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Access the installation settings by going to the main menu and selecting the gear icon.
 
#You will see “IS” on the screen and will be prompted to select “yes” or “no”.
 
#Select “yes” to access the  installation settings.
 
#Rotate the knob to view settings and press the knob to confirm.
 
#Once in the installer settings, rotate the knob to '''99'''.
 
#Press the knob to confirm, then press and hold the knob for '''3''' seconds.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Perform factory reset.
 
#KONOz is now ready to be configured for your heating and cooling system. The KONOz will guide you through the initial system configuration.
 
#After confirming your system settings, KONOzwill ask if you would like to connect to a Smart Hub. Select “SET” to establish a connection.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Perform factory reset.
 
 
 
<hr />
 
=='''<big>MCO Home</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>MCO Home</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>MH-DT311</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press '''10''' times of any button or exclude the device from Z-Wave network, then cut off the main power.
 
#The factory setting will be restored.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press 3 times on "+" or "-" button to add the device. If successful, the green LED flashes '''4''' times.
 
#*Note: If an external switch is wired to the dimmer, you may also toggle that '''3''' times to add the device to the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED flashes '''4''' times.
 
#*Note: If an external switch is wired to the dimmer, you may also toggle that '''3''' times to add the device to the network.
 
 
 
<hr />
 
=='''<big>Monoprice</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Door/Window Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>24259</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#To reset the sensor, press and hold the Z-button for about '''20''' seconds.
 
#The LED will change from steadily illuminated to flashing then back to steadily illuminated, indicating that the reset operation was successful.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Rapidly press the Z-button '''3''' times to include the device in the network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Rapidly press the Z-button '''3''' times to exclude the device from the network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Plug-In Dimmer</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>11994</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device, returning the device to a factory state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to include the device in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Plug-In ON/OFF</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>11995</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device, returning the device to a factory state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to include the device in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Recessed Door/Window sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>15268</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Z-button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for '''2''' seconds and then turn off.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-button on your Sensor. If your switch has been successfully unlinked to your network, its LED will start to flash for a short time.
 
#If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Door/Window Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>15270</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device and return it to a factory state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>PIR Motion Sensor with Temperature</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>15271</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device and return it to a factory state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Plug-in Outlet</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>15654</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
 
 
'''Factory Reset'''
 
 
 
#Press and hold the Z-button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#If the plug-in has not already been included into a Z-Wave network, the LED indicator will flash rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can join the Hubitat Elevation™ Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click the Z-Button '''3''' times. The plug-in will be removed from your Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>4 in 1 motion sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>15902</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network and has returned it to a factory state.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Momentarily press the '''Program Switch'''
 
#The LED should flash '''5''' times indicating the sensor has not yet been included in the Z-Wave network.
 
#If the LED flashes only '''1''' time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
 
#Momentarily press the button again after it flashes '''5''' times, to automatically include the sensor in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program button, the LED will flash, indicating the sensor is no longer joined to the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Monoprice</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Smart Plug and Repeater</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>27481</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Press and hold the Z-Button on the smart plug for more than '''20''' seconds.
 
#The LED indicator will illuminate Yellow steadily for about '''2''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Rapidly press the Z-button '''3''' times to include the device in the network.
 
 
 
'''Testing the Smart Plug Z-Wave connection'''
 
 
 
You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.
 
 
 
To begin testing, press and hold the Z button for '''6-9''' seconds, releasing the button when the RGB LED illuminates violet.
 
 
 
*'''''Note'':''' The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
 
**'''Flashing Green''': The RGB LED will flash Green while the smart plug is attempting to establish a connection with the main controller.
 
**'''Solid Green''': The RGB LED will illuminate Green for about '''2''' seconds to indicate that direct communications are stable.
 
**'''Flashing Orange''': The RGB LED will flash Orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
 
**'''Solid Orange''': The RGB LED will illuminate Orange for about '''2''' seconds to indicate that the communication quality is moderate.
 
**'''Solid Red''': The RGB LED will illuminate Red for about '''2''' seconds to indicate that they communications attempt has failed.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Rapidly press the Z-button '''3''' times to exclude the device from the network.
 
#The RGB LED will flash Orange while the smart plug is being removed.
 
#The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate Orange steadily for about '''2''' seconds.
 
 
 
<hr />
 
==<big>'''NanoLeaf'''</big>==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NanoLeaf</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Light Panels</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Aurora / Canvas</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>LAN</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Disconnect power to the Nanoleaf Light Panels.
 
#Hold the Toggle and Power buttons together and reconnect the power without releasing the buttons.
 
#After about '''7''' seconds, the WiFi status LED will start to flash rapidly.
 
#Once the flashing begins, you can release the buttons.
 
#You must then wait '''3''' minutes for the Nanoleaf Light Panels to reset to factory default settings and boot-up.
 
 
 
'''Join the LAN'''
 
 
 
#Use the '''NanoLeaf Smarter Series''' app from your mobile device to setup your light panels on the WiFi network.
 
#From the Hubitat Web Interface home page, select '''Devices''', then '''Add Virtual Device'''
 
#*See [[Devices]] for further detail.
 
#Name your device and select '''Nanoleaf Aurora''' from the device ''Type'' drop-down menu, and press '''Save'''.
 
#In the Preferences field of the driver, enter the IP address of your Nanoleaf panel.
 
#*'''NOTE:''' You should reserve the IP address for your NanoLeaf light panels in your router just as you do for your Hubitat Elevation™ hub. If you do not, the IP address will change when the DHCP lease on your router expires for connected IP devices. The result will be that the NanoLeaf Aurora driver will no longer be able to find your device.
 
#Press '''Save''' again in the driver.
 
#One your NanoLeaf panel, press the pairing button.
 
#In the NanoLeaf Aurora driver, press the '''Get Auth Token''' button.
 
#Test your panel for proper operation.
 
#*
 
 
 
'''Leaving the LAN'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Plug your Light Panels into power. After a '''1''' minute bootup sequence the panels will show the last scene that was playing
 
#Press and hold down the '''Effect Select''' and '''Power''' buttons on the controller for about '''10''' seconds, until the LED on the controller begins flashing
 
#Release the two buttons and the LED on the controller will remain on and steady
 
#Delete the previous device from the app and setup once again
 
<hr />
 
=='''<big>Neo</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">'''<big>Brand</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device</big>'''</div>
 
|<div style="text-align: center;">'''<big>Product Number</big>'''</div>
 
|<div style="text-align: center;">'''<big>Device Type</big>'''</div>
 
|<div style="text-align: center;">'''<big>Protocol</big>'''</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Door/Window Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-DS01ZE</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove tlease expires for the assigned IP address.
 
#
 
#he cover of contact sensor main body.
 
#Make sure the sensor is connected to power source.
 
#Press and hold the reset button for '''10''' seconds, the LED light will flash Red once.
 
#Release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The contact sensor will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Door/Window Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-DS02ZU</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the cover of contact sensor main body.
 
#Make sure the sensor is connected to power source.
 
#Press and hold the reset button for '''10''' seconds, the LED light will flash Red once.
 
#Release the button.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The contact sensor will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Motion Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-PD01ZU-T</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the sensor’s cover.
 
#Make sure the sensor is connected to power source.
 
#Press the code button for '''10''' seconds, the LED will flash Red once.
 
#Release the code button.
 
#*'''NOTE:''' When the PIR is being restored to factory settings, please make sure a power source is connected.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The motion sensor will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Power Plug</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-WR02Z</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the code button on the front of the outlet for '''10''' seconds.
 
#When the LED flashes, release the button.
 
#When the outlet has been reset, the LED will flash on and off '''5''' times within a '''2''' second period.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The device will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the code button '''3''' times, the LED light will flash for '''5''' times and the device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>One Key SOS</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-RC03ZU</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the code button for '''10''' seconds.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the Red SOS alarm button '''3''' times.
 
#The device will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the Red SOS alarm button '''3''' times and the device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Neo</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>One Key SOS and Remote Control</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NAS-RC03ZU</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press and hold the code button for '''10''' seconds.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Quickly click the Red SOS alarm button '''3''' times.
 
#The device will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly click the Red SOS alarm button '''3''' times and the device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>NodOn</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NodOn</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Octan Remote</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>CRC-3US-1</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#A simultaneous long press ('''1''' second) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#Push on the '''solid circle''' within '''10''' seconds.
 
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure.
 
#The device will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#Push on the '''solid circle''' within '''10''' seconds.
 
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NodOn</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Soft Remote</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>CRC-3US-6</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#A simultaneous long press ('''1''' second) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#Push on the '''solid circle''' within '''10''' seconds.
 
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure.
 
#The device will be detected and included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#Push on the '''solid circle''' within '''10''' seconds.
 
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure
 
#The device will be excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>NYCE</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Curtain Motion Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NCZ-3045-HA</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Press the button '''4''' times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''3''' Green flashes indicate the device has successfully joined the network.
 
