Difference between revisions of "Join and Reset Instructions"

From Hubitat Documentation
Jump to: navigation, search
(Added Bosch Motion sensors)
(Added Aeon Doorbell 6 and Siren 6 - Corrections and readability improvements)
Line 18: Line 18:
  
 
#Remove the cover by rotating it counterclockwise
 
#Remove the cover by rotating it counterclockwise
#Press and hold the Connect button for 5 seconds
+
#Press and hold the Connect button for '''5''' seconds
 
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode.
 
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 27: Line 27:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the Connect button for 5 seconds
+
#Press and hold the Connect button for '''5''' seconds
 
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode
 
#After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode
  
Line 51: Line 51:
  
 
#Use the provided pin to press and hold the reset button for 10 seconds.
 
#Use the provided pin to press and hold the reset button for 10 seconds.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 57: Line 57:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 79: Line 79:
  
 
#Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
 
#Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 85: Line 85:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Hold down the off (circle) button for 10 seconds until it flashs green 3 times.
+
#Hold down the off (circle) button for '''10''' seconds until it flashes green '''3''' times.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 106: Line 106:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
#*Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.
+
#*Battery powered Zigbee devices often pair easier when their batteries are removed for '''10''' seconds following a factory reset.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 113: Line 113:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Use the provided pin to press and hold the reset button for 10 seconds.
+
#Use the provided pin to press and hold the reset button for '''10''' seconds.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 132: Line 132:
 
|<div style="text-align: center;">'''<big>ZW056</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW056</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing as a confirmation.
+
#Your Doorbell will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 143: Line 143:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
 
#Press the Action Button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
#If your Doorbell has been successfully linked to your network, its LED will become solid for 2 seconds, then stop. If linking was unsuccessful, the LED will flash when you tap its button.
+
#If your Doorbell has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop. If linking was unsuccessful, the LED will flash when you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 151: Line 151:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Doorbell.
 
#Press the Action Button on your Doorbell.
#If your Doorbell has been successfully unlinked to your network, its LED will begin to flash slowly indicating it is ready to be paired to a new network..
+
#If your Doorbell has been successfully unlinked to your network, its LED will begin to flash slowly indicating it is ready to be paired to a new network.
  
 
<hr />
 
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Doorbell 6</big>'''</div>
 +
|<div style="text-align: center;">'''<big>ZW162-A</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Doorbell</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
#Press and hold the Action button for '''20''' seconds
 +
# Within '''2-5''' seconds, the test doobell sound will run, then stop after '''5''' seconds has elapsed.
 +
# From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
 +
# After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 +
# With the LED pulsing, release the Action button, and the Doorbell 6 will be reset to factory defaults.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#Power Doorbell 6 through the provided power adapter.
 +
#Ensure that Doorbell 6 LED is flashing slowly.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Tap the Doorbell 6 Action Button once.
 +
#If Doorbell 6 has successfully paired to your Z-Wave gateway, the LED will be a solid color for '''30''' seconds, then turn off.
 +
#If is fails to join the Z-Wave network, the LED will flash slowly.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Action Button '''6''' times in '''2''' seconds.
 +
#If your Doorbell 6 has been successfully unpaired from the Z-Wave network, its LED will begin to flash slowly, indicating it is ready to join a Z-Wave network again.
 +
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 165: Line 203:
 
|<div style="text-align: center;">'''<big>ZW112</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW112</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
 
#Press and hold Door Window Sensor 6 Action button
 
#Press and hold Door Window Sensor 6 Action button
 
#Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
 
#Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
#If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
+
#If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 199: Line 237:
 
|<div style="text-align: center;">'''<big>ZW120</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW120</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
|}
  
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 218: Line 256:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast flash for 8 seconds and then slow flash for 3 seconds when you press the Action Button again.
+
#If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast flash for '''8''' seconds and then slow flash for '''3''' seconds when you press the Action Button again.
#If the removal was unsuccessful, the Status LED will fast flash for 2 seconds and then be solid for 2 seconds when you press the Action Button, repeat the above steps.
+
#If the removal was unsuccessful, the Status LED will fast flash for '''2''' seconds and then be solid for '''2''' seconds when you press the Action Button, repeat the above steps.
  
 
<hr />
 
<hr />
Line 236: Line 274:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 273: Line 311:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
 
#Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
#The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the will be flashing while awake.
+
#The sensor will now stay awake for '''10''' minutes to receive network instructions. The LED on the will be flashing while awake.
#*Note: The DSB04100 sensor can only be taught to communicate to devices within it’s own network.
+
#*Note: The DSB04100 sensor can only be taught to communicate to devices within its own network.
#*If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
+
#*If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for '''5''' seconds.
 
#*If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.
 
#*If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.
  
Line 297: Line 335:
 
|<div style="text-align: center;">'''<big>ZW062</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW062</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
 
|<div style="text-align: center;">'''<big>Garage Door Opener</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}
 
|}
  
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and release.
+
#Press and hold the Action Button for '''20''' seconds and release.
#Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing to confirm a success.
+
#Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for '''2''' seconds and then start slow flashing to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 310: Line 348:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#Press the Z-Wave Button on the Garage Door Controller.
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 second for a successful inclusion.
+
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 318: Line 356:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Z-Wave Button on the Garage Door Controller.
 
#Press the Z-Wave Button on the Garage Door Controller.
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 second for a successful exclusion.
+
#The LED on Garage Door Controller will flash rapidly, followed by a solid LED for '''1-2''' second for a successful exclusion.
 
#The Network LED on the Garage Door Controller should now be flashing slowly to indicate it is ready to be paired to a new network.
 
#The Network LED on the Garage Door Controller should now be flashing slowly to indicate it is ready to be paired to a new network.
  
Line 333: Line 371:
 
|<div style="text-align: center;">'''<big>ZW097</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW097</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.
+
#Press and hold the Action Button for '''20''' seconds and Status LED will be solid for '''2''' seconds to confirm a success.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 343: Line 381:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear. If linking was unsuccessful, the LED will continue to flash if you tap its button.
+
#If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds, then disappear.
 +
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 351: Line 390:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your Sensor.
 
#Press the Action Button on your Sensor.
#If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
+
#If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
 +
#If unlinking was not successful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.
  
 
<hr />
 
<hr />
Line 368: Line 408:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 10 seconds.
+
#Press and hold the Action Button for '''10''' seconds.
 
#If successful, the LED on the HEM should begin to flash slowly.
 
#If successful, the LED on the HEM should begin to flash slowly.
  
Line 376: Line 416:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for 1 second. If the linking was unsuccessful the light will flash after pressing your meter’s Action Button.
+
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for '''1''' second. If the linking was unsuccessful the light will flash after pressing your meter’s Action Button.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 384: Line 424:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button (small black button under the battery tray) on your reader.If your Reader has been successfully removed from your network its light will flash for 1 second. If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
+
#Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully removed from your network, its light will flash for '''1''' second.
 +
#If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.
  
 
----
 
----
Line 398: Line 439:
 
|<div style="text-align: center;">'''<big>ZW095</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW095</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
 
|<div style="text-align: center;">'''<big>Energy Meter</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 10 seconds.
+
#Press and hold the Action Button for '''10''' seconds.
 
#If successful, the LED on the HEM should begin to flash slowly.
 
#If successful, the LED on the HEM should begin to flash slowly.
  
Line 429: Line 470:
 
|<div style="text-align: center;">'''<big>ZW098</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW098</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
Line 438: Line 479:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch ON. LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
+
#With LED Bulb in its fitting, wait '''2''' seconds. Now toggle your wall switch ON. LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
 
#After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
 
#After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.
  
Line 447: Line 488:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Turn LED Bulb’s wall switch on.
 
#Turn LED Bulb’s wall switch on.
#Toggle LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if successful, the orange LED will be solid for 2 seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
+
#Toggle LED Bulb’s wall switch off, on, off, on, off, on within '''2''' seconds. The LED should flash orange, and if successful, the orange LED will be solid for '''2''' seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
#To confirm successful removal its color will change to orange for 2 seconds before changing to white. If removal was unsuccessful, LED Bulb will flash orange for 3 seconds before changing to red for 2 seconds.
+
#To confirm successful removal its color will change to orange for '''2''' seconds before changing to white. If removal was unsuccessful, LED Bulb will flash orange for '''3''' seconds before changing to red for '''2''' seconds.
  
 
----
 
----
Line 462: Line 503:
 
|<div style="text-align: center;">'''<big>ZWA002</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA002</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between 0.5 - 2 seconds per re-power.
+
#Toggle LED Bulb's wall switch '''6''' times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
#If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.
+
#If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white '''3''' times to indicate a successful factory reset.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 473: Line 514:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to 10 seconds.
+
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to '''10''' seconds.
#After successfully connecting to your network, LED Bulb will flash green -> white color for 3 seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.
+
#After successfully connecting to your network, LED Bulb will flash green -> white color for '''3''' seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for '''3''' seconds.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 481: Line 522:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between 0.5 - 2 seconds per cycle.
+
#Toggle LED Bulb’s wall switch '''3''' times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
#LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for 3 seconds.
+
#LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for '''3''' seconds.
  
 
----
 
----
Line 496: Line 537:
 
|<div style="text-align: center;">'''<big>ZWA001</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZWA001</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
 
|<div style="text-align: center;">'''<big>Bulb</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between 0.5 - 2 seconds per re-power.
+
#Toggle LED Bulb's wall switch 6 times ('''off -> on, off -> on, off -> on, off -> on, off -> on, off -> on''') between '''0.5 - 2''' seconds per re-power.
 
#If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
 
#If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.
  
Line 507: Line 548:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will flash 2x times to indicate that it is looking for a Z-Wave network to connect to.
+
#With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will flash '''2''' times to indicate that it is looking for a Z-Wave network to connect to.
#After successfully connecting to your network, LED Bulb will flash off then on in about half a second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
+
#After successfully connecting to your network, LED Bulb will flash off then on in about '''0.5''' second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 515: Line 556:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Turn LED Bulb’s wall switch on and wait 1 second.
+
#Turn LED Bulb’s wall switch on and wait '''1''' second.
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between 0.5 - 2 seconds per cycle.
+
#Toggle LED Bulb’s wall switch 3 times ('''off > on''', '''off > on''', '''off > on''') between '''0.5 - 2''' seconds per cycle.
#LED Bulb 6 if successful will flash once, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
+
#LED Bulb 6 if successful will flash once, dim to 5% for '''5''' seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.
  
 
----
 
----
Line 534: Line 575:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Hold the Z-Wave button for 30 seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for 30 seconds).
+
#Hold the Z-Wave button for '''30''' seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for '''30''' seconds).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 628: Line 669:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the button on the Micro Switch G2 for 20 seconds and then release it.
+
#Press and hold the button on the Micro Switch G2 for '''20''' seconds and then release it.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 642: Line 683:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
+
#If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch '''6''' times (ON to OFF or OFF to ON).
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
 
#If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but '''only if Micro is not already connected to an external switch'''.
  
Line 661: Line 702:
  
 
#Pull down the panel on the  Minimote
 
#Pull down the panel on the  Minimote
#Press and hold the bottom 2 buttons down. The Red and Blue LED will alternate faster and faster.
+
#Press and hold the bottom '''2''' buttons down. The Red and Blue LED will alternate faster and faster.
 
#When both Red and Blue LED become solid, you may let go.
 
#When both Red and Blue LED become solid, you may let go.
  