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Ceiling Motion Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NCZ-3043-HA</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Press the button '''4''' times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''3''' Green flashes indicate the device has successfully joined the network.
 
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the Mounting Plate by rotating the Housing counter-clockwise as shown.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Motion Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NCZ-3041-HA</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Press the button 4 times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''3''' Green flashes indicate the device has successfully joined the network.
 
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens,  ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#To open the battery cover, use a flathead screwdriver in the recessed slot at the bottom of the sensor housing.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Garage Door (Tilt) Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NCZ-3014-HA</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Press the button 4 times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''3''' Green flashes indicate the device has successfully joined the network.
 
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed, and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Slide open the Garage Door (Tilt) Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>NYCE</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Door/Window Sensor</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>NCZ-3011-HA</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide open the Door/Window Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Slide open the Door/Window Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Press the button 4 times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''3''' Green flashes indicate the device has successfully joined the network.
 
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed, and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Slide open the Door/Window Sensor’s top housing.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
 
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
 
 
 
<hr />
 
=='''<big>Orbit</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Orbit</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>Smart Hose Faucet Timer</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>27087</big>'''</div>
 
|<div style="text-align: center;">'''<big>Irrigation Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Insert two AA alkaline batteries and re-insert the tray.
 
#Press the RESET button '''5''' times in rapid secession.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Slide out the battery tray on the back of the timer.
 
#Insert two AA alkaline batteries and re-insert the tray.
 
#*'''NOTE:''' Firmly replace the battery tray to ensure water resistance and increase battery life. You will know the battery tray is fully inserted if it does not pull out easily.
 
#Turn the dial to '''AUTO'''.
 
#When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
 
#*'''NOTE:''' The timer will remain in pairing mode for '''10''' minutes or until paired'''.''' If pairing is not successful after '''10''' minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button '''5''' times in rapid secession.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press the RESET button '''5''' times in rapid secession.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Orbit</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>12-Station Sprinkler Controller</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>27396</big>'''</div>
 
|<div style="text-align: center;">'''<big>Irrigation Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Ensure the controller is connected to power.
 
#Press the SYNC button '''5''' times in rapid secession.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Ensure the controller is connected to power.
 
#Turn the dial to '''AUTO'''.
 
#When the controller is first connected to power, it will automatically attempt to connect.
 
#*'''NOTE:''' If pairing is not successful after '''10''' minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button '''5''' times in rapid succession
 
#The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words '''SMART MODE''' will appear on the screen.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the <nowiki/>device details page to confirm proper operation
 
 
 
'''Leaving the Zigbee Netwo'''<nowiki/>'''rk'''
 
 
 
#From the device's detail<nowiki/>s page, select '''Remove Device''', then '''Remove'''.
 
#Press the RESET button '''5'''<nowiki/> times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for '''5''' seconds to cancel re-pairing.
 
<hr />
 
 
 
=='''<big>Orvibo</big>'''==
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Obvibo</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>SN11</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 
#This will disconnect the sensor from the Zigbee network.
 
#Short-press the reset button and the '''Green light''' will flash slowly.
 
#The sensor is now in pairing mode.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Remove the cover by rotating it counterclockwise
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 
#This will disconnect the sensor from the Zigbee network.
 
#Short-press the reset button and the '''Green light''' will flash slowly.
 
#The sensor is now in pairing mode.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold down the reset button on the front of the motion sensor until the '''Green light''' goes out.
 
#This will disconnect the sensor from the Zigbee network.
 
 
 
<hr />
 
=='''<big>OSRAM</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Osram</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lightify Flex RGBW</big>'''</div>
 
|<div style="text-align: center;">'''<big>73698</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat '''5''' times - Unplug for '''1''' second and then plug in for '''1''' second
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset and ready for pairing.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat 5 times - Unplug for '''1''' second and then plug in for '''1''' second
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset and ready for pairing.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat 5 times - Unplug for '''1''' second and then plug in for '''1''' second
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset and ready for pairing.
 
 
 
<hr />
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Osram</big>'''</div>
 
|<div style="text-align: center;">'''<big>All smart bulbs</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Turn the light off
 
#Turn the light on for three '''3''' seconds
 
#Turn the light off
 
#Repeat this cycle '''5''' times
 
#Wait 10 seconds for the light to flash '''3''' times
 
#Repeat these steps if the light does not flash three times
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Turn the light off
 
#Turn the light on for three '''3''' seconds
 
#Turn the light off
 
#Repeat this cycle '''5''' times
 
#Wait 10 seconds for the light to flash '''3''' times
 
#Repeat these steps if the light does not flash '''3''' times
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Turn the light off
 
#Turn the light on for three '''3''' seconds
 
#Turn the light off
 
#Repeat this cycle '''5''' times
 
#Wait 10 seconds for the light to flash '''3''' times
 
#Repeat these steps if the light does not flash '''3''' times
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Osram</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Outdoor Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>G11028081</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
'''NOTE:''' ''Reset method may vary by firmware version''
 
 
 
'''Method 1'''
 
 
 
#Hold the button for '''30''' seconds
 
#The outdoor plug will click '''5''' times
 
#The outdoor plug is now reset and ready for pairing
 
 
 
'''Method 2'''
 
 
 
#Turn the outdoor plug off
 
#Turn the outdoor plug on for three '''5''' seconds
 
#Turn the outdoor plug off
 
#Repeat this cycle '''5''' times
 
#The outdoor plug is now reset and ready for pairing
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#See factory reset instructions above to reset the outdoor plug and ready it for pairing . The required steps will vary by firmware version.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#See factory reset instructions above. The required steps will vary by firmware version.
 
 
 
<hr />
 
=='''<big>Philips Hue</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Philips Hue</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Button</big>'''</div>
 
|<div style="text-align: center;">'''<big>046677553715</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Turn the smart button over and remove the back cover. Use a straightened paperclip to press the '''setup''' button on the back for 5 seconds. An LED on the front of the sensor will flash once to confirm factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Turn the smart button over and remove the back cover. Use a straightened paperclip to press the '''setup''' button on the back for 5 seconds. An LED on the front of the sensor will flash once to confirm reset.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button until the LED on the front of the button is flashing.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Turn the smart button over and remove the back cover. Use a straightened paperclip to press the '''setup''' button on the back for 5 seconds. An LED on the front of the sensor will flash once to confirm factory reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Philips Hue</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>73698</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Turn the dimmer switch over and use a straightened paperclip to press the '''setup''' button on the back for '''1''' second.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Turn the dimmer switch over and use a straightened paperclip to press the '''setup''' button on the back for '''1''' second.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Turn the dimmer switch over and use a straightened paperclip to press the '''setup''' button on the back for '''1''' second.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Philips Hue</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>473389</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#On the back of the motion sensor, and use a straightened paperclip to press the '''setup''' button for '''1''' second.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#On the back of the motion sensor, and use a straightened paperclip to press the '''setup''' button for '''1''' second.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#On the back of the motion sensor, and use a straightened paperclip to press the '''setup''' button for '''1''' second.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Philips Hue</big>'''</div>
 
|<div style="text-align: center;">'''<big>All Hue Lights</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#You must use a Hue Dimmer to factory reset a Hue bulb, light fixture or LED strip that is not attached to a Hue bridge.
 
#Turn on the light on to be reset, ensuring other bulbs within a few inches are unscrewed or unplugged or they may be reset too.
 
#Hold the remote within '''4''' inches of the light.
 
#Press and hold the 1st (On / I in some countries) and the and 4th (Off / O in some countries) buttons simultaneously for about '''10''' seconds, until the light starts flashing on and off.
 
#When the light stops flashing, it will remain ON at full brightness, and the green LED on the remote will flash green, indicating the bulb has been factory reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#Using a Hue dimmer, factory reset the light as described above.
 
#Disconnect the light from mains power.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Power on the light
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Using a Hue dimmer, factory reset the light as described above.
 
 
 
<hr />
 
=='''<big>Qubino</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush 1 Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHAD3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''5''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''5''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''5''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush 1D Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHND3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''5''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''5''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush 2 Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHBD3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''5''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush Shutter DC</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHOD3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''3''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush Shutter</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHCD3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''5''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush ON/OFF Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHID3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''5''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than '''6''' seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds. The device has to get On/Off signal '''3''' times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Qubino</big>'''</div>
 
|<div style="text-align: center;">'''<big>Flush Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZMNHDD3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Connect the device to the power supply
 
#Within the first '''60''' seconds the device is connected to the power supply, toggle the switch connected to the I1 terminal '''5''' times within '''3''' seconds ('''5''' times change switch state).
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button for more than 6 seconds.
 
 
 
*'''NOTE:''' ''By resetting the device, all custom parameters previously set on the device will return to their default values, and the owner ID will be deleted.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Connect the device to the power supply (with the temperature sensor already connected*).
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds. The device has to get On/Off signal 3 times, meaning '''3''' times push on the push button or '''6''' times flip of a switch.
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between '''2-6''' seconds
 
 
 
*'''NOTE:''' *If connecting the temperature sensor, switch off the power supply and make sure the device is excluded from your network BEFORE connecting the sensor
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch connected to the I1 terminal '''3''' times within '''3''' seconds
 
#*If the device is powered by 24 V SELV supply, press and hold the S (Service) button between
 
 
 
<hr />
 
=='''<big>Quotra</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Quotra</big>'''</div>
 
|<div style="text-align: center;">'''Wireless Smart Dimmer'''</div>
 
|<div style="text-align: center;">
 
'''<big>B07CVL9SZF</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold the power button for '''10''' seconds.
 
#Rlease when the LED slowly fades in and out (this will only happen for 3 seconds).
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the power button for '''10''' seconds.
 
#Rlease when the LED slowly fades in and out (this will only happen for 3 seconds).
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold the power button for '''10''' seconds.
 
#Rlease when the LED slowly fades in and out (this will only happen for 3 seconds).
 
 
 
<hr />
 
=='''<big>Radio Thermostat Company of America</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Radio Thermostat Company of America</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>CT-101</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#The thermostat must be in OFF mode.
 
#Wait until the radio wave icons on the left side of the screen stop flashing then touch the screen once to turn on the back light and then hold the center of the screen for about '''8''' seconds until the thermostat beeps.
 
 
 
'''Factory Reset''' '''(Alternate Method)'''
 
 
 
#Place the CT101 in the off position by pressing mode button until '''OFF''' is shown at the top left of the screen.
 
#Press the menu button
 
#Press and hold the center of the screen for about 5 sec or until the screen changes then release.
 
#You will see two arrows. First press the up arrow and wait for the count down.
 
#Now press the down arrow and again, wait for the count down.
 
#All parameter values will be restored to defaults and a message is sent to any radio module installed to instruct the module to restore its own default values.
 
#*The thermostat will now resets itself.
 
#Press the house to get back to the main screen.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press/Touch the MATE button on the MENU screen. A large '''r1''' will be displayed.
 
#This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
 
#When a device has joined a network the LINK icon will appear under the radio tower.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press/Touch the MATE button on the MENU screen. A large '''r1''' will be displayed.
 
#This will bring you to the network include screen. Confirm by touching MATE again to initiate the mating process. The MATE icon and the status indicator LEDs will flash.
 
#When a device has excluded from the network, the LINK icon will disappear under the radio tower.
 
 
 
<hr />
 
=='''<big>Remotec</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Remotec</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay / Fixture Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZFM-80US/DA065</big>'''</div>
 
|<div style="text-align: center;">'''<big>Relay</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Factory reset is accomplished by excluding the device from the Z-Wave netowrk
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click once on the PROG button or and external attached switch.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Click once on the PROG button or and external attached switch.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click once on the PROG button or and external attached switch.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Remotec</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZRC-90 Scene Master</big>'''</div>
 
|<div style="text-align: center;">'''<big>REMEZRC90</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and keep holding '''R''' button not less than '''10''' seconds.
 
#Release '''R''' button then triple click on the same '''R''' button within 2 seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press '''L''' & '''R''' buttons simultaneously until the LED lights up to add the device to the Z-Wave network. The LED will keep flashes slowly.
 
#Press the program button. The LED will flash once, then remain off if the device is included into the Z-Wave network.
 
#If the LED flashes '''6''' times rapidly, then remains off, the device has failed to be included in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Click once on the '''R''' button to remove the device from the Z-Wave network. The LED will continue flashing slowly.
 
#Press the program button. The LED will flash once, then remain off if the device is excluded from the Z-Wave network.
 
#If the LED flashes '''6''' times rapidly, then remains off, the device has failed to be excluded in the Z-Wave network.
 
#Perform a factory reset and repeat the above steps to exclude the device from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>RGBgenie</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>RGBgenie</big>'''</div>
 
|<div style="text-align: center;">'''<big>Single color remote</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW-5121</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold the middle (Light ON) button.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the middle (Light ON) button.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold the middle (Light ON) button.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>RGBgenie</big>'''</div>
 
|<div style="text-align: center;">'''<big>RGB color remote</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW-5122</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold the middle (Light ON) button.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the middle (Light ON) button.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold the middle (Light ON) button.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>RGBgenie</big>'''</div>
 
|<div style="text-align: center;">'''<big>Monochrome controller panel</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZB-3026</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold down the power button on the Touch Panel until the LED indicator turns on.
 
#Immediately press the power button '''5''' times.
 
#The LED indicator will flash '''3''' times quickly to indicate successful removal from the network and is now reset to factory default.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the '''power button''' until the LED status indicator turns on.
 
#Immediately press the '''S1''' button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
 
 
 
'''Verifying network pairing'''
 
 
 
#Quickly press any button and the LED indicator should flash once.
 
#If the LED indicator does not respond, the Touch Panel is not paired with a network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>RGBgenie</big>'''</div>
 
|<div style="text-align: center;">'''<big>3 Zone Color Touch Panel</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZB-5027</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold down the power button on the Touch Panel until the LED indicator turns on.
 
#Immediately press the power button '''5''' times.
 
#The LED indicator will flash '''3''' times quickly to indicate successful removal from the network and is now reset to factory default.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the '''power button''' until the LED status indicator turns on.
 
#Immediately press the '''S1''' button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
 
 
 
'''Verifying network pairing'''
 
 
 
#Quickly press any button and the LED indicator should flash once.
 
#If the LED indicator does not respond, the Touch Panel is not paired with a network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>RGBgenie</big>'''</div>
 
|<div style="text-align: center;">'''<big>Color Remote</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZB-5028</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold down the power button on the Touch Panel until the LED indicator turns on.
 
#Immediately press the power button '''5''' times.
 
#The LED indicator will flash '''3''' times quickly to indicate successful removal from the network and is now reset to factory default.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the '''power button''' until the LED status indicator turns on.
 
#Immediately press the '''S1''' button once to enable the Touch Panel to search for nearby networks. The LED indicator will flash once every second.
 
 
 
'''Verifying network pairing'''
 
 
 
#Quickly press any button and the LED indicator should flash once.
 
#If the LED indicator does not respond, the Touch Panel is not paired with a network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
 
 
<hr />
 
=='''<big>Salus</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Salus</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Plug</big>'''</div>
 
|<div style="text-align: center;">'''<big>SP-600</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press the button on the outlet for '''10''' seconds.
 
#The light surrounding the button will flash Red '''5''' times, and will then go out.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button on the outlet for '''10''' seconds.
 
#The light surrounding the button will flash Red '''5''' times, and will then go out.
 
#If the device is not discovered by Hubitat Elevation™, then unplug the outlet for 10 seconds and plug it in again. It should now be discovered by the hub.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press the button on the outlet for '''10''' seconds.
 
#The light surrounding the button will flash Red '''5''' times, and will then go out.
 
 
 
<hr />
 
=='''<big>Samsung SmartThings</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet 2017</big>'''</div>
 
|<div style="text-align: center;">'''<big>F-OUT-US-2</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED starts flashing '''Blue'''.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Make sure the Outlet is within '''15''' feet ('''4.5''' meters) of the hub during setup.
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED starts flashing '''Blue'''.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED starts flashing '''Blue'''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet V5</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM6001-OTP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED flashes '''Blue''' 3 times.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED flashes '''Blue''' 3 times'''.'''
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the '''Connect''' button for '''5''' seconds, and release it when the LED flashes '''Blue''' 3 times.
 
 
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button V5</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM6001-BTP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing '''Red'''.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the recessed connect button for '''5 seconds.'''
 
#Release the button when the LED starts flashing '''Red.'''
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing '''Red'''.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor V5</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM6001-MTP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash red and green while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Leak Sensor V5</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM6001-WLP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Samsung SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi Sensor V5</big>'''</div>
 
|<div style="text-align: center;">'''<big>IM6001-MPP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash red and green while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
 
 
<hr />
 
=='''<big>Schlage</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Schlage</big>'''</div>
 
|<div style="text-align: center;">'''<big>LiNK Deadbolt</big>'''</div>
 
|<div style="text-align: center;">'''<big>BE-369</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Disconnect the 9V battery.
 
#On the lock keypad, press and release the Schlage button.
 
#Reconnect the battery and wait until the Schlage button is no longer lit.
 
#Within '''10''' seconds, press and hold the '''Schlage button''' until it lights Green and the lock beeps.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the '''6''' digit programming code.
 
#Wait for the Schlage button will flash Amber '''3''' times'''.''' It will be accompanied by '''3''' beeps.
 
#Press the '''Schlage button''' and the '''0''' key.
 