Line 691: Line 732:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold Multisensor Gen5 Action button (For 20 seconds)
+
#Press and hold Multisensor Gen5 Action button (For '''20''' seconds)
#The LED of the Multisensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
+
#The LED of the Multisensor Gen5 will flash faster and faster. At '''20''' seconds, the LED should become solid for '''1-2''' seconds to confirm factory reset.
 
#Release the Multisensor Gen5 Action Button.
 
#Release the Multisensor Gen5 Action Button.
  
Line 701: Line 742:
 
#Press the Z-Wave Button on your MultiSensor.
 
#Press the Z-Wave Button on your MultiSensor.
 
#You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
 
#You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
#If the LED flashs when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
+
#If the LED flashes when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 724: Line 765:
 
|<div style="text-align: center;">'''<big>ZW100</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW100</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Motion Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash.
+
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
  
Line 735: Line 776:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash Green rapidly, followed by a solid Green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
+
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash Green rapidly, followed by a solid Green LED for '''1''' second for a successful inclusion, or a solid red LED for '''1''' second for a failed inclusion.
 
#You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
 
#You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
#If the green LED flashs when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
+
#If the green LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 745: Line 786:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
 
#Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash.
+
#If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for '''3''' seconds. When you press the Action Button on MultiSensor, its green LED will flash.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
 
#If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.
  
Line 763: Line 804:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the NanoMote button for 20 seconds.
+
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#The LED will change from: Orange > Green > Red > Pink > Red
#Release the button on the second Red LED status. It will remain red for 2 seconds
+
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
#Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
+
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 773: Line 814:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Double click the NanoMote button, the LED will flash rapidly with a white color.
 
#Double click the NanoMote button, the LED will flash rapidly with a white color.
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
+
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
#If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
+
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
#*If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
+
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 800: Line 841:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the NanoMote button for 20 seconds.
+
#Press and hold the NanoMote button for '''20''' seconds.
 
#The LED will change from: Orange > Green > Red > Pink > Red
 
#The LED will change from: Orange > Green > Red > Pink > Red
#Release the button on the second Red LED status. It will remain red for 2 seconds
+
#Release the button on the second Red LED status. It will remain Red for '''2''' seconds
#Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).
+
#Tap button again while second Red LED is illuminated (you'll have '''2''' seconds to do so).
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 810: Line 851:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Double click the NanoMote button (can be any button), the LED will flash rapidly with a white color.
 
#Double click the NanoMote button (can be any button), the LED will flash rapidly with a white color.
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
+
#If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about '''10''' seconds, then flash green to indicate it is awake.
#*If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
+
#If the adding was unsuccessful and the red LED will be solid for '''2''' seconds and then off, repeat the above steps.
 +
#*If your NanoMote does not go to sleep on its own, press and hold for '''2''' seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 837: Line 879:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 846: Line 888:
 
#Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into pairing mode.
 
#Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into pairing mode.
 
#If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
 
#If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
#If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.
+
#If the pairing was unsuccessful, the red LED will be on for '''2''' seconds and then remain a colorful gradient, repeat the steps above.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 853: Line 895:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 871: Line 913:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 879: Line 921:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#Press the Action Button once on the Nano Switch.
#If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
+
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 886: Line 928:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 904: Line 946:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it.
+
#Press and hold the Action Button for '''20''' seconds and then release it.
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#Your Nano Switch will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 912: Line 954:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on the Nano Switch.
 
#Press the Action Button once on the Nano Switch.
#If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.
+
#If inclusion is successful, the green LED will be on for '''2''' seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for '''2''' seconds and then return to a colorful gradient.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 919: Line 961:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
+
#Press the Action Button on the Nano Switch once or toggle the external manual switch '''3''' times in fast succession.
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
 
#If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).
  
Line 989: Line 1,031:
 
|<div style="text-align: center;">'''<big>ZW117</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW117</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
 
|<div style="text-align: center;">'''<big>Repeater</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Z-Wave Button for 20 seconds to completely factory reset your Range Extender 6.
+
#Press and hold the Z-Wave Button for '''20''' seconds to completely factory reset your Range Extender 6.
#During the time that you are holding your Range Extender 6 action button down, the LED will flash through these colors: Yellow (at 2 seconds) > Purple (at 5 seconds) > Red for 8 seconds (initializing factory reset) > Green for 20 seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
+
#During the time that you are holding your Range Extender 6 action button down, the LED will flash through these colors: Yellow (at '''2''' seconds) > Purple (at '''5''' seconds) > Red for '''8''' seconds (initializing factory reset) > Green for '''20''' seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
#You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.
+
#You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for '''2''' seconds and then remain the colorful gradient status as a confirmation.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,001: Line 1,043:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will flash green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
 
#Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will flash green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
#If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for 2 seconds then turn off. If the adding was unsuccessful, the red LED will be on for 2 seconds and then remain colorful gradient status, repeat the steps above.
+
#If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for '''2''' seconds then turn off. If the adding was unsuccessful, the red LED will be on for '''2''' seconds and then remain colorful gradient status, repeat the steps above.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,024: Line 1,066:
 
|<div style="text-align: center;">'''<big>ZW089</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW089</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
 
|<div style="text-align: center;">'''<big>Contact Sensor</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds and then release it. Your sensor will now be reset to its original settings
+
#Press and hold the Action Button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,033: Line 1,075:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear.
+
#Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for '''2''' seconds then disappear.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
  
Line 1,059: Line 1,101:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button for 20 seconds
+
#Press and hold the Action button for '''20''' seconds
#At 8 seconds, the Siren will sound for 1 second, then stop
+
#At 8 seconds, the Siren will sound for '''1''' second, then stop
#The LED will continue to flash faster and faster and then will then turn solid for 2 seconds to indicate a successful factory reset
+
#The LED will continue to flash faster and faster and then will then turn solid for '''2''' seconds to indicate a successful factory reset
 
#You may let go of its Action button, and the Siren Gen5 factory reset is complete.
 
#You may let go of its Action button, and the Siren Gen5 factory reset is complete.
  
Line 1,069: Line 1,111:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Siren Gen5, and its LED will flash rapidly to indicate that it is communicating.
 
#Press the Action Button on your Siren Gen5, and its LED will flash rapidly to indicate that it is communicating.
#If your Siren has been successfully linked to your network, its LED will become solid for 2 seconds, then stop.
+
#If your Siren has been successfully linked to your network, its LED will become solid for '''2''' seconds, then stop.
 
#If linking was unsuccessful, the LED will flash when you tap its button.
 
#If linking was unsuccessful, the LED will flash when you tap its button.
  
Line 1,079: Line 1,121:
 
#Press the Action Button on your Siren.
 
#Press the Action Button on your Siren.
 
#If your Siren has been successfully unlinked from your network, its LED will begin to flash.
 
#If your Siren has been successfully unlinked from your network, its LED will begin to flash.
 +
 +
<hr />
 +
{| class="wikitable sortable"
 +
|<div style="text-align: center;">Brand</div>
 +
|<div style="text-align: center;">Device</div>
 +
|<div style="text-align: center;">Product Number</div>
 +
|<div style="text-align: center;">Device Type</div>
 +
|<div style="text-align: center;">Protocol</div>
 +
|-
 +
|<div style="text-align: center;">'''<big>Aeotec*</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Siren 6</big>'''</div>
 +
|<div style="text-align: center;">'''<big>ZW164-A</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Siren</big>'''</div>
 +
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 +
|}'''Factory Reset'''
 +
 +
# Press and hold the Action button for '''20''' seconds
 +
# Within '''2-5''' seconds, the test siren sound will run, then stop after '''5''' seconds has elapsed.
 +
# From '''5-10''' seconds, the LED will begin to flash faster and faster still from '''10-20''' seconds.
 +
# After '''21''' seconds, the LED will quickly flash '''3''' times, and then the LED slowly pulse up and down as you hold down the Action Button.
 +
# With the LED pulsing, release the Action button, and the Siren 6 will be reset to factory defaults.
 +
 +
'''Join the Z-Wave Network'''
 +
 +
#Power Siren 6 through the provided power adapter.
 +
#Ensure that Siren 6 LED is flashing slowly.
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 +
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 +
#Quickly tap the Siren 6 Action Button once.
 +
#If Siren 6 has successfully joined your Z-Wave network, the LED will emit a solid color for '''30''' seconds, then turn off.
 +
#If the Siren 6 failed to pair, the LED will continue to blink slowly.
 +
 +
'''Exclusion from the Z-Wave Network'''
 +
 +
#From the device's details page, select '''Remove Device''', then '''Remove'''
 +
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 +
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 +
#Press the Action Button '''6''' times within '''2''' seconds .
 +
#If your Siren 6 has been successfully excluded from the Z-Wave network, its LED will begin to flash slowly which indicates that it is ready to be paired again.
  
 
<hr />
 
<hr />
Line 1,093: Line 1,174:
 
|<div style="text-align: center;">'''<big>ZW096</big>'''</div>
 
|<div style="text-align: center;">'''<big>ZW096</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
 
|<div style="text-align: center;">'''<big>Switch</big>'''</div>
|<div style="text-align: center;">'''<big>Z-Wave</big>'''</div>
+
|<div style="text-align: center;">'''<big>Z-Wave Plus</big>'''</div>
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 20 seconds.
+
#Press and hold the Action Button for '''20''' seconds.
 
#The LED will change between these colors: Yellow > Purple > Red (flashs faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
 
#The LED will change between these colors: Yellow > Purple > Red (flashs faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
 
#When the LED changes to Green state, you may let go of the action button.
 
#When the LED changes to Green state, you may let go of the action button.
Line 1,106: Line 1,187:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your Switch once and the LED will flash a green LED.
 
#Press the Action Button on your Switch once and the LED will flash a green LED.
#If your switch has been successfully linked to your network, its LED will become solid green for 2 seconds.
+
#If your switch has been successfully linked to your network, its LED will become solid green for '''2''' seconds.
 
#If linking was unsuccessful, the LED will return to a rainbow gradient.
 
#If linking was unsuccessful, the LED will return to a rainbow gradient.
  
Line 1,134: Line 1,215:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action Button for 15 seconds.
+
#Press and hold the Action Button for '''15''' seconds.
 
#The red LED flashes to confirm a successful factory reset.
 
#The red LED flashes to confirm a successful factory reset.
  
Line 1,142: Line 1,223:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button on your sensor once.
 
#Press the Action Button on your sensor once.
#The LED will turn yellow LED for 10 seconds.
+
#The LED will turn yellow LED for '''10''' seconds.
 
#If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
 
#If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.
  
Line 1,151: Line 1,232:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your sensor.
 
#Press the Action Button on your sensor.
#The LED will turn purple for 2 seconds, and then white when exclusion is successful.
+
#The LED will turn purple for '''2''' seconds, and then white when exclusion is successful.
  
 
<hr />
 
<hr />
Line 1,169: Line 1,250:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button (20 seconds).
+
#Press and hold the Action button for '''20''' seconds.
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
+
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
#Let go of the Action Button.
  
Line 1,178: Line 1,259:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#Press the Action Button once on WallMote Quad to include it.
#The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
+
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,186: Line 1,267:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#Press the Action Button on your WallMote Quad.
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
+
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 +
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
  
 
<hr />
 
<hr />
Line 1,203: Line 1,285:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the Action button (20 seconds).
+
#Press and hold the Action button for '''20''' seconds.
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
+
#The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for '''2''' seconds to indicate a successful factory reset.
 