#If successful, the '''Schlage button''' will be flashing Amber'''.'''
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the '''6''' digit programming code.
 
#Wait for the Schlage button will flash Amber '''3''' times'''.''' It will be accompanied by '''3''' beeps.
 
#Press the '''Schlage button''' and the '''0''' key.
 
#If successful, the '''Schlage button''' will be flashing Amber'''.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Schlage</big>'''</div>
 
|<div style="text-align: center;">'''<big>LiNK Deadbolt</big>'''</div>
 
|<div style="text-align: center;">'''<big>FE-599</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Disconnect the 9V battery.
 
#On the lock keypad, press and release the Schlage button.
 
#Reconnect the battery and wait until the Schlage button is no longer lit.
 
#Within '''10''' seconds, press and hold the '''Schlage button''' until it lights Green and the lock beeps.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the '''6''' digit programming code.
 
#Wait for the Schlage button will flash Amber '''3''' times'''.''' It will be accompanied by '''3''' beeps.
 
#Press the '''Schlage button''' and the '''0''' key.
 
#If successful, the '''Schlage button''' will be flashing Amber'''.'''
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the '''6''' digit programming code.
 
#Wait for the Schlage button will flash Amber '''3''' times'''.''' It will be accompanied by '''3''' beeps.
 
#Press the '''Schlage button''' and the '''0''' key.
 
#If successful, the '''Schlage button''' will be flashing Amber'''.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Schlage</big>'''</div>
 
|<div style="text-align: center;">'''<big>Connect Deadbolt</big>'''</div>
 
|<div style="text-align: center;">'''<big>BE-468 / BE-469</big>'''</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Disconnect the batteries
 
#Press and hold the outside Schlage button
 
#While holding the outside Schlage button, then reconnect the batteries.
 
#Release the Outside Schlage Button. '''NOTE: If you are moving the lock to a new door, install the lock on that door before continuing.'''
 
#To check that the lock was reset, press the outside Schlage button and enter one of the Default User Codes.
 
#If the reset was successful, the lock will perform a setup routine. Wait until the bolt stops moving. The reset and setup are complete.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Schlage button.
 
#Enter the '''6''' digit programming code.
 
#Press '''0'''
 
#A '''√''' indicates the lock successfully joined the Z-Wave network, while an '''X''' indicates that it did not successfully join the network.
 
 
 
'''Verify Z-Wave connection status from the lock'''
 
 
 
#Remove the battery cover.
 
#Disconnect the battery connector.
 
#While watching the inside Schlage button, reconnect the battery connector.
 
#The inside Schlage button will flash if the lock is enrolled.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Schlage button.
 
#Enter the '''6''' digit programming code.
 
#Press '''0'''
 
#A '''√''' indicates the lock was successfully excluded the Z-Wave network, while an '''X''' indicates that it did not successfully leave the network.
 
 
 
<hr />
 
=='''<big>Sengled</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sengled</big>'''</div>
 
|<div style="text-align: center;">'''<big>Element Bulbs</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Power cycle on and off '''15''' times, '''VERY''' quickly, ending on the ON position.
 
#*'''NOTE:''' An on and off cycle counts as '''1'''
 
#If successful, the bulb will flash '''5''' times, and will then be in pairing mode.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Power cycle on and off '''15''' times, '''VERY''' quickly, ending on the ON position.
 
#*'''NOTE:''' An on and off cycle counts as '''1'''
 
#If successful, the bulb will flash '''5''' times, and will then be in pairing mode.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Power cycle on and off '''15''' times, '''VERY''' quickly, ending on the ON position.
 
#*'''NOTE:''' An on and off cycle counts as '''1'''
 
#If successful, the bulb will flash '''5''' times, and will then be in pairing mode.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sengled</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Window and Door Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>E1D-G73WNA</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#To reset the sensor, use the provided tool, or something equally thin like a paper clip.
 
#Press and hold the reset button inside the unit for '''8''' seconds.
 
#If successful, a Red light on the face of the sensor will flash '''2''' times'''.'''
 
#*'''NOTE:''' After the sensor is reset, you will have one minute to add it to your hub.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#To reset the sensor, use the provided tool, or something equally thin like a paper clip.
 
#Press and hold the reset button inside the unit for '''8''' seconds.
 
#If successful, a Red light on the face of the sensor will flash '''2''' times.
 
#*'''NOTE:''' After the sensor is reset, you will have one minute to add it to your hub.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#To reset the sensor, use the provided tool, or something equally thin like a paper clip.
 
#Press and hold the reset button inside the unit for '''8''' seconds.
 
#If successful, a Red light on the face of the sensor will flash '''2''' times.
 
#*'''NOTE:''' After the sensor is reset, you will have one minute to add it to your hub.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sengled</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi-Color Light Strip</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>E1G-G8E</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''.
 
 
 
#Press and hold the reset button inside the unit for '''10''' seconds.
 
#If successful, the light strip will flash '''5''' times'''.'''
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the reset button inside the unit for '''10''' seconds.
 
#If successful, the light strip will flash '''5''' times'''.'''
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold the reset button inside the unit for '''10''' seconds.
 
#If successful, the light strip will flash '''5''' times'''.'''
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sengled</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Plug</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>E1C-NB6</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''.
 
 
 
#Press and hold the power button for '''15''' seconds.
 
#If successful '''Blue''' indicator light will stay on briefly, and then slowly pulse on and off.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold the power button for '''15''' seconds.
 
#If successful '''Blue''' indicator light will stay on briefly, and then slowly pulse on and off.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold the power button for '''15''' seconds.
 
#If successful '''Blue''' indicator light will stay on briefly, and then slowly pulse on and off.
 
 
 
<hr />
 
=='''<big>Sensative</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sensative Strips</big>'''</div>
 
|<div style="text-align: center;">'''<big>Guard</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Move magnet all the way to the rounded edge, You should see '''1''' short LED flash'''.'''
 
#Move magnet towards center 2 times. You should see '''2''' LED flashes.
 
#On the last pass, leave at rounded edge for '''10''' seconds.
 
#*If successful, you should see '''1''' long LED flash.
 
#*If you do not see any flashes, then the reset process was not completed successfully.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Keep Strips close to its intended location during the add process.
 
#Remove both magnets. '''1''' long flash confirms proper inclusion to the Z-Wave network.
 
#Move the squared magnet away from the squared end and watch the status in the Hubitat Elevation™ device details to ensure proper functionality.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove both magnets. '''1''' long flash confirms proper exclusion to the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sensative Strips</big>'''</div>
 
|<div style="text-align: center;">'''<big>Drip</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Place magnet 2cm from the rounded edge for '''2''' seconds. You should see '''1 short''' LED flash.
 
#Move between logo and the round edge '''2''' times.
 
#On the second pass, leave the magnet here for '''10''' seconds and wait for '''1 long''' LED flash.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Move the Magnet towards the rounded edge until you see '''2''' LED flashes.
 
#Move magnet between logo and rounded edge slowly '''2''' times.
 
#Remove the magnet. If you see '''1''' LED flash, inclusion to the Z-wave network was successful.
 
#If you see '''5 short''' LED flashes, then inclusion has failed and you should perform a factory reset, then repeat the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Move the magnet towards the rounded edge until '''1''' LED flashes.
 
#Move magnet between logo and rounded edge slowly '''2''' times.
 
#Remove the magnet. If you see '''1''' LED flash, it indicates sucessful exclusion from the Z-Wave network.
 
#If you see '''5 short''' LED flashes, then exclusion has failed and you should perform a factory reset, then repeat the exclusion process.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sensative Strips</big>'''</div>
 
|<div style="text-align: center;">'''Comfort'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Temperature Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Place magnet 2cm from the rounded edge for '''2''' seconds. You should see '''1 short''' LED flash.
 
#Move between logo and the round edge '''2''' times.
 
#On the second pass, leave the magnet here for '''10''' seconds and wait for '''1 long''' LED flash.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Move the Magnet towards the rounded edge until you see '''2''' LED flashes.
 
#Move magnet between logo and rounded edge slowly '''2''' times.
 
#Remove the magnet. If you see '''1''' LED flash, inclusion to the Z-wave network was successful.
 
#If you see '''5 short''' LED flashes, then inclusion has failed and you should perform a factory reset, then repeat the inclusion process.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Move the magnet towards the rounded edge until '''1''' LED flashes.
 
#Move magnet between logo and rounded edge slowly '''2''' times.
 
#Remove the magnet. If you see '''1''' LED flash, it indicates sucessful exclusion from the Z-Wave network.
 
#If you see '''5 short''' LED flashes, then exclusion has failed and you should perform a factory reset, then repeat the exclusion process.
 
 
 
<hr />
 
=='''<big>Sinope</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee Thermostats</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Simultaneously press the '''UP''' and '''DOWN''' arrow buttons for '''10''' seconds
 
#On the thermostat display, the radio signal icon will disappear.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Simultaneously press the '''UP''' and '''DOWN''' arrow buttons to initiate device paring.
 
#On the thermostat display, a radio signal icon will flash while connecting, and will remain solid once connected to the hub.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Simultaneously press the '''UP''' and '''DOWN''' arrow buttons for '''10''' seconds.
 
#On the thermostat display, the radio signal icon will disappear.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Small Electrical Load Controller</big>''' </div>
 
|<div style="text-align: center;">
 
'''<big>RM3250ZB</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press the button next to the '''radio signal''' icon for '''10''' seconds.
 
#On the device, the LED next to the radio signal icon will turn off.
 
#All settings will be reset to factory defaults.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button next to the '''radio signal''' icon to initiate device paring.
 
#On the device, the LED next to the radio signal icon will flash while connecting, and will remain solid once connected to the hub.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press the button next to the '''radio signal''' icon for '''10''' seconds.
 
#On the device, the LED next to the radio signal icon will turn off.
 
#All settings will be reset to factory defaults.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Leak Detector</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>WL4200</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the battery cover.
 
#Press the '''Link''' button for '''10''' seconds.
 
#The LED will flash Green.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery cover.
 
#Press the '''Link''' button to initiate device paring.
 
#*The LED will flash Green while connecting.
 
#*The LED will remain solid Green for '''10''' seconds upon sucessful connection.
 
#*If the LED is flashing Red, the connection has failed.
 
#Test the sensor by exposing the electrodes to a damp cloth and observing the device status on Hubitat Elevation™
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the battery cover.
 
#Press the '''Link''' button for '''10''' seconds.
 
#The LED will flash Green.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Leak Detector</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>WL4200S</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the battery cover.
 
#Press the '''Link''' button for '''10''' seconds.
 
#The LED will flash Green.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery cover.
 
#Press the '''Link''' button to initiate device paring.
 
#*The LED will flash Green while connecting.
 
#*The LED will remain solid Green for '''10''' seconds upon sucessful connection.
 
#*If the LED is flashing Red, the connection has failed.
 
#Test the sensor by exposing the electrodes to a damp cloth and observing the device status on Hubitat Elevation™
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the battery cover.
 
#Press the '''Link''' button for '''10''' seconds.
 
#The LED will flash Green.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Valve</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>VA4200WZ</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the battery cover.
 
#Ensure the switch is set to position '''3''' (Zigbee connection)
 
#Plug the valve power adapter into an AC outlet.
 
#Simultanieously press buttons '''A and B''' for '''10''' seconds.
 
#The LED will '''flash GREEN'''
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery cover.
 
#Ensure the switch is set to position '''3''' (Zigbee connection)
 
#Plug the valve power adapter into an AC outlet.
 
#Press the A button to initiate device paring
 
#*The LED will flash Green while connecting
 
#*The LED will remain solid Green for '''10''' seconds upon sucessful connection
 
#*If the LED is flashing Red, the connection has failed.
 
#Test the valve by toggling '''Open''' and '''Close''' in the device detail page on Hubitat Elevation™, and observe that the valve properly opens and closes in response to the pressing to the Open and Close buttons.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the battery cover.
 
#Ensure the switch is set to position '''3''' (Zigbee connection)
 
#Plug the valve power adapter into an AC outlet.
 
#Simultanieously press buttons '''A and B''' for '''10''' seconds.
 
#The LED will flash Green.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sinope</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Dimmer</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>DM2500ZB</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Simultaniouly press the up and down dimmer buttons for '''10''' seconds.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Simultaniously press the up and down dimmer buttons for '''1''' second.
 
#*The LED will flash Blue while connecting
 
#*The LED with flash Green when connected.
 
#*If the LED is flashing Red, the connection has failed.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Simultaniouly press the up and down dimmer buttons for '''10''' seconds.
 
 
 
<hr />
 
 
 
=='''<big>SmartThings</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3300-S</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
#The LED will flash Red and Green while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the recessed connect button for '''5''' seconds.
 
#Release the button when the LED starts flashing Red.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartSense Multi Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>STSS-MULT-001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the '''Connect''' button for '''6''' seconds, or until the LED light turns off.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Make sure the Outlet is within '''15''' feet ('''4.5''' meters) of the hub during setup.
 
#Hold the '''Connect''' button for '''6''' seconds, or until the LED light turns off.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the '''Connect''' button for '''6''' seconds, or until the LED light turns off.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi Sensor (2015 Model)</big>'''</div>
 
|<div style="text-align: center;">'''<big>F-SS-MULT-001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi Sensor (2016 Model)</big>'''</div>
 
|<div style="text-align: center;">'''<big>F-MLT-US-2</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover and hold the '''Connect''' button for '''5 seconds.'''
 
#Release it when the LED starts flashing Red.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release it when the LED starts flashing Red.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release it when the LED starts flashing Red.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multi Sensor v4</big>'''</div>
 
|<div style="text-align: center;">'''<big>STS-MLT-250</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Humidity Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>3310-S</big>'''</div>
 
|<div style="text-align: center;">'''<big>Humidity Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove the cover, and then the battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Slide the sensor off the mount, remove the cover, and then the battery.
 
#While holding down the reset button, reinsert battery
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove the cover, and then the battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartSense Moisture Sensor</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover of the Moisture Sensor.
 
#Remove the CR2 battery by pulling the ribbon.
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Moisture Sensor.
 
#Remove the CR2 battery by pulling the ribbon.
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover of the Moisture Sensor.
 
#Remove the CR2 battery by pulling the ribbon.
 
#Hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Leak Sensor v4 (2015)</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover of the Water Leak Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Water Leak Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover of the Water Leak Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartSense Motion Sensor</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold the Connect button for '''6''' seconds or until the LED light turns off.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold the Connect button for '''6''' seconds or until the LED light turns off.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold the Connect button for '''6''' seconds or until the LED light turns off.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor v2 (2014)</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor v3 (2015)</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
#The LED will flash Blue while attempting to connect.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover of the Motion Sensor.
 
#Remove the battery, then hold the '''Connect''' button while inserting the battery.
 
#Release the button once the LED is lit.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor v4 (2016)</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release it when the LED starts flashing Red.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release it when the LED starts flashing Red.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release it when the LED starts flashing Red.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>SmartSense Presence Sensor v2</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Presence Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Insert a small flathead screwdriver into the groove at the base of the SmartSense Presence Sensor
 
#Gently twist the screwdriver and the plastic case should pop open.
 
#Hold the '''Connect''' button on the sensor for about '''6''' seconds until the LED light turns off, and then release.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert a small flathead screwdriver into the groove at the base of the SmartSense Presence Sensor
 
#Gently twist the screwdriver and the plastic case should pop open.
 
#Hold the '''Connect''' button on the sensor for about '''6''' seconds until the LED light turns off, and then release.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Insert a small flathead screwdriver into the groove at the base of the SmartSense Presence Sensor
 
#Gently twist the screwdriver and the plastic case should pop open.
 
#Hold the '''Connect''' button on the sensor for about '''6''' seconds until the LED light turns off, and then release.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>SmartThings</big>'''</div>
 
|<div style="text-align: center;">'''<big>Arrival Sensor v4</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Presence Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release the button when the LED turns off.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release the button when the LED turns off.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the cover and hold the '''Connect''' button for '''5''' seconds.
 
#Release the button when the LED turns off.
 
 
 
<hr />
 
=='''<big>Sunricher</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sunricher</big>'''</div>
 
|<div style="text-align: center;">'''<big>AC Phase-Cut Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZG9101SAC-HP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Apply power to the device to start TouchLink Commissioning. You have '''180''' seconds before timeout. Repeat the operation if you exceed the timeout period.
 
#Bring the remote or touch panel within '''10''' cm of the device.
 
#Set the remote or touch panel into Touch Reset procedure to reset the device, please refer to the corresponding remote or touch panel manual to learn how.
 
#There will be an indication on the remote and a connected light will flash '''3''' times to indicate a successful reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Apply power to the device to set it into network pairing mode.
 
#A connected light will flash twice slowly. You have '''15''' seconds before timeout. Repeat the operation if you exceed the timeout period.
 
#A connected light will flash '''5''' times and then stay ON solid.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Perform a factory reset using the above proceedure.
 
 
 
<hr />
 
=='''<big>Sylvania</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ Contact and Temp Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>74388</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Slide the sensor off the mount, remove cover, and remove battery.
 
#While holding down the reset button, reinsert battery to factory reset the device.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ Motion and Temp Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>72923</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Hold down the '''Pairing/Reset''' button for more than '''10''' seconds.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Hold down the '''Pairing/Reset''' button for more than '''10''' seconds.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold down the '''Pairing/Reset''' button for more than '''10''' seconds.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>73743</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press and hold both the top and bottom button for '''3''' seconds
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press and hold both the top and bottom button for '''3''' seconds
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press and hold both the top and bottom button for '''3''' seconds
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ 4 Button Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>74099</big>'''</div>
 
|<div style="text-align: center;">'''<big>Button Controller</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Hold buttons '''1''' and '''4''' together. The LED will flash Red.
 