#Let go of the Action Button.
 
#Let go of the Action Button.
  
Line 1,212: Line 1,294:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the Action Button once on WallMote Quad to include it.
 
#Press the Action Button once on WallMote Quad to include it.
#The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
+
#The green LED will be on for '''2''' seconds and then the orange LED will fast flash for '''10''' minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,220: Line 1,302:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press the Action Button on your WallMote Quad.
 
#Press the Action Button on your WallMote Quad.
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.
+
#If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
 +
#If the removal was unsuccessful, the red LED will be solid for '''2''' seconds and then turn off, repeat the above steps.
  
 
<hr />
 
<hr />
Line 1,283: Line 1,366:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,289: Line 1,372:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,297: Line 1,380:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
Line 1,314: Line 1,397:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,320: Line 1,403:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,328: Line 1,411:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
Line 1,347: Line 1,430:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press the tamper switch for 6 times to restore factory settings.
+
#Press the tamper switch for '''6''' times to restore factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,353: Line 1,436:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
+
#Activate the inclusion mode at the sensor by pressing the tamper switch '''3''' times.
#Wait about 15-30 seconds while the sensor and hub finish the inclusion process.
+
#Wait about '''15-30''' seconds while the sensor and hub finish the inclusion process.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,361: Line 1,444:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.
+
#Press the tamper switch '''3''' times and the sensor will be removed from the Z-Wave network after '''15-30''' seconds.
  
 
<hr />
 
<hr />
Line 1,382: Line 1,465:
 
#Unlock the battery cover and slide it upwards to remove.
 
#Unlock the battery cover and slide it upwards to remove.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
#Wait at least 4 seconds, but do not release the tamper switch.
+
#Wait at least '''4''' seconds, but do not release the tamper switch.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Release the tamper switch. The device is now reset to factory default settings.
 
#Release the tamper switch. The device is now reset to factory default settings.
Line 1,391: Line 1,474:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#Remove both batteries for at least 10 seconds.
+
#Remove both batteries for at least '''10''' seconds.
#Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds
+
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off (5 for seconds)''' and will continue to blink in this cycle for up to 3 minutes
+
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
#If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
+
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 +
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>
Line 1,415: Line 1,499:
 
#Unlock the battery cover and slide it upwards to remove.
 
#Unlock the battery cover and slide it upwards to remove.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
 
#Press upward on the tamper switch located in-between the batteries, keeping it engaged while you '''remove both batteries'''.
#Wait at least 4 seconds, but do not release the tamper switch.
+
#Wait at least '''4''' seconds, but do not release the tamper switch.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Keep the tamper switch engaged while you reinsert both batteries.
 
#Release the tamper switch. The device is now reset to factory default settings.
 
#Release the tamper switch. The device is now reset to factory default settings.
Line 1,424: Line 1,508:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Pairing''' on the '''Device Discovery''' page.
 
#*See Discovering your devices for detail instructions.
 
#*See Discovering your devices for detail instructions.
#Remove both batteries for at least 10 seconds.
+
#Remove both batteries for at least '''10''' seconds.
#Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds
+
#Reinsert both batteries. The LED on the front of the sensor will be solid for '''2''' seconds
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off (5 for seconds)''' and will continue to blink in this cycle for up to 3 minutes
+
#The LED will begin to blink '''On''' > '''Off''' > '''On''' > '''Off''' > '''On''' > '''Off''' (for '''5''' seconds) and will continue to blink in this cycle for up to '''3''' minutes
#If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
+
#If the motion sensor does not pair with the hub in less than '''3''' minutes, perform a factory reset and repeat the above steps to join the Zigbee network.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''<hr />
 +
 
=='''<big>Centralite</big>'''==
 
=='''<big>Centralite</big>'''==
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
Line 1,512: Line 1,597:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,542: Line 1,627:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,572: Line 1,657:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,602: Line 1,687:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace
+
#Slide the sensor off the mount and remove cover. Remove battery for '''10''' seconds and replace
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
Line 1,657: Line 1,742:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
+
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
 
#The bulb will flash once, indicating it is reset and ready for pairing
 
#The bulb will flash once, indicating it is reset and ready for pairing
  
Line 1,665: Line 1,750:
  
 
#Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
 
#Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
#Hold the remote within 4 inches of the bulb.
+
#Hold the remote within '''4''' inches of the bulb.
#Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts flashing on and off.
+
#Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about '''10''' seconds, until the bulb starts flashing on and off.
 
#If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
 
#If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
 
#*''This method can be used for nearly ALL ZigBee LL bulbs.''
Line 1,672: Line 1,757:
 
*'''''Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)'''''
 
*'''''Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)'''''
  
#Hold the remote within 4 inches of the bulb.
+
#Hold the remote within '''4''' inches of the bulb.
 
#Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
 
#Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
 
#The bulb should flash on and off
 
#The bulb should flash on and off
Line 1,683: Line 1,768:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
+
#Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb > pause '''2''' seconds > turn OFF the bulb > pause '''2''' seconds > Turn ON the bulb
 
#The bulb will flash once, indicating it is reset and ready for pairing
 
#The bulb will flash once, indicating it is reset and ready for pairing
  
Line 1,713: Line 1,798:
  
 
#Open the Cover and make sure the Door/Window Sensor is powered.
 
#Open the Cover and make sure the Door/Window Sensor is powered.
#Hold the Connect Button for 10 seconds until the LED indicator flashs once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,720: Line 1,805:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Cover of the Door/Window Sensor.
 
#Remove the Cover of the Door/Window Sensor.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,728: Line 1,813:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the Cover of the Door/Window Sensor.
 
#Remove the Cover of the Door/Window Sensor.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,746: Line 1,831:
  
 
#Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
 
#Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
#Wait for 5 seconds.
+
#Wait for '''5''' seconds.
#Move the Magnet and Sensor Base in and out of the closed position 6 times.
+
#Move the Magnet and Sensor Base in and out of the closed position '''6''' times.
#The LED indicator will light up red for five seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
+
#The LED indicator will light up Red for '''5''' seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,755: Line 1,840:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Sensor Cover and the LED indicator will start flashing yellow.
 
#Remove the Sensor Cover and the LED indicator will start flashing yellow.
#Press the Button quickly 3 times in a row.
+
#Press the Button quickly '''3''' times in a row.
#The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green three times then flash red until the cover is replaced.
+
#The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green '''3''' times then flash red until the cover is replaced.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,764: Line 1,849:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the SENSOR COVER and the LED indicator will start flashing red.
 
#Remove the SENSOR COVER and the LED indicator will start flashing red.
#Press the Button quickly 3 times in a row.
+
#Press the Button quickly '''3''' times in a row.
#The LED Indicator will flash green three times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
+
#The LED Indicator will flash green '''3''' times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.
  
 
<hr />
 
<hr />
Line 1,783: Line 1,868:
  
 
#Open the Back Plate and make sure the Leak Sensor is powered.
 
#Open the Back Plate and make sure the Leak Sensor is powered.
#Hold the Connect Button for 10 seconds until the LED indicator flashs once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashs once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,790: Line 1,875:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Leak Sensor by twisting it apart.
 
#Remove the cover of the Leak Sensor by twisting it apart.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating inclusion.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,798: Line 1,883:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the cover of the Leak Sensor by twisting it apart.
 
#Remove the cover of the Leak Sensor by twisting it apart.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,816: Line 1,901:
  
 
#Remove the Cover and make sure the Motion Detector is powered.
 
#Remove the Cover and make sure the Motion Detector is powered.
#Hold the Connect Button for 10 seconds until the LED indicator flashs once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,823: Line 1,908:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the cover of the Motion Detector by twisting it apart.
 
#Remove the cover of the Motion Detector by twisting it apart.
#Press the Connect Button quickly 3 times in a row.
+
#Press the Connect Button quickly '''3''' times in a row.
#The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,832: Line 1,917:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
 
#Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,850: Line 1,935:
  
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
#Press and hold the CONNECT BUTTON for at least 10 seconds then release.
+
#Press and hold the CONNECT BUTTON for at least '''10''' seconds then release.
 
#A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
 
#A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.
  
Line 1,858: Line 1,943:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
#Press the CONNECT BUTTON quickly 3 times in a row.
+
#Press the CONNECT BUTTON quickly '''3''' times in a row.
#The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,867: Line 1,952:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
 
#Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
#Press the CONNECT BUTTON quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the CONNECT BUTTON quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,885: Line 1,970:
  
 
#Plug in the On/Off Plug-In Switch.
 
#Plug in the On/Off Plug-In Switch.
#Hold the Connect Button for 10 seconds until the LED Indicator flashs once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED Indicator flashes once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,891: Line 1,976:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful inclusion to the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,899: Line 1,984:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
 
#Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
#Press the Connect Button quickly 3 times in a row. The LED indicator will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED indicator will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,916: Line 2,001:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Hold the Button for 10 seconds until the LED flashs 10 times, then release the button
+
#Hold the Button for '''10''' seconds until the LED flashes '''10''' times, then release the button
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,923: Line 2,008:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash 5 times indicating successful inclusion.
+
#Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash '''5''' times indicating successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,930: Line 2,015:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Button quickly 3 times in a row The LED will flash 5 times indicating successful exclusion.
+
#Press the Button quickly '''3''' times in a row The LED will flash '''5''' times indicating successful exclusion.
  
 
<hr />
 
<hr />
Line 1,948: Line 2,033:
  
 
#Open the Back Plate and make sure the Siren is powered.
 
#Open the Back Plate and make sure the Siren is powered.
#Hold the Connect Button for 10 seconds until the LED Ring flashs once, then release the button.
+
#Hold the Connect Button for '''10''' seconds until the LED Ring flashs once, then release the button.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 1,955: Line 2,040:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Remove the Back Plate of the Siren.
 
#Remove the Back Plate of the Siren.
#Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful inclusion to the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful inclusion to the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,963: Line 2,048:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Remove the Back Plate of the Siren.
 
#Remove the Back Plate of the Siren.
#Press the Connect Button quickly 3 times in a row. The LED Ring will flash five times indicating successful exclusion from the Z-Wave network.
+
#Press the Connect Button quickly '''3''' times in a row. The LED Ring will flash '''5''' times indicating successful exclusion from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 1,980: Line 2,065:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the open/close button for at least 10 seconds then release.
+
#Press and hold the open/close button for at least '''10''' seconds then release.
 
#The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
 
#The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.
  
Line 1,987: Line 2,072:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly 3 times in a row. The LED will stop flashing and stay on continuously upon successful inclusion.
+
#Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly '''3''' times in a row. The LED will stop flashing and stay on continuously upon successful inclusion.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 1,994: Line 2,079:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.
+
#When prompted, press the “open/close” button on the Shut-Off quickly '''3''' times in a row.
  
 
<hr />
 
<hr />
Line 2,016: Line 2,101:
 
#Press and hold the button on the front of the PD-100
 
#Press and hold the button on the front of the PD-100
 
#Plug the PD-100 in while still pressing the button
 
#Plug the PD-100 in while still pressing the button
#After 3 seconds, release the button. If the button flashs, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
+
#After '''3''' seconds, release the button. If the button flashes, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,051: Line 2,136:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the device switch one time to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
+
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,058: Line 2,143:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the device switch one time to include it in the network. The LED will stop flashing, indicating the dimmer has been successfully included in the Z-Wave network.
+
#Press the device switch once to include it in the network. The LED will stop flashing, indicating the dimmer has been successfully included in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,065: Line 2,150:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the device switch one time to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
+
#Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 2,086: Line 2,171:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
  
Line 2,093: Line 2,178:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
#When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.
  