#Keep holding buttons '''1''' and '''4''' until the LED on the device stops flashing.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Hold buttons '''2''' and '''3''' until the LED on the device starts flashing Yellow.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Hold buttons '''1''' and '''4''' together. The LED will flash Red.
 
#Keep holding buttons '''1''' and '''4''' until the LED on the device stops flashing.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>72922</big>'''</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Make sure the plug is powered on. The light will be orange.
 
#Press the button located on the front of the plug and hold it down for '''10''' seconds.
 
#The light will flash orange when it has been reset.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Make sure the plug is powered on. The light will be orange.
 
#Press the button located on the front of the plug and hold it down for '''10''' seconds.
 
#The light will flash orange when it has been reset and is ready to be paired.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Make sure the plug is powered on. The light will be orange.
 
#Press the button located on the front of the plug and hold it down for '''10''' seconds.
 
#The light will flash orange when it has been reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sylvania</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart bulbs</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Turn the light off.
 
#Turn the light on for '''3''' seconds.
 
#Turn the light off.
 
#Repeat this cycle '''5''' times.
 
#Wait '''10''' seconds for the light to flash '''3''' times.
 
#Repeat these steps if the light does not flash '''3''' times.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Turn the light off.
 
#Turn the light on for '''3''' seconds.
 
#Turn the light off.
 
#Repeat this cycle '''5''' times.
 
#Wait '''10''' seconds for the light to flash '''3''' times.
 
#Repeat these steps if the light does not flash '''3''' times.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Turn the light off.
 
#Turn the light on for '''3''' seconds.
 
#Turn the light off.
 
#Repeat this cycle '''5''' times.
 
#Wait '''10''' seconds for the light to flash '''3''' times.
 
#Repeat these steps if the light does not flash '''3''' times.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Sylvania</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart+ BR30 bulb</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>74988</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Start with the Sylvania bulb in the ON position.
 
#Turn the bulb OFF and ON '''8''' times in a row, pausing for '''1''' second each time you turn the bulb ON or OFF.
 
#After the eighth time OFF, turn ON the bulb and leave it ON.
 
#Wait about '''5''' seconds.
 
#The BR30 bulb will flash if successfully reset.
 
#Repeat these steps if the light does not flash.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Start with the Sylvania bulb in the ON position.
 
#Turn the bulb OFF and ON '''8''' times in a row, pausing for '''1''' second each time you turn the bulb ON or OFF.
 
#After the eighth time OFF, turn ON the bulb and leave it ON.
 
#Wait about '''5''' seconds.
 
#The BR30 bulb will flash if it entered pairing mode successfully.
 
#Repeat these steps if the light does not flash.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#Start with the Sylvania bulb in the ON position.
 
#Turn the bulb OFF and ON '''8''' times in a row, pausing for '''1''' second each time you turn the bulb ON or OFF.
 
#After the eighth time OFF, turn ON the bulb and leave it ON.
 
#Wait about '''5''' seconds..
 
#The BR30 bulb will flash if successfully reset.
 
#Repeat these steps if the light does not flash.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Sylvania'''</big></div>
 
|<div style="text-align: center;">'''<big>Smart+ Flex RGBW</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat '''5''' times - Unplug for '''1''' second and then plug in for '''1''' second.
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in.
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset and ready for pairing.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat '''5''' times - Unplug for '''1''' second and then plug in for '''1''' second.
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in.
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset and ready for pairing.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Start with the Light Strip powered '''ON'''.
 
#Repeat 5 times - Unplug for '''1''' second and then plug in for '''1''' second.
 
#On the '''fifth''' time plugging in the Light Strip, leave it plugged in.
 
#After about '''3''' seconds, the Light Strip will flash rapidly '''3''' times to show a successful reset.
 
 
 
<hr />
 
=='''<big>Telguard</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Telguard'''</big></div>
 
|<div style="text-align: center;">'''<big>Garage Door Control Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>GDC1</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug in the GDC1.
 
#Remove the cover of the enclosure.
 
#Press the Z-Wave button once to reset the device.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the '''Z-Wave button''' once to join the GDC1 for your Z-Wave network.
 
#If the device fails to join the Z-Wave network, unplug it for '''10''' seconds.
 
#Repeat step 1 and again press the Z-Wave button.
 
#Replace the cover of the enclosure.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#Plug in the GDC1.
 
#Remove the cover of the enclosure.
 
#From the device's details page, select '''Remove Device''', then '''Remove'''.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave button once to exclude the GDC1 from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>Telldus</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Telldus'''</big></div>
 
|<div style="text-align: center;">'''<big>Plug-in ON/OFF switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>TZWP-100</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug in the device.
 
#Press and hold the button until the LED starts flashing white after approximately '''6''' seconds.
 
#Short-press the button once more.
 
#The device will now reset to factory defaults and the LED will flash red, indicating that it’s no longer part of the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug in the dimmer module.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the button '''3''' times within '''1.5''' seconds to enter inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#Plug in the dimmer module.
 
#From the device's details page, select '''Remove Device''', then '''Remove'''.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the button '''3''' times within '''1.5''' seconds to enter exclusion mode.
 
 
 
<hr />
 
=='''<big>Third Reality</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''Third Reality'''</big></div>
 
|<div style="text-align: center;">'''<big>Reality Switch</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Press the button on the front of the device for approximately '''30''' seconds.
 
#The LED will light steady for several seconds, then it will begin to flash rapidly
 
#The device has been reset and is ready for pairing.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Start with the Light Strip powered '''ON'''.
 
#Press the button on the front of the device for approximately '''30''' seconds.
 
#The LED will light steady for several seconds, then it will begin to flash rapidly
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Press the button on the front of the device for approximately '''30''' seconds.
 
#The LED will light steady for several seconds, then it will begin to flash rapidly
 
#The device has been reset and is ready for pairing.
 
 
 
<hr />
 
=='''<big>TKB</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;"><big>'''TKB'''</big></div>
 
|<div style="text-align: center;">'''<big>TKB Dimmer Socket</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>TZ67</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug in the dimmer module.
 
#Press the '''ON/OFF''' button '''3''' times within '''1.5''' seconds to enter inclusion mode.
 
#Within '''3''' seconds, press andhold the '''ON/OFF''' button for '''5''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug in the dimmer module.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the '''ON/OFF''' button '''3''' times within '''1.5''' seconds to enter inclusion mode.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#Plug in the dimmer module.
 
#From the device's details page, select '''Remove Device''', then '''Remove'''.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the '''ON/OFF''' button '''3''' times within '''1.5''' seconds to enter exclusion mode.
 
 
 
<hr />
 
=='''<big>Utilitech</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Utilitech</big>'''</div>
 
|<div style="text-align: center;">'''<big>Indoor Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>TSE07</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the battery cover.
 
#Press the pairing button in between the batteries '''8''' times, '''1''' second apart.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Remove the battery cover.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the paring button once.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#Remove the battery cover
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the paring button once.
 
 
 
<hr />
 
=='''<big>Vision</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Vision</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren & Strobe</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZM1601US-3</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn flash indicating the device is reset to factory defaults and excluded from the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#The distance between the siren and the hub is suggested to be in '''1''' meter ( '''3''' feet ) or less.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn off after inclusion.
 
#If the device is not included, it will continue in auto include more, attempting every '''4-6''' seconds for up to '''4''' attempts.
 
#The LED light will flash again if the siren has not been included.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn flash upon successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Vision</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren & Strobe</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZM1601US-5</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn flash indicating the device is reset to factory defaults and excluded from the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#The distance between the siren and the hub is suggested to be in '''1''' meter ( '''3''' feet ) or less.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn off after inclusion.
 
#If the device is not included, it will continue in auto include more, attempting every '''4-6''' seconds for up to '''4''' attempts.
 
#The LED light will flash again if the siren has not been included.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the mounting bracket and press the program button for at least '''1''' second & release.
 
#The LED light will turn flash upon successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Vision</big>'''</div>
 
|<div style="text-align: center;">'''<big>Shock Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZS5101</big>'''</div>
 
|<div style="text-align: center;">'''<big>Acceleration Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Push the Tamper switch while inserting the battery & holding the Tamper switch for 5 seconds
 
#The device will reset to the factory defaults and the LED will will remain ON solid
 
#Remove the battery and re-inset it to complete the reset process.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program button for at least '''1''' second & release.
 
#The LED light will turn off after inclusion.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the program button for at least '''1''' second & release.
 
#The LED light will turn off after exclusion.
 
 
 
<hr />
 
 
 
=='''<big>Visonic</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Visonic</big>'''</div>
 
|<div style="text-align: center;">'''<big>Door/Window Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>MCT-340</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the battery cover.
 
#Press and hold down the sensor’s tamper switch.
 
#Insert the battery into the sensor while observing battery polarity.
 
#Release the tamper switch within '''4''' seconds.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the battery cover.
 
#Press and release the tamper switch for '''1-2''' seconds.
 
#The LED will flash '''3''' times, every '''5''' seconds, repeating this cycle up to '''20''' times until paired.
 
#Test if the the sensor paired properly by moving the magnet away and toward it, observing the Hubitat Elevation™ device details status.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove the battery cover.
 
#Press and hold down the sensor’s tamper switch.
 
#Insert the battery into the sensor while observing battery polarity.
 
#Release the tamper switch within '''4''' seconds.
 
 
 
<hr />
 
=='''<big>WaterCop</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>WaterCop</big>'''</div>
 
|<div style="text-align: center;">'''<big>Emergency Water Shut-Off</big>'''</div>
 
|<div style="text-align: center;">'''<big>WAT171021</big>'''</div>
 
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the Mode button once.
 
#The status light will start flashing periodically ('''3-4''' times) indicating the device has been reset and excluded from the Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Ensure that the status light is flashing periodically ('''3-4''' times).
 
#Press the Mode button once.
 
#The status light will stop flashing upon inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Mode button once.
 
#The status light will start flashing periodically ('''3-4''' times) indicating the device has been excluded from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>Wireless</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Wireless</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smoke Detector</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWN-SD</big>'''</div>
 
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Briefly press the program button on the back of the device.
 
#The status LED will light up and then imeadiatly turn off.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Briefly press the program button on the back of the device.
 
#The status LED will light up for '''5''' seconds and then turn off upon successful inclusion to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Briefly press the program button on the back of the device.
 
#The status LED will light up and then imeadiatly turn off upon successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
 
 
=='''<big>Xfinity</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Xfinity</big>'''</div>
 
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>3400-X</big>'''</div>
 
|<div style="text-align: center;">'''<big>Keypad</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove batteries from keypad.
 
#Press and hold the wall tamper switch while reinstalling the batteries.
 
#Once the keypad illuminates, release the wall tamper switch.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Perform a factory reset.
 
#Remove and reinstall the batteries to being device pairing
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Remove batteries from keypad.
 
#Press and hold the wall tamper switch while reinstalling the batteries.
 
#Once the keypad illuminates, release the wall tamper switch.
 
 
 
<hr />
 
=='''<big>Yale</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Yale</big>'''</div>
 
|<div style="text-align: center;">'''<big>Yale Zigbee Locks</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the battery cover and batteries.
 
#Remove the interior escutcheon to access the reset button.
 
#The reset button is located beside the PCB cable connector.
 
#While pressing the reset button for a minimum of '''3''' seconds, reinstall the batteries.
 
#Release reset button and replace battery cover.  '''NOTE:''' ''Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.''
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Enter the master pin code and then press the button with the '''Gear''' icon on it.
 
#Press '''7''' on the keypad to enter network setup mode.
 
#Press '''1''' to join the Zigbee network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Enter the master pin code and then press the button with the '''Gear''' icon on it.
 
#Press '''7''' on the keypad to enter network setup mode.
 
#Press '''3''' to leave the Zigbee network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Yale</big>'''</div>
 
|<div style="text-align: center;">'''<big>Yale Z-Wave Locks</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Remove the battery cover and batteries.
 
#Remove the interior escutcheon to access the reset button.
 
#The reset button is located beside the PCB cable connector.
 
#While pressing the reset button for a minimum of '''3''' seconds, reinstall the batteries.
 
#Release reset button and replace battery cover.  '''NOTE:''' ''Upon reset, Master PIN Code creation is the only option available and must be performed prior to any other programming of the lock.''
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the master pin code and then press the button with the '''Gear''' icon on it.
 
#Press '''7''' on the keypad to enter network setup mode.
 
#Press '''1''' to include the lock in the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Enter the master pin code and then press the button with the '''Gear''' icon on it.
 
#Press '''7''' on the keypad to enter network setup mode.
 
#Press '''3''' to exclude the lock from the Z-Wave network.
 
 
 
<hr />
 
=='''<big>Yeelight</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Yeelight</big>'''</div>
 
|<div style="text-align: center;">'''<big>Yeelight Mono / CT bulbs</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>LAN</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Switch the bulb on and off '''5''' times in a row ('''2''' seconds '''ON''' and '''2''' seconds '''OFF''').
 
#The bulb will start pulsing slowly up and down.
 
#After '''5''' seconds, it will restart automatically, which means the bulb has been reset to factory defaults.
 
 
 
'''Join the LAN'''
 
 
 
#From the Hubitat Web Interface home page, select '''Apps.'''
 
#Choose '''Yeelight Integration''' from the list of Hubitat Elevation™ Built-In Apps
 
#*See [[Apps]] documentation for more detail.
 
#Using the Yeelight mobile app'','' enable '''LAN Control''' for each Yeelight prior to starting discovery. The '''LAN Control''' option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
 
#Open the Yeelight setup and start bulb discovery.
 
 
 
'''Leaving the LAN'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Switch the bulb on and off '''5''' times in a row ('''2''' seconds '''ON''' and '''2''' seconds '''OFF''').
 
#The bulb will start pulsing slowly up and down.
 
#After '''5''' seconds, it will restart automatically, which means the bulb has been reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Yeelight</big>'''</div>
 
|<div style="text-align: center;">'''<big>Yeelight Color bulbs</big>'''</div>
 
|<div style="text-align: center;"></div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>LAN</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Switch the bulb on and off '''5''' times in a row ('''2''' seconds '''ON''' and '''2''' seconds '''OFF''').
 
#The bulb will start flashing
 
#After '''5''' seconds, it will turn white, which means the bulb has been reset to factory defaults.
 
 
 
'''Join the LAN'''
 
 
 
#From the Hubitat Web Interface home page, select '''Apps.'''
 
#Choose '''Yeelight Integration''' from the list of Hubitat Elevation™ Built-In Apps
 
#*See [[Apps]] documentation for more detail.
 
#Using the Yeelight mobile app'','' enable '''LAN Control''' for each Yeelight prior to starting discovery. The '''LAN Control''' option can be enabled by selecting the lower right icon in the mobile app menu for each bulb.
 
#Open the Yeelight setup and start bulb discovery.
 
 
 
'''Leaving the LAN'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Switch the bulb on and off '''5''' times in a row ('''2''' seconds '''ON''' and '''2''' seconds '''OFF''').
 
#The bulb will start flashing
 
#After '''5''' seconds, it will turn white, which means the bulb has been reset to factory defaults.
 
 
 
<hr />
 
=='''<big>Zen</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zen</big>'''</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN-01</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Thermostat</big>'''</div>
 
|<div style="text-align: center;">'''<big>Zigbee</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#To do a full factory reset, which will delete all your configuration settings and your network connectivity, you need to remove the device from the wall and press the '''CONFIG''' button '''20''' times.
 
#*'''NOTE''': Performing a Factory Reset will reset your ZEN's HVAC-system configuration and all of your preferences and advanced settings changes. If you do a Factory Reset, make sure that you set your configuration code and preferences back to their correct values before replacing the display on the wall.
 
 
 
'''Join the Zigbee Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Pull the ZEN display off the wall and press the '''Network''' button on the rear of the display '''5''' times.
 
#You should see the network icon flashing on the front of the display indicating that your ZEN thermostat is attempting to connect to a network.
 
#The thermostat will indicate it is connected to Hubitat Elevation™ by a Network icon on the front of the device.
 
#If the network icon is flashing, the ZEN is trying to find your network. The network icon will be solid when you are connected to your Zigbee network.
 
 
 
'''Leaving the Zigbee Network'''
 
 
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#Pull the ZEN display off the wall and press the '''Network''' button on the rear of the display '''10''' times.
 
#The Network icon will turn OFF when the thermostat disconnects from the Zigbee network.
 
 
 
<hr />
 
 
 
=='''<big>Zipato</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zipato</big>'''</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>PH-PSE02</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Lock</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press tamper key '''4''' times within '''1.5''' seconds, but do not release the tamper key in the 4th press.
 
#The LED will stay ON solid for '''3''' seconds and then will turn OFF.
 
#Within '''2''' seconds of the LED turning OFF, release the tamper key. If successful, the LED will turn ON for '''1''' second.
 
#If reset fails, the LED will flash once.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the tamper key '''3''' times within '''1.5''' seconds to enter inclusion mode.
 
#After successful inclusion, the LED will light up for '''1''' second.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the tamper key '''3''' times within '''1.5''' seconds to enter exclusion mode.
 
 
 
<hr />
 
 
 
=='''<big>ZLINK</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>ZLINK</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZL-WD-100</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn on the connected lighting with the rocker.
 