Line 2,101: Line 2,186:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
 
#When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.
  
Line 2,122: Line 2,207:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for 1 second, then reinstall it.
+
#Remove the battery for '''1''' second, then reinstall it.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,128: Line 2,213:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 10 seconds, then reinstall it.
+
#Remove the battery for at least '''10''' seconds, then reinstall it.
#If the LED starts flashing continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.
+
#If the LED starts flashing continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for '''10''' seconds if adding to a Z-Wave network fails.
#If after 5 seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
+
#If after '''5''' seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,137: Line 2,222:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the Flood Freeze case and remove the battery for 1 second.
+
#Open the Flood Freeze case and remove the battery for '''1''' second.
 
#Replace the battery and the device should be removed from the Z-Wave network.
 
#Replace the battery and the device should be removed from the Z-Wave network.
  
Line 2,158: Line 2,243:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
#Re-attach the battery cover
  
Line 2,165: Line 2,250:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#Re-attach the battery cover and the device with enter inclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
 
#Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.
  
Line 2,175: Line 2,260:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#Re-attach the battery cover and the device with enter exclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
Line 2,233: Line 2,318:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
  
Line 2,240: Line 2,325:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If the LED starts flashing continually, the sensor has not been added. Repeat the steps.
 
#If the LED starts flashing continually, the sensor has not been added. Repeat the steps.
  
Line 2,248: Line 2,333:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Open the FireFighter case and press the learn button on the device for one second.
+
#Open the FireFighter case and press the learn button on the device for '''1''' second.
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
 
#If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously
  
Line 2,276: Line 2,361:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Press the inclusion / exclusion button on the Smart Switch.
 
#Press the inclusion / exclusion button on the Smart Switch.
#The LED on the front of the unit will turn off if successful included in the network.
+
#The LED on the front of the unit will turn off if successfully included in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,371: Line 2,456:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
#Re-attach the battery cover
  
Line 2,378: Line 2,463:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#Re-attach the battery cover and the device with enter inclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
  
Line 2,388: Line 2,473:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#Re-attach the battery cover and the device with enter exclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
Line 2,410: Line 2,495:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover
 
#Re-attach the battery cover
  
Line 2,417: Line 2,502:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter inclusion mode
 
#Re-attach the battery cover and the device with enter inclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
 
#Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.
  
Line 2,427: Line 2,512:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Remove the battery for at least 5 seconds, then reinstall it.
+
#Remove the battery for at least '''5''' seconds, then reinstall it.
 
#Re-attach the battery cover and the device with enter exclusion mode
 
#Re-attach the battery cover and the device with enter exclusion mode
#The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
+
#The LED will flash for '''10''' seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.
  
 
<hr />
 
<hr />
Line 2,482: Line 2,567:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.
+
#To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor '''3''' times and hold for '''3''' seconds on the 3rd press.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,488: Line 2,573:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the inclusion/exclusion button on the sensor 3 times.
+
#Press the inclusion/exclusion button on the sensor '''3''' times.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,495: Line 2,580:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the inclusion/exclusion button on the sensor 3 times.
+
#Press the inclusion/exclusion button on the sensor '''3''' times.
  
 
<hr />
 
<hr />
Line 2,513: Line 2,598:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED will be steady on.
+
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
#Within 1 second, press and hold the tamper switch until LED is off.
+
#Within '''1''' second, press and hold the tamper switch until LED is off.
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,521: Line 2,606:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,528: Line 2,613:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
+
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.
  
 
<hr />
 
<hr />
Line 2,545: Line 2,630:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press link key three times within 1.5 second. The sensor will beep each time the link key is pressed.
+
#Press link key three times within '''1.5''' second. The sensor will beep each time the link key is pressed.
#Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
+
#Within '''1''' second, press and hold the link key. The sensor will long beep for '''5''' seconds. Keep holding the link key until the long beep stops.
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,553: Line 2,638:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing link key three times within 1.5 second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
+
#Pressing link key three times within '''1.5''' second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,560: Line 2,645:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing link key three times within 1.5 second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
+
#Pressing link key three times within '''1.5''' second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.
  
 
<hr />
 
<hr />
Line 2,577: Line 2,662:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED will be steady on.
+
#Press tamper switch three times within '''1.5''' second. The LED will be steady on.
#Within 1 second, press and hold the tamper switch until LED is off.
+
#Within '''1''' second, press and hold the tamper switch until LED is off.
#The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.
+
#The LED will cycle on for '''2''' seconds and off for '''2''' seconds indicating the sensor has been reset for factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,585: Line 2,670:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,592: Line 2,677:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second will enter exclusion mode.
+
#Pressing tamper switch three times within '''1.5''' second will enter exclusion mode.
  
 
<hr />
 
<hr />
Line 2,609: Line 2,694:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press tamper switch three times within 1.5 second. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Press tamper switch three times within '''1.5''' second. The LED flashes and the buzzer sounds when the link key is pressed.
#Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
+
#Within '''1''' second, press and hold the tamper switch for '''5''' seconds until the LED is off.
#The LED will light for 5 seconds and the buzzer will sound for 5 seconds
+
#The LED will light for '''5''' seconds and the buzzer will sound for '''5''' seconds
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,617: Line 2,702:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
#The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
+
#The detector will stay awake and remain in inclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
#The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has joined the Z-Wave network.
+
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has joined the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,626: Line 2,711:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing tamper switch three times within 1.5 second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
+
#Pressing tamper switch three times within '''1.5''' second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
#The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
+
#The detector will stay awake and remain in exclusion mode for '''10''' minutes, or until the device has successfully joined the Z-Wave network.,
#The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has been excluded from the Z-Wave network.
+
#The LED will light for '''1''' second and the buzzer will sound for '''1''' second to indicated the detector has been excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 2,645: Line 2,730:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
#Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
+
#Within '''1''' second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.
  
Line 2,653: Line 2,738:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,660: Line 2,745:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
+
#Pressing the temperature unit/linking key '''3''' times within '''1.5''' seconds will enter inclusion mode. The linking signal symbol will flash on the display.
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
 
#When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks
  
Line 2,682: Line 2,767:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Exclude the module by tapping the button three times, then press and hold for 10 seconds.
+
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
#*LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
+
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,689: Line 2,774:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the button on the once to include it in the Z-Wave network.
+
#Press the button on the device once to include it in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 2,696: Line 2,781:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Exclude the module by tapping the button three times, then press and hold for 10 seconds.
+
#Exclude the module by tapping the button '''3''' times, then press and hold for '''10''' seconds.
#*LFM-20 release 5.41 requires that you tap two times, then press and hold for 10 seconds.
+
#*LFM-20 release 5.41 requires that you tap '''2''' times, then press and hold for '''10''' seconds.
  
 
<hr />
 
<hr />
Line 2,717: Line 2,802:
  
 
#Click the Button exactly five times.
 
#Click the Button exactly five times.
#Press and hold the Button for at least 5 seconds.
+
#Press and hold the Button for at least '''5''' seconds.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,723: Line 2,808:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Click the button at least 6 times.
+
#Click the button at least '''6''' times.
 
#Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
#Click the button 4 times to wake it up
+
#Click the button '''4''' times to wake it up
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
  
Line 2,733: Line 2,818:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Click the Button at least six times.
+
#Click the Button at least '''6''' times.
 
#Wait for the removing process to end.
 
#Wait for the removing process to end.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
Line 2,754: Line 2,839:
 
#Open the cover and remove the battery.
 
#Open the cover and remove the battery.
 
#Install the battery while holding both TMP buttons.
 
#Install the battery while holding both TMP buttons.
#The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
+
#The LED indicator will be flashing slowly for '''5''' seconds, but keep holding the buttons.
 
#Release one button when the LED indicator starts flashing quickly.
 
#Release one button when the LED indicator starts flashing quickly.
 
#Click the released button once to confirm initiation of the reset procedure.
 
#Click the released button once to confirm initiation of the reset procedure.
 
#Wait a few seconds for a long flash of the LED indicator. '''Do not remove the battery'''.
 
#Wait a few seconds for a long flash of the LED indicator. '''Do not remove the battery'''.
#The LED indicator will flash 5 times quickly to confirm reset of the device.
+
#The LED indicator will flash '''5''' times quickly to confirm reset of the device.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 2,764: Line 2,849:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press one of the TMP buttons quickly, three times in a row, '''while keeping other button is pressed'''.
+
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 2,774: Line 2,859:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press one of the TMP buttons quickly, three times in a row, '''while keeping other button is pressed'''.
+
#Press one of the TMP buttons quickly, '''3''' times in a row, '''while keeping other button is pressed'''.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,803: Line 2,888:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Removed the battery for 10 seconds, and re-install it
+
#Removed the battery for '''10''' seconds, and re-install it
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 2,813: Line 2,898:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Press the TMP button quickly, '''3''' times in a row.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,842: Line 2,927:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Press the TMP button quickly, '''3''' times in a row.
 
#Wait for the inclusion process to end.
 
#Wait for the inclusion process to end.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 2,852: Line 2,937:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the TMP button quickly, three times in a row.
+
#Press the TMP button quickly, '''3''' times in a row.
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 2,914: Line 2,999:
 
#Wait for visual indicator to glow '''Yellow''' (2nd menu position).
 
#Wait for visual indicator to glow '''Yellow''' (2nd menu position).
 
#Release the '''B''' button and then briefly click the B-button to confirm selection
 
#Release the '''B''' button and then briefly click the B-button to confirm selection
#After few seconds the device will be reset, which is signaled with the red, fading visual indicator color.
+
#After few seconds the device will be reset, which is signaled with the '''Red''', fading visual indicator color.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,163: Line 3,248:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Power up the device with the test button held down for 10+ seconds
+
#Power up the device with the test button held down for '''10''' or more seconds
 
#The device will reset all Z-Wave settings and leave the network. '''NOTE: The device will not remain awake after resetting and will go into standby mode.'''
 
#The device will reset all Z-Wave settings and leave the network. '''NOTE: The device will not remain awake after resetting and will go into standby mode.'''
  
Line 3,197: Line 3,282:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Turn OFF the light for 3 second.
+
#Turn OFF the light for '''3''' second.
#Turn ON the light for 3 seconds
+
#Turn ON the light for '''3''' seconds
#Repeat this process 5 times
+
#Repeat this process '''5''' times
 
#The bulb will dim and then flash once when successfully reset.
 
#The bulb will dim and then flash once when successfully reset.
  
Line 3,556: Line 3,641:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
#The LED will flash ON/OFF 5 times when completed successfully.
+
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,571: Line 3,656:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
 
#Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
+
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,588: Line 3,673:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press the manual/program button 3 times, then press and hold the button for at least 3 seconds. The LED will flash 5 times to confirm.
+
#Press the manual/program button '''3''' times, then press and hold the button for at least '''3''' seconds. The LED will flash '''5''' times to confirm.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,618: Line 3,703:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
#The LED will flash ON/OFF 5 times when completed successfully.
+
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,633: Line 3,718:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
 
#Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
+
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,650: Line 3,735:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times.
+
#Quickly press ON (Top) button '''3''' times then immediately press the OFF (Bottom) button '''3''' times.
#The LED will flash ON/OFF 5 times when completed successfully.
+
#The LED will flash ON/OFF '''5''' times when completed successfully.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,665: Line 3,750:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
 
#Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
+
#*Note: While some switches have a small tab to pull out, commonly referred to as an '''Air Gap,''' certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains powered device is refusing to join Hubitat Elevation™, try '''Z-Wave Exclude''' and then cut the power at the breaker box for '''30''' seconds before attempting the discovery procedure again.
  