#Quickly tap on the '''top''' of the rocker '''3''' times.
 
#Now quickly tap on the '''bottom''' of the rocker '''3''' times.
 
#When reset is successful, the light will turn off and on again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to include the device in the Z-Wave network.
 
#If inclusion fails, perform a factory reset, then try to include the device in the Z-Wave network again.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to exclude the device from the Z-Wave network.
 
#If exclusion fails, perform a factory reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>ZLINK</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZL-WS-100</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn on the connected lighting with the rocker.
 
#Quickly tap on the '''top''' of the rocker '''3''' times.
 
#Now quickly tap on the '''bottom''' of the rocker '''3''' times.
 
#When reset is successful, the light will turn off and on again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to include the device in the Z-Wave network.
 
#If inclusion fails, perform a factory reset, then try to include the device in the Z-Wave network again.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to exclude the device from the Z-Wave network.
 
#If exclusion fails, perform a factory reset.
 
 
 
<hr />
 
=='''<big>Zooz</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Plug</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN06</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug the smart plug into a grounded receptacle.
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''20''' seconds.
 
#The LED indicator will stay solid '''yellow''' for '''2''' seconds to indicate successful reset and the plug will then automatically turn off.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug the smart plug into a grounded receptacle located within '''3''' feet from your Z-Wave radio.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the Z-Wave button '''3''' times quickly.
 
#The LED indicator will flash '''blue'''.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the Z-Wave button '''3''' times quickly to exclude it from the Z-Wave network.
 
#LED indicator will flash orange.
 
#The LED indicator will remain solid '''orange''' for a few seconds to indicate successful exclusion from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Power Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN15</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug the power switch into a grounded receptacle.
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''20''' seconds.
 
#The LED indicator will flash '''orange''' and then stay solid '''orange''' for '''2''' seconds to indicate successful reset and the switch will then automatically turn off.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug the smart plug into a grounded receptacle located within '''3''' feet from your Z-Wave radio.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the Z-Wave button '''3''' times quickly.
 
#The LED indicator will start flashing '''blue''', then turn '''blue''' (on) or '''pink''' (off) once included to the Z-Wave network.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the Z-Wave button '''3''' times quickly to exclude it from the Z-Wave network.
 
#LED indicator will flash '''orange'''.
 
#The LED indicator will start flashing '''blue''', then turn '''blue''' (on) or '''pink''' (off) once excluded from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Power Strip Ver 2.0</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN20</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Power Strip</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Plug the Power Strip into a grounded receptacle.
 
#Tap the '''CH1''' button '''3''' times and hold on the third tap for at least '''10''' seconds.
 
#All LED indicators will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Plug the Power Strip into a grounded receptacle you’re planning to use it at (it doesn’t need to be close to the hub).
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the '''CH1''' button '''3''' times quickly.
 
#All LED indicators will start flashing.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the '''CH1''' button '''3''' times quickly.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN21</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
'''Factory Reset'''
 
 
 
#Tap the upper paddle '''3''' times and hold on the third tap for at least '''10''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the top paddle '''3''' times quickly.
 
#The LED indicator will flash to signal communication.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the bottom paddle '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN22</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the upper paddle '''3''' times and hold on the third tap for at least '''10''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the top paddle '''3''' times quickly.
 
#The LED indicator will flash to signal communication.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the bottom paddle '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>ON/OFF Toggle Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN23</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Toggle the switch '''down''' '''3''' times and hold on the third toggle for at least '''10''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch '''up''' '''3''' times quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch '''down''' '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer Toggle Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN24</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Toggle the switch '''down''' '''3''' times and hold on the third toggle for at least '''10''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch '''up''' '''3''' times quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Toggle the switch '''down''' '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Double Plug</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN25</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Outlet</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the Z-Wave button '''3''' times and hold on the third press for at least '''10''' seconds.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave button '''3''' times quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave button '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>S2 ON/OFF Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN26</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the upper paddle '''3''' times and hold on the third tap for at least '''10''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the top paddle '''3''' times quickly.
 
#The LED indicator will flash and will remain ON for '''2''' seconds to indicate successful communication.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the bottom paddle '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>S2 Dimmer Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZEN27</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Tap the upper paddle '''3''' times and hold on the third tap for at least '''10''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the top paddle '''3''' times quickly.
 
#The LED indicator will flash and will remain ON for '''2''' seconds to indicate successful communication.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Tap the bottom paddle '''3''' times quickly to exclude it from the Z-Wave network.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE02</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Please press the Z-Wave button '''6''' TIMES quickly ('''3''' unlock-lock cycles).
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Bring the motion sensor within direct reach of your Z-Wave radio.
 
#Quickly press the Z-Wave button on the motion sensor '''2''' times (unlock and then lock).
 
#Make sure the button is pushed in (locked) when you finish the process to re-enable motion detection.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press the Z-Wave button on the motion sensor '''2''' times (unlock and then lock).
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion and Light Mini Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE09</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''10''' seconds.
 
#The LED indicator flashes '''1''' time and it may then flash '''5''' times to indicate the device is no longer part of Z-Wave network.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Mini Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Mini Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE18</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''20''' seconds.
 
#The LED indicator will turn on then turn on solid and will then automatically turn off.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the '''4-5''' times.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the '''3''' times.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Multisiren</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE19</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the Z-Wave button '''4''' times and hold on the fourth press for at least '''5''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button '''4-5''' times.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button '''3''' times.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>S2 Outdoor Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE29</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Press the tamper switch '''4''' times and hold on the fourth press for at least '''5''' seconds.
 
#The LED indicator will flash to confirm successful reset.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the tamper switch '''4-5''' times.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the tamper switch '''3''' times.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE30</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Water Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''10''' seconds until the LED indicator flashes '''1''' time.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Water Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Water Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Smart Chime</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE33</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#'''PRESS AND HOLD''' the Z-Wave button for at least '''10''' seconds until the LED indicator flashes '''1''' time.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Water Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button on the Water Sensor '''3''' times.
 
#The LED indicator will flash quickly.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>4 in 1 Sensor</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZSE40</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#OPEN the back cover to trigger tamper switch.
 
#Press and release the Z-Wave button using a paperclip '''10''' times quickly (within '''10''' seconds).
 
#The sensor will start flashing immediately and will again flash '''5''' times after the '''10''' clicks (color depends on room temperature, it’s usually blue or yellow).
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button '''2''' times with a paperclip.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press and release the Z-Wave button '''2''' times with a paperclip.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>Zooz</big>'''</div>
 
|<div style="text-align: center;">'''<big>Water Valve</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZAC03</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Valve</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#'''PRESS AND HOLD''' the '''RED''' power button for at least 1'''0''' seconds until the LED indicator flashes '''1''' time.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#Connect the valve to power.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press the '''RED''' power button on the valve control '''3''' times.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Quickly press the '''RED''' power button on the valve control '''3''' times.
 
 
 
<hr />
 
=='''<big>ZWP</big>'''==
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>ZWP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZWP WD-100</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Dimmer</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn on the connected lighting with the rocker.
 
#Quickly tap on the '''top''' of the rocker '''3''' times.
 
#Now quickly tap on the '''bottom''' of the rocker '''3''' times.
 
#When reset is successful, the light will turn off and on again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to include the device in the Z-Wave network.
 
#If inclusion fails, perform a factory reset, then try to include the device in the Z-Wave network again.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to exclude the device from the Z-Wave network.
 
#If exclusion fails, perform a factory reset.
 
 
 
<hr />
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Device</div>
 
|<div style="text-align: center;">Product Number</div>
 
|<div style="text-align: center;">Device Type</div>
 
|<div style="text-align: center;">Protocol</div>
 
|-
 
|<div style="text-align: center;">'''<big>ZWP</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">
 
'''<big>ZWP WS-100</big>'''
 
</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
 
 
#Turn on the connected lighting with the rocker.
 
#Quickly tap on the '''top''' of the rocker '''3''' times.
 
#Now quickly tap on the '''bottom''' of the rocker '''3''' times.
 
#When reset is successful, the light will turn off and on again.
 
 
 
'''Join the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to include the device in the Z-Wave network.
 
#If inclusion fails, perform a factory reset, then try to include the device in the Z-Wave network again.
 
 
 
'''Exclusion from the Z-Wave Network'''
 
 
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the rocker switch once to exclude the device from the Z-Wave network.
 
#If exclusion fails, perform a factory reset.
 
 
 
<hr />'''*Note: Aeotec was formerly known as Aeon Labs.'''
 
__FORCETOC__
 

Latest revision as of 19:40, 25 September 2022

We're moving! Please visit http://docs2.hubitat.com for the latest documentation.

This information is now available in the new compatible device list (hover over the "Instructions" column) in: http://docs2.hubitat.com/devices/list-of-compatible-devices