 
<hr />
 
<hr />
Line 3,682: Line 3,767:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the top button '''10 times''' within five seconds.
+
#Press and release the top button '''10''' times within '''5''' seconds.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,712: Line 3,797:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the top button '''10 times''' within five seconds. The LED will flash 3 times quickly confirming change
+
#Press and release the top button '''10''' times within '''5''' seconds. The LED will flash '''3''' times quickly confirming change
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,743: Line 3,828:
  
 
#If plugged in, unplug the Dimmer from the receptacle.
 
#If plugged in, unplug the Dimmer from the receptacle.
#Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
+
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,774: Line 3,859:
  
 
#If plugged in, unplug the Dimmer from the receptacle.
 
#If plugged in, unplug the Dimmer from the receptacle.
#Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
+
#Press and hold the top button for at least '''3''' seconds while you plug the dimmer into a receptacle.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,804: Line 3,889:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and release the program button ten times quickly.
+
#Press and release the program button '''10''' times quickly.
 
#The LED light will flash approximately eight times.
 
#The LED light will flash approximately eight times.
  
Line 3,835: Line 3,920:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the top of the rocker (ON Switch) 10x quickly (short presses)
+
#Tap the top of the rocker (ON Switch) with '''10''' quick short presses.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 3,869: Line 3,954:
 
#Hold down the UP button
 
#Hold down the UP button
 
#Push In the air-gap switch to ON position to power up the device.
 
#Push In the air-gap switch to ON position to power up the device.
#Release the UP button within 4 seconds of power up.
+
#Release the UP button within '''4''' seconds of power up.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 3,877: Line 3,962:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Restore power to the Smart Dimmer at the circuit breaker
 
#Restore power to the Smart Dimmer at the circuit breaker
#Pairing Begins Automatically: LED Status Indicator flashs as the Smart Dimmer automatically scans for a compatible network controller to pair with.
+
#Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
 
#After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
 
#*'''Note:''' ''LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
 
#*'''Note:''' ''LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart pairing process following timeout.''
Line 3,903: Line 3,988:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Reset the controller by pressing the Link button 5 times.
+
#Reset the controller by pressing the Link button '''5''' times.
#A quick beep followed by a longer beep will indicate proper reset of the GD00Z series or ND00Z.
+
#A quick beep followed by a longer beep will indicate proper reset for the GD00Z series or ND00Z.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,936: Line 4,021:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
+
#Press the program switch of WADWAZ-1 for '''1''' second and release. The LED light will flash continuously when the sensor has been successfully excluded.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 3,951: Line 4,036:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the program switch of WADWAZ-1 for 1 second and release. The LED light will flash continuously when the sensor has been successfully excluded.
+
#Press the program switch of WADWAZ-1 for '''1''' second and release. The LED light will flash continuously when the sensor has been successfully excluded.
  
 
<hr />
 
<hr />
Line 3,971: Line 4,056:
 
'''Network Reset'''
 
'''Network Reset'''
  
#Press and hold the button on the headrail end cap for 7 seconds or until the shade jogs once.
+
#Press and hold the button on the headrail end cap for '''7''' seconds or until the shade jogs once.
 
#Release the button.
 
#Release the button.
 
#*NOTE: The will not reset the shade limits
 
#*NOTE: The will not reset the shade limits
Line 3,979: Line 4,064:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash '''Green.'''
+
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash '''Green.'''
 
#Release the button.
 
#Release the button.
 
#Successful inclusion will be confirmed by Hubitat Elevation™
 
#Successful inclusion will be confirmed by Hubitat Elevation™
Line 3,989: Line 4,074:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED lightbar begins to flash '''Green.'''
+
#Place the single channel remote in programming mode by pressing and holding the programming button until the LED light bar begins to flash '''Green.'''
 
#Release the button
 
#Release the button
 
#The shade will be excluded from the Z-Wave network.
 
#The shade will be excluded from the Z-Wave network.
Line 4,011: Line 4,096:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#To reset, hold down center button for approximately 20+ seconds.
+
#To reset, hold down center button for approximately '''20''' or more seconds.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,018: Line 4,103:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Once Halo greets you, it will automatically begin searching for a ZigBee network. Halo will glow for a couple minutes before timing out.
 
#Once Halo greets you, it will automatically begin searching for a ZigBee network. Halo will glow for a couple minutes before timing out.
#*To awaken the detector, double-tap the center button or hold the button for approximately 3+ seconds.
+
#*To awaken the detector, double-tap the center button or hold the button for approximately '''3''' or more seconds.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Hold down the center button for approximately 20+ seconds. Halo will reset all ZigBee settings and leave the network. .
+
#Hold down the center button for approximately '''20''' ot more seconds. Halo will reset all ZigBee settings and leave the network. .
  
 
<hr />
 
<hr />
Line 4,043: Line 4,128:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Turn off your fan for 3 seconds, then turn it on for 3 seconds (Repeat 5 times)
+
#Turn off your fan for '''3''' seconds, then turn it on for '''3''' seconds (Repeat '''5''' times)
 
#The light will flash three times when the factory reset is successful.
 
#The light will flash three times when the factory reset is successful.
  
Line 4,056: Line 4,141:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Perform a factory reset on the controller
+
#Perform a factory reset on the fan controller
  
 
<hr />
 
<hr />
Line 4,077: Line 4,162:
  
 
#Press and holding the center "Z-button" for 20 seconds.
 
#Press and holding the center "Z-button" for 20 seconds.
#Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
+
#Release the button after '''20''' seconds and the LED will stay yellow for '''3''' seconds.
#Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
+
#Within the '''3''' second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,086: Line 4,171:
 
#Insert the battery.
 
#Insert the battery.
 
#Triple click the center "Z-button".
 
#Triple click the center "Z-button".
#If inclusion is successful, the LED will flash '''blue''' for less than 5 seconds, and then it will remain solid for 15 seconds.
+
#If inclusion is successful, the LED will flash '''blue''' for less than '''5''' seconds, and then it will remain solid for '''15''' seconds.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,093: Line 4,178:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#If exclusion is successful, the LED will flash '''orange''' for less than 5 seconds, and then it will remain solid for 3 seconds.
+
#If exclusion is successful, the LED will flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
  
 
<hr />
 
<hr />
Line 4,112: Line 4,197:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and holding the center "Z-button" for 20 seconds.
+
#Press and holding the center "Z-button" for '''20''' seconds.
#Release the button after 20 seconds and the LED will stay yellow for 3 seconds.
+
#Release the button after '''20''' seconds and the LED will stay yellow for '''3''' seconds.
#Within the 3 second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
+
#Within the '''3''' second period where the LED is yellow, short-press the Z-button to reset the controller to factory defaults.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,122: Line 4,207:
 
#Insert the battery.
 
#Insert the battery.
 
#Triple click the center "Z-button".
 
#Triple click the center "Z-button".
#If inclusion is successful, the LED will flash '''blue''' for less than 5 seconds, and then it will remain solid for 15 seconds.
+
#If inclusion is successful, the LED will flash '''blue''' for less than '''5''' seconds, and then it will remain solid for '''15''' seconds.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,129: Line 4,214:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#If exclusion is successful, the LED will flash '''orange''' for less than 5 seconds, and then it will remain solid for 3 seconds.
+
#If exclusion is successful, the LED will flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
  
 
<hr />
 
<hr />
Line 4,151: Line 4,236:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Toggle power to the bulb off and on 3 times quickly.
+
#Toggle power to the bulb off and on '''3''' times quickly.
#Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
+
#Within '''3''' times toggling the bulb, the final ending state of the switch or plug must be on.
#If the exclusion is successful, the RGB BULB will quicly flash '''orange''' for less than 5 seconds, and then it will remain solid for 3 seconds.
+
#If the exclusion is successful, the RGB BULB will quicly flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
  
Line 4,168: Line 4,253:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Toggle power to the bulb off and on 3 times quickly.
+
#Toggle power to the bulb off and on '''3''' times quickly.
#Within 3 times toggling the bulb, the final ending state of the switch or plug must be on.
+
#Within '''3''' times toggling the bulb, the final ending state of the switch or plug must be on.
#If the exclusion is successful, the RGB BULB will quicly flash '''orange''' for less than 5 seconds, and then it will remain solid for 3 seconds.
+
#If the exclusion is successful, the RGB BULB will quickly flash '''orange''' for less than '''5''' seconds, and then it will remain solid for '''3''' seconds.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
 
#The bulb will remain '''warm white''' after the exclusion procedure is complete.
  
Line 4,194: Line 4,279:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Tap the button on the front of the module once
+
#Tap the button on the front of the module once.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,200: Line 4,285:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Tap the button on the front of the module once
+
#Tap the button on the front of the module once.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,207: Line 4,292:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Tap the button on the front of the module once
+
#Tap the button on the front of the module once.
  
 
<hr />
 
<hr />
Line 4,230: Line 4,315:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the Z-Wave button inside the sensor body for 10 seconds
+
#Press and hold the Z-Wave button inside the sensor body for '''10''' seconds
#If successful, the LED will flash 5 times.
+
#If successful, the LED will flash '''5''' times.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,266: Line 4,351:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the Z-Wave button inside the sensor body for 10 seconds
+
#Press and hold the Z-Wave button inside the sensor body for '''10''' seconds
#If successful, the LED will flash 5 times.
+
#If successful, the LED will flash '''5''' times.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,300: Line 4,385:
  
 
#Turn dimmer on by tapping the top of the paddle once.
 
#Turn dimmer on by tapping the top of the paddle once.
#Quickly tap top of the paddle 3 times.
+
#Quickly tap top of the paddle '''3''' times.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
  
Line 4,334: Line 4,419:
  
 
#Turn dimmer on by tapping the top of the paddle once.
 
#Turn dimmer on by tapping the top of the paddle once.
#Quickly tap top of the paddle 3 times.
+
#Quickly tap top of the paddle '''3''' times.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
 
#If light turns off and then on again, the dimmer is reset. If not, repeat manual reset.
  
Line 4,367: Line 4,452:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Z-Wave button inside the sensor body for 20 seconds, the LED will stay on until the button is released.
+
#Press and hold the Z-Wave button inside the sensor body for '''20''' seconds, the LED will stay on until the button is released.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,374: Line 4,459:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
 
#Triple-click the Z-Wave button inside the sensor body and wait for the process to finish.
#If successful, the sensor body LED will flash briefly and then stay on for 3 seconds.
+
#If successful, the sensor body LED will flash briefly and then stay on for '''3''' seconds.
 
#If unsuccessful, the LED with flash briefly and then turn off. Should this happen, repeat the inclusion process.
 
#If unsuccessful, the LED with flash briefly and then turn off. Should this happen, repeat the inclusion process.
  
Line 4,383: Line 4,468:
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#Triple-click the Z-Wave button inside the sensor body.
 
#Triple-click the Z-Wave button inside the sensor body.
#If successful, the LED will turn off within 1 second.
+
#If successful, the LED will turn off within '''1''' second.
#If unsuccessful, the LED with flash for 5 seconds. Should this happen, repeat the exclusion process.
+
#If unsuccessful, the LED with flash for '''5''' seconds. Should this happen, repeat the exclusion process.
  
 
<hr />
 
<hr />
Line 4,403: Line 4,488:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Z-Wave button for 20 seconds. Release the button once the LED stops flashing and glows solidly
+
#Press and hold the Z-Wave button for '''20''' seconds. Release the button once the LED stops flashing and glows solidly
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,436: Line 4,521:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
+
#Cycle power '''6''' times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
#Wait for at least 10 seconds after reset is complete before attempting to pair the bulb.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the bulb.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,443: Line 4,528:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has successfully joined the Zigbee network.
+
#Cycle power '''6''' times. The bulb will begin to dim and finally flash '''1''' time to indicate that it has successfully joined the Zigbee network.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
+
#Cycle power '''6''' times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
#Wait for at least 10 seconds after reset is complete before attempting to pair the bulb again.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the bulb again.
  
 
<hr />
 
<hr />
Line 4,469: Line 4,554:
  
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
#Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
+
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
#Wait for at least 10 seconds after reset is complete before attempting to pair the device.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,478: Line 4,563:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
#Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
+
#Press and hold the paperclip in the hole for '''2-4''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
 
#The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
  
Line 4,485: Line 4,570:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
 
#Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
#Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
+
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the outlet).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
#Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device again.
  
 
<hr />
 
<hr />
Line 4,507: Line 4,592:
  
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
#Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
+
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#An LED will pulse quickly and then pulse slowly when you release the internal button.
 
#An LED will pulse quickly and then pulse slowly when you release the internal button.
#Wait for at least 10 seconds after reset is complete before attempting to pair the device.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,516: Line 4,601:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
#Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
+
#Press and hold the paperclip in the hole for '''2-4''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
 
#The LED will pulse pulse slowly when before pairing and will be steady when pairing has been successfully completed.
 
#The signal repeater will pair as '''Device'''. No driver will be assigned and it is not necessary to have one since this device only repeats Zigbee radio signals.
 
#The signal repeater will pair as '''Device'''. No driver will be assigned and it is not necessary to have one since this device only repeats Zigbee radio signals.
Line 4,524: Line 4,609:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
 
#Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
#Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
+
#Press and hold the paperclip in the hole for at least '''5''' seconds (you will feel the paperclip depressing a tiny button inside the repeater).
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
 
#The LED will pulse quickly and then pulse slowly when you release the internal button.
#Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
+
#Wait for at least '''10''' seconds after reset is complete before attempting to pair the device again.
  
 
<hr />
 
<hr />
Line 4,546: Line 4,631:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Hold the UP button for 5 seconds when powered on
+
#Hold the UP button for '''5''' seconds when powered on
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,552: Line 4,637:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Top button on the switch 6 times within 2 seconds.
+
#Press the Top button on the switch '''6''' times within '''2''' seconds.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,559: Line 4,644:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Top button on the switch 6 times within 2 seconds.
+
#Press the Top button on the switch '''6''' times within '''2''' seconds.
  
 
<hr />
 
<hr />
Line 4,578: Line 4,663:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the top button for at least 3 seconds while you plug the outlet into a recepticle
+
#Press and hold the top button for at least '''3''' seconds while you plug the outlet into a recepticle
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,584: Line 4,669:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Once the controller is ready to include your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
+
#Once the controller is ready to include your device, press in and release the button on the switch '''3-5''' times within '''3''' seconds to include it in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,591: Line 4,676:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Once the controller is ready to exclude your device, press in and release the button on the switch 3-5 times within 3 seconds to include it in the network.
+
#Once the controller is ready to exclude your device, press in and release the button on the switch '''3-5''' times within '''3''' seconds to include it in the network.
  
 
<hr />
 
<hr />
Line 4,610: Line 4,695:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Factory reset is acomplished by performing a general exclusion on the device.
+
#Factory reset is accomplished by performing a general exclusion on the device.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the center button 5 times within 1 second to exclude it in the Z-Wave network.
+
#Press the center button '''5''' times within '''1''' second to exclude it in the Z-Wave network.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 4,619: Line 4,704:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the center button 5 times within 1 second to include it in the Z-Wave network.
+
#Press the center button '''5''' times within '''1''' second to include it in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 4,626: Line 4,711:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the center button 5 times within 1 second to exclude it in the Z-Wave network.
+
#Press the center button '''5''' times within '''1''' second to exclude it in the Z-Wave network.
  
 
<hr />
 
<hr />
Line 4,649: Line 4,734:
  
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
+
#Within '''10''' seconds of reinserting the battery press the reset button next to the battery '''8''' times in a row, once per second.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#*'''NOTE:''' ''The green light can be dim, if you're in a well lighted area this light could be difficult to see.''
 
#*'''NOTE:''' ''The green light can be dim, if you're in a well lighted area this light could be difficult to see.''
Line 4,670: Line 4,755:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
 
#Squeeze the two sides of the smart button together by the ridges and gently pull them apart to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery press the reset button next to the battery eight times in a row, once per second.
+
#Within 10 seconds of reinserting the battery press the reset button next to the battery '''8''' times in a row, once per second.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#Upon a successful reset, the smart button will flash green indicating the device is now ready to pair.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see.''
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see.''
Line 4,696: Line 4,781:
  
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to flash.
+
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the pendant should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,715: Line 4,800:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the pendant should begin to flash.
+
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the pendant should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,738: Line 4,823:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
+
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait '''10''' seconds.
#Reinsert the battery and immediately press the white reset button 8 times.
+
#Reinsert the battery and immediately press the white reset button '''8''' times.
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
Line 4,757: Line 4,842:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait 10 seconds.
+
#Squeeze the sides and pop open the sensor to reveal the battery, remove the battery and wait '''10''' seconds.
#Reinsert the battery and immediately press the white reset button 8 times.
+
#Reinsert the battery and immediately press the white reset button '''8''' times.
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#Your Iris Contact Sensor should now be flashing green indicating it's ready to pair
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
Line 4,782: Line 4,867:
  
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to flash.
+
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the key fob should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,801: Line 4,886:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
 
#Insert the supplied access tool into the small opening at the top of the key fob. Gently pry open the case to reveal the battery compartment.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#Within 10 seconds of reinserting the battery, press either button eight times in a row, once per second. The lights on the key fob should begin to flash.
+
#Within '''10''' seconds of reinserting the battery, press either button '''8''' times in a row, once per second. The lights on the key fob should begin to flash.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,825: Line 4,910:
  
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.  
+
#As soon as the battery is reinserted, press the reset button '''8''' times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.  
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,844: Line 4,929:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
 
#Squeeze the raised edges on the sides of the motion sensor to take it apart to expose the battery.
#Remove the battery for at least 10 seconds. Reinsert the battery.
+
#Remove the battery for at least '''10''' seconds. Reinsert the battery.
#As soon as the battery is reinserted, press the reset button eight times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.  
+
#As soon as the battery is reinserted, press the reset button '''8''' times in a row, once per second. The lights on the top right corner of the motion sensor should begin to flash. (You may have to make a shadow over the device to see the flashing light). Once the light is flashing you're ready to pair.  
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*'''NOTE:''' ''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
  
Line 4,868: Line 4,953:
  
 
#Remove the Smart Plug from the receptacle.
 
#Remove the Smart Plug from the receptacle.
#Press and hold the button on the front for 15 seconds.
+
#Press and hold the button on the front for '''15''' seconds.
 
#Insert the Smart Plug back into the receptacle.
 
#Insert the Smart Plug back into the receptacle.
#Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.
+
#Immediately press the button on the front of the Smart Plug '''8''' times, allowing 1 second between each press.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 4,885: Line 4,970:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Remove the Smart Plug from the receptacle.
 
#Remove the Smart Plug from the receptacle.
#Press and hold the button on the front for 15 seconds.
+
#Press and hold the button on the front for '''15''' seconds.
 
#Insert the Smart Plug back into the receptacle.
 
#Insert the Smart Plug back into the receptacle.
#Immediately press the button on the front of the Smart Plug 8 times, allowing 1 second between each press.
+
#Immediately press the button on the front of the Smart Plug '''8''' times, allowing 1 second between each press.
  
 
<hr />
 
<hr />
Line 4,908: Line 4,993:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove battery. Wait 10 seconds then re-insert battery.
+
#Remove battery. Wait '''10''' seconds then re-insert battery.
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than flash blue (even more faintly).
+
#Within '''10''' seconds after re-inserting battery, press the button '''8''' times. The light will very dimly flash solid blue, than flash blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
Line 4,927: Line 5,012:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Remove battery. Wait 10 seconds then re-insert battery.
+
#Remove battery. Wait '''10''' seconds then re-insert battery.
#Within 10 seconds after re-inserting battery, press the button 8 times. The light will very dimly flash solid blue, than flash blue (even more faintly).
+
#Within '''10''' seconds after re-inserting battery, press the button '''8''' times. The light will very dimly flash solid blue, than flash blue (even more faintly).
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*'''NOTES:''' ''The + side of the battery should be facing the bottom of the button when you insert the tray. At this point, a blue light should be flashing on the button's top. If you don't see this, take the battery back out and try again.''
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
 
#*''The LED can be dim, if you're in a well lighted area this light could be difficult to see''.
Line 4,951: Line 5,036:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Slide off the battery cover, remove the battery and wait ten seconds.
+
#Slide the battery cover off, remove the battery and wait '''10''' seconds.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
#'''Hold for an additional two seconds''' and release. The contact sensor should begin flashing blue.
+
#Hold the reset button for an additional '''2''' seconds and release. The contact sensor should begin flashing blue.
 
#*'''NOTE:''' ''The reset button is a small black button above the battery.''
 
#*'''NOTE:''' ''The reset button is a small black button above the battery.''
  
Line 4,961: Line 5,046:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove battery. Wait 10 seconds then re-insert battery.
+
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
 
#After pairing test your Iris Contact Sensor is working by opening and closing the door or window it's set up on (The LED should flash GREEN when opened/closed)
Line 4,969: Line 5,054:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Slide off the battery cover, remove the battery and wait ten seconds.
+
#Slide the battery cover off, remove the battery and wait '''10''' seconds.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
 
#Using a paper clip, press and hold the reset button completely down while reinserting the battery.
#'''Hold for an additional two seconds''' and release. The contact sensor should begin flashing blue.
+
#Hold the reset button for an additional '''2''' seconds and release. The contact sensor should begin flashing blue.
 
#*'''NOTE:''' ''The reset button is a small black button above the battery''
 
#*'''NOTE:''' ''The reset button is a small black button above the battery''
  
Line 4,993: Line 5,078:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Unplug your device - wait 10 seconds
+
#Unplug your device and wait '''10''' seconds
 
#Restore power to the device
 
#Restore power to the device
#Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
+
#Press the Link (Z-Wave) button on the left side of the device '''5''' times within '''10''' seconds to reset your device.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 5,035: Line 5,120:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove the battery and wait ten seconds.
+
#Remove the battery and wait '''10''' seconds.
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
+
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for '''2''' seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
Line 5,046: Line 5,131:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove battery. Wait 10 seconds then re-insert battery.
+
#Remove battery. Wait '''10''' seconds then re-insert battery.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 5,053: Line 5,138:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for two seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
+
#Press and hold the tamper switch while inserting one battery. Hold tamper switch for '''2''' seconds after the battery is installed. The tamper switch is the little flat plastic tab located on the back where the mounting bracket connects to the device, it is above the battery compartment.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#*Note: The factory reset process puts the security keypad back into pairing mode.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
 
#Upon a proper reset the top right icon will be flashing green on your keypad.
Line 5,077: Line 5,162:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove only 1 AA battery and wait ten seconds.
+
#Remove only 1 AA battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashs red once.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#A flashing blue light indicates the device is reset and ready to pair again.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
  
#Remove only 1 AA battery and wait ten seconds.
+
#Remove only 1 AA battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashs red once.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
Line 5,094: Line 5,179:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Remove only 1 AA battery and wait ten seconds.
+
#Remove only 1 AA battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashs red once.
+
#Re-insert the battery while holding down the reset button on the left side of the keypad and release when the status light flashes Red once.
#A flashing blue light indicates the device is reset and ready to pair again.
+
#A flashing Blue light indicates the device is reset and ready to pair again.
  
 
<hr />
 
<hr />
Line 5,117: Line 5,202:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove the battery and wait 10 seconds
+
#Remove the battery and wait '''10''' seconds
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
#Hold for an additional two seconds and release.
+
#Hold for an additional '''2''' seconds and release.
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
#Upon a successful reset your device will now be flashing blue - indicating it's ready to pair.
+
#Upon a successful reset your device will now be flashing Blue, indicating it's ready to pair.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#A flashing blue light indicates the device is reset and ready to pair again.
  
Line 5,129: Line 5,214:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery for 10 seconds and re-insert.
+
#Remove the battery for '''10''' seconds and re-insert.
#Replace the battery cover. The sensor's blue LED will flash while searching for the hub.
+
#Replace the battery cover. The sensor's Blue LED will flash while searching for the hub.
 
#Once paired the LED will stop flashing.
 
#Once paired the LED will stop flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
Line 5,139: Line 5,224:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
 
#Press and hold the reset button on the left side of the device as you reinsert the battery.
#Hold for an additional two seconds and release.
+
#Hold for an additional '''2''' seconds and release.
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
 
#*'''Note:''' ''The reset button is a small white button located on the side of the motion sensor.''
#Upon a successful reset your device will now be flashing blue - indicating it's ready to pair.
+
#Upon a successful reset your device will now be flashing Blue, indicating it's ready to pair.
 
#A flashing blue light indicates the device is reset and ready to pair again.
 
#A flashing blue light indicates the device is reset and ready to pair again.
  
Line 5,163: Line 5,248:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove the battery and wait ten seconds.
+
#Remove the battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
+
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
#A flashing blue light indicates the device is ready to pair.
+
#A flashing Blue light indicates the device is ready to pair.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,171: Line 5,256:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery and wait ten seconds.
+
#Remove the battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
+
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
#A flashing blue light indicates the device is ready to pair.
+
#A flashing Blue light indicates the device is ready to pair.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 5,180: Line 5,265:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Remove the battery and wait ten seconds.
+
#Remove the battery and wait '''10''' seconds.
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns red.
+
#Re-insert the battery while holding down the reset button on the left side and release when the status light turns Red.
#A flashing blue light indicates the device is ready to pair.
+
#A flashing Blue light indicates the device is ready to pair.
  
 
<hr />
 
<hr />
Line 5,203: Line 5,288:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove the Smart Plug from the outlet and wait ten seconds.
+
#Remove the Smart Plug from the outlet and wait '''10''' seconds.
 
#Press and hold the small white button on the front of the plug.
 
#Press and hold the small white button on the front of the plug.
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#As soon as the LED on the front of the plug lights up, release the button.
 
#As soon as the LED on the front of the plug lights up, release the button.
#If the reset was successful the blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
+
#If the reset was successful the Blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,214: Line 5,299:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Insert your smart plug into any wall outlet. Your smart plug should be flashing blue, that means it's in pairing mode.
+
#Insert your smart plug into any wall outlet. Your smart plug should be flashing Blue, that means it's in pairing mode.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 5,224: Line 5,309:
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#While holding the button, insert the Smart Plug back into the outlet.
 
#As soon as the LED on the front of the plug lights up, release the button.
 
#As soon as the LED on the front of the plug lights up, release the button.
#If the reset was successful the blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
+
#If the reset was successful the Blue LED on the front of the smart plug will be flashing. This means your smart plug is now ready to pair.
  
 
<hr />
 
<hr />
Line 5,246: Line 5,331:
  
 
#Twist open the battery cover on the back of the Smart Fob.
 
#Twist open the battery cover on the back of the Smart Fob.
#Remove the battery and wait ten seconds
+
#Remove the battery and wait '''10''' seconds
 
#Reinstall the battery with the positive side facing you.
 
#Reinstall the battery with the positive side facing you.
#Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
+
#Once the battery is installed, push any of the four buttons '''8''' times in a row, once per second.
#Confirm that the fob has been reset by checking that the fob's background light is flashing blue. If it does not do this, check the battery and retry from step 2.
+
#Confirm that the fob has been reset by checking that the fob's background light is flashing Blue. If it does not do this, check the battery and retry from step 2.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,257: Line 5,342:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
 
#Insert the battery so the plus sign is facing you. Put the cover on and twist tighten with a coin.
#The Smart Fob's LED will flash blue while searching for the hub.
+
#The Smart Fob's LED will flash Blue while searching for the hub.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 5,265: Line 5,350:
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#Twist open the battery cover on the back of the Smart Fob.
 
#Twist open the battery cover on the back of the Smart Fob.
#Remove the battery and wait ten seconds
+
#Remove the battery and wait '''10''' seconds
 
#Reinstall the battery with the positive side facing you.
 
#Reinstall the battery with the positive side facing you.
#Once the battery is installed, push any of the four buttons 8 times in a row, once per second.
+
#Once the battery is installed, push any of the four buttons '''8''' times in a row, once per second.
  
 
<hr />
 
<hr />
Line 5,288: Line 5,373:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Remove the cover from the sensor, then remove the battery for at least 10 seconds.
+
#Remove the cover from the sensor, then remove the battery for at least '''10''' seconds.
 
#Press and hold the reset button while reinserting the battery.
 
#Press and hold the reset button while reinserting the battery.
#Hold for an additional two seconds and release.
+
#Hold for an additional '''2''' seconds and release.
#A successful reset will be indicated by a flashing blue light on your sensor
+
#A successful reset will be indicated by a flashing Blue light on your sensor
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,298: Line 5,383:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Remove the battery and wait ten seconds.
+
#Remove the battery and wait '''10''' seconds.
 
#Re-insert the battery
 
#Re-insert the battery
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
Line 5,306: Line 5,391:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Remove the cover from the sensor, then remove the battery for at least 10 seconds.
+
#Remove the cover from the sensor, then remove the battery for at least '''10''' seconds.
 
#Press and hold the reset button while reinserting the battery.
 
#Press and hold the reset button while reinserting the battery.
#Hold for an additional two seconds and release.
+
#Hold for an additional '''2''' seconds and release.
#A successful reset will be indicated by a flashing blue light on your sensor
+
#A successful reset will be indicated by a flashing Blue light on your sensor
  
 
<hr />
 
<hr />
Line 5,330: Line 5,415:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press the black button on the back inside of the Smart Vent battery compartment five times.
+
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
#You will know that the Smart Vent has been properly reset when the LED starts double flashing green
+
#You will know that the Smart Vent has been properly reset when the LED starts double flashing Green
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,338: Line 5,423:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Removed the battery cartridge and reinsert it to bring the vent online.
 
#Removed the battery cartridge and reinsert it to bring the vent online.
#Press the black button on the back inside of the Smart Vent battery compartment five times.
+
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
 
#This should force the vent into join-mode once again.
 
#This should force the vent into join-mode once again.
  
Line 5,344: Line 5,429:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Press the black button on the back inside of the Smart Vent battery compartment five times.
+
#Press the black button on the back inside of the Smart Vent battery compartment '''5''' times.
#You will know that the Smart Vent has been properly reset when the LED starts double flashing green
+
#You will know that the Smart Vent has been properly reset when the LED starts double flashing Green
  
 
<hr />
 
<hr />
Line 5,364: Line 5,449:
  
 
#Remove battery pack
 
#Remove battery pack
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
+
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for '''30''' seconds until the lock beeps and the status LED flashes Red.
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
+
#Press the Program button once more. When the LED flashes Green and you hear one beep, the lock has been reset.
 
#Perform the '''door handing''' process again.
 
#Perform the '''door handing''' process again.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
+
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait '''15''' seconds, before attempting the handing process again.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 5,376: Line 5,461:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
+
#Press button '''A''' on the lock one time to include it. The controller and lock must remain stationary for a total of '''60''' seconds during the Inclusion process.
 
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#If Inclusion is unsuccessful, go to the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
Line 5,386: Line 5,471:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of 60 seconds during the Inclusion process.
+
#Press button '''A''' on the lock one time. Once the lock is fully Excluded from the system. The controller and lock must remain stationary for a total of '''60''' seconds during the Inclusion process.
  
 
<hr />
 
<hr />
Line 5,404: Line 5,489:
  
 
#Remove battery pack
 
#Remove battery pack
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.
+
#Press and HOLD the Program button while reinserting the battery pack. Keep holding the button for '''30''' seconds until the lock beeps and the status LED flashes Red.
#Press the Program button once more. When the LED flashes green and you hear one beep, the lock has been reset.
+
#Press the Program button once more. When the LED flashes Green and you hear one beep, the lock has been reset.
 
#Perform the '''door handing''' process again.
 
#Perform the '''door handing''' process again.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Press and hold the Lock button while installing battery pack.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
 
#*Hold button until the latch bolt starts moving on its own. If the latch bolt retract and extend on its own when the battery pack was installed, then the handing process was successful.
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait 15 seconds, before attempting the handing process again.
+
#*If the latch bolt does not retract and extend on its own, remove the battery pack and wait '''15''' seconds, before attempting the handing process again.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 5,416: Line 5,501:
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#From the Hubitat Web Interface home page, select '''Zigbee''' on the '''Device Discovery''' page to start device discovery.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press button '''A''' on the lock '''4 times''' to pair it. The controller and lock must remain stationary for a total of 60 seconds during the pairing process.
+
#Press button '''A''' on the lock '''4''' times to pair it. The controller and lock must remain stationary for a total of '''60''' seconds during the pairing process.
#*If pairing is unsuccessful, press button '''B''' on the lock '''9 times''' and repeat the pairing process.
+
#*If pairing is unsuccessful, press button '''B''' on the lock '''9''' times and repeat the pairing process.
  
 
'''Leaving the Zigbee Network'''
 
'''Leaving the Zigbee Network'''
  
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
 
#From the device's details page, select '''Remove Device''', then '''Remove.'''
#Press button '''B''' on the lock '''9 times.'''
+
#Press button '''B''' on the lock '''9''' times'''.'''
  
 
<hr />
 
<hr />
Line 5,443: Line 5,528:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Unplug your device - wait 10 seconds
+
#Unplug your device and wait '''10''' seconds
 
#Restore power to the device
 
#Restore power to the device
#Press the Link (Z-Wave) button on the left side of the device 5 times within 10 seconds to reset your device.
+
#Press the Link (Z-Wave) button on the left side of the device '''5''' times within '''10''' seconds to reset your device.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 5,478: Line 5,563:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#On the 4-Scene controller, press and hold buttons 1 and 3.
+
#On the 4-Scene controller, press and hold buttons '''1''' and '''3'''.
#Wait approximately 5 seconds until the LED turns amber and then solid red.
+
#Wait approximately '''5''' seconds until the LED turns amber and then solid red.
 
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
 
#Release the buttons and the 4-Scene controller will be reset. '''NOTE: Factory reset does not exclude the device from any previous networks it has joined. The exclusion process must still be performed separately.'''
  
Line 5,509: Line 5,594:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Depress the Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
+
#Depress the Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#The LED on the sensor will stop flashing
Line 5,519: Line 5,604:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Tamper switch of WADWAZ-1 for 1 second and release to exclude the device form the Z-wave network.
+
#Press the Tamper switch of WADWAZ-1 for '''1''' second and release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
  
Line 5,545: Line 5,630:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Depress the Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
+
#Depress the Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#The LED on the sensor will stop flashing
Line 5,555: Line 5,640:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the Tamper switch of WAPIRZ-1 for 1 second and release to exclude the device form the Z-wave network.
+
#Press the Tamper switch of WAPIRZ-1 for '''1''' second and release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
  
Line 5,581: Line 5,666:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
+
#Press the siren/strobe Program/Tamper switch for '''1''' second then release. The LED on the sensor will begin flashing.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#The LED on the sensor will stop flashing
 
#The LED on the sensor will stop flashing
Line 5,591: Line 5,676:
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
+
#Press the siren/strobe Program/Tamper switch for '''1''' second then release to exclude the device form the Z-wave network.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
 
#The LED light will flash continuously when the sensor is in the excluded condition.
  
Line 5,610: Line 5,695:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the "On" button quickly three times, holding on the last press.
+
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Continue to hold the "On" button until the light begins to flash quickly.
#Release the button, then immediately tap the button three more times.
+
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
  
Line 5,639: Line 5,724:
 
|}'''Network Reset'''
 
|}'''Network Reset'''
  
#First, press and hold the black button on the back of your Smart Bridge for 20 seconds.
+
#First, press and hold the black button on the back of your Smart Bridge for '''20''' seconds.
  
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Quickly triple tap and hold the Add button. DO NOT release after the third tap.
+
#Quickly tap the button '''3''' times and hold. '''DO NOT release after the third tap'''.
 
#Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
 
#Continue to hold the Add button for a few seconds. The LEDs will begin to flash slowly (approximately once per second).
#Release the button and quickly perform another triple tap of the button. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
+
#Release the button and quickly tap the button '''3''' times. The LEDs will flash quickly and then will turn off. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly)
 
#The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
 
#The Lutron Smart Bridge Pro has now been returned to Factory Default Settings.
  
Line 5,663: Line 5,748:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the "On" button quickly three times, holding on the last press.
+
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Continue to hold the "On" button until the light begins to flash quickly.
#Release the button, then immediately tap the button three more times.
+
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
  
Line 5,692: Line 5,777:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the "On" button quickly three times, holding on the last press.
+
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Continue to hold the "On" button until the light begins to flash quickly.
#Release the button, then immediately tap the button three more times.
+
#Release the button, then immediately tap the button '''3''' more times.
 
#The RA2 keypad has now been returned to Factory Default Settings.
 
#The RA2 keypad has now been returned to Factory Default Settings.
  
Line 5,721: Line 5,806:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Triple tap and hold the Test button on a Main Repeater. DO NOT release the button after the third tap.
+
#Tap the Test button on a Main Repeater '''3''' times. '''DO NOT release the button after the third tap.'''
#Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately 3 seconds).
+
#Keep the Test button pressed on the third tap until all the LEDs start to flash red slowly (approximately '''3''' seconds).
#Release the Test button and immediately triple tap it again. All the LEDs will flash red quickly.
+
#Release the Test button and immediately tap '''3''' times again. All the LEDs will flash Red quickly.
 
#When the LEDs stop flashing, the Main Repeater has been returned to factory settings
 
#When the LEDs stop flashing, the Main Repeater has been returned to factory settings
  
Line 5,750: Line 5,835:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
*'''Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)'''
+
*'''Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 1st Generation (LRF2-xCRB-)'''
  
#Quickly triple tap and hold the Test, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
+
#Quickly tap '''3''' times and hold the Test, Lights ON, or Lights OFF button on the Sensor. '''DO NOT release after third tap'''.
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
#Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
+
#Release the button and tap it again '''3''' times until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
#The Sensor has now been returned to Factory Default Settings.
  
*'''Radio Powr SavrTM Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)'''
+
*'''Radio Powr Savr™ Occupancy/Vacancy Ceiling Sensor – 2nd Generation (LRF2- xCR2B-)'''
  
#Quickly triple tap and hold the Test or Light button on the Sensor. DO NOT release after third tap.
+
#Quickly tap '''3''' times and hold the Test or Light button on the Sensor. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
 
#Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second).
#Release the button and triple tap the button again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
+
#Release the button and tap '''3''' times again until the dome LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
#The Sensor has now been returned to Factory Default Settings.
  
*'''Radio Powr SavrTM Occupancy/Vacancy Wall-Mounted Sensor'''
+
*'''Radio Powr Savr™ Occupancy/Vacancy Wall-Mounted Sensor'''
  
#Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. DO NOT release after third tap.
+
#Quickly triple tap and hold the Sensor, Lights ON, or Lights OFF button on the Sensor. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
 
#Keep the button pressed after the third tap for a few seconds until the lens LED begins to flash slowly (approximately once per second).
#Release the button and triple tap the button again until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
+
#Release the button and tap it again '''3''' times until the lens LED on the Sensor flashes quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Sensor has now been returned to Factory Default Settings.
 
#The Sensor has now been returned to Factory Default Settings.
  
Line 5,795: Line 5,880:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly triple tap and hold down any button on the Main Repeater. DO NOT release after the third tap.
+
#Quickly tap '''3''' times and hold down any button on the Main Repeater. '''DO NOT release after the third tap.'''
#Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash red slowly (approximately once per second).
+
#Continue to hold the button for a few seconds. The Main Repeater LEDs will begin to flash Red slowly (approximately once per second).
#Release the button and quickly perform another triple tap of the button. The Main Repeater LEDs will flash green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
+
#Release the button and quickly tap '''3''' times again. The Main Repeater LEDs will flash Green rapidly and then will reset, turning off all LEDs and then flashing the LEDs and beeping once. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The Main Repeater and system components have now been returned to Factory Default Settings.
 
#The Main Repeater and system components have now been returned to Factory Default Settings.
  
Line 5,823: Line 5,908:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Quickly triple tap and hold any button (except Learn) on the VCRX. DO NOT release after third tap.
+
#Quickly tap '''3''' times and hold any button (except Learn) on the VCRX. '''DO NOT release after third tap.'''
 
#Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
 
#Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second).
#Release the button and triple tap the button again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
+
#Release the button and tap '''3''' times again until all the status LEDs on the VCRX flash quickly. (*Note* The time between release and the second triple tap must be less than half a second, thus must be performed very quickly).
 
#The VCRX has now been returned to Factory Default Settings.
 
#The VCRX has now been returned to Factory Default Settings.
  
Line 5,851: Line 5,936:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED flashs green rapidly.
+
#Tap the shade button quickly '''3''' times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
#Immediately tap the shade button quickly three more times, until the shade button LED flashs green rapidly, then flashs red/green three times, and turns off.
+
#Immediately tap the shade button quickly '''3''' more times, until the shade button LED flashes '''Green''' rapidly, then flashes '''Red/Green''' '''3''' times, and turns off.
 
#The Serena shade has now been returned to Factory Default Settings.
 
#The Serena shade has now been returned to Factory Default Settings.
  
Line 5,878: Line 5,963:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the shade button quickly 3 times, and hold the shade button after the third tap until the shade button LED flashs green rapidly.
+
#Tap the shade button quickly '''3''' times, and hold the shade button after the third tap until the shade button LED flashs Green rapidly.
#Immediately tap the shade button quickly three more times, until the shade button LED flashs '''Green''' rapidly, then flashs '''Red/Green''' three times, and turns off.
+
#Immediately tap the shade button quickly '''3''' more times, until the shade button LED flashes '''Green''' rapidly, then flashs '''Red/Green''' '''3''' times, and turns off.
 
#The Sivoia shade has now been returned to Factory Default Settings.
 
#The Sivoia shade has now been returned to Factory Default Settings.
  
Line 5,907: Line 5,992:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Triple tap the tapswitch on a control. DO NOT release after the third tap.
+
#Tap the tapswitch '''3''' times on a control. '''DO NOT release after the third tap.'''
#Keep the tapswitch pressed on the third tap (for approximately 3 seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
+
#Keep the tapswitch pressed on the third tap (for approximately '''3''' seconds) until the LEDs on the dimmer start to scroll up and down quickly, or the LED on the switch flashes quickly
#Release the tapswitch and immediately triple tap the tapswitch again.
+
#Release the tapswitch and immediately tap it '''3''' times again.
 
#The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
 
#The LEDs on the dimmer will scroll up and down slowly and then the LED on the switch will flash slowly, indicating it has now been returned to Factory Default Settings.
  
Line 5,937: Line 6,022:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Tap the "On" button quickly three times, holding on the last press.
+
#Tap the "On" button quickly '''3''' times, holding on the last press.
 
#Continue to hold the "On" button until the light begins to flash quickly.
 
#Continue to hold the "On" button until the light begins to flash quickly.
#Release the button, then immediately tap the button three more times.
+
#Release the button, then immediately tap the button '''3''' more times.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
 
#All paired Pico remote controls are removed and all settings are returned to factory default.
  
Line 5,972: Line 6,057:
 
#Rotate the knob to view settings and press the knob to confirm.
 
#Rotate the knob to view settings and press the knob to confirm.
 
#Once in the installer settings, rotate the knob to '''99'''.
 
#Once in the installer settings, rotate the knob to '''99'''.
#Press the knob to confirm, then press and hold the knob for 3 seconds.
+
#Press the knob to confirm, then press and hold the knob for '''3''' seconds.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,003: Line 6,088:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press 10 times of any button or exclude the device from Z-Wave network, then cut off the main power.
+
#Press '''10''' times of any button or exclude the device from Z-Wave network, then cut off the main power.
 
#The factory setting will be restored.
 
#The factory setting will be restored.
  
Line 6,010: Line 6,095:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press 3 times on "+" or "-" button to add the device. If successful, the green LED flashs 4 times.
+
#Press 3 times on "+" or "-" button to add the device. If successful, the green LED flashes '''4''' times.
#*Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
+
#*Note: If an external switch is wired to the dimmer, you may also toggle that '''3''' times to add the device to the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,018: Line 6,103:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED flashs 4 times.
+
#Press 3 times on "+" or "-" button to exclude the device from the network. If successful, the green LED flashes '''4''' times.
#*Note: If an external switch is wired to the dimmer, you may also toggle that 3 times to add the device to the network.
+
#*Note: If an external switch is wired to the dimmer, you may also toggle that '''3''' times to add the device to the network.
  
 
<hr />
 
<hr />
Line 6,039: Line 6,124:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#To reset the sensor, press and hold the Z-button for about 20 seconds.
+
#To reset the sensor, press and hold the Z-button for about '''20''' seconds.
 
#The LED will change from steadily illuminated to flashing then back to steadily illuminated, indicating that the reset operation was successful.
 
#The LED will change from steadily illuminated to flashing then back to steadily illuminated, indicating that the reset operation was successful.
  
Line 6,046: Line 6,131:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Rapidly press the Z-button 3 times to include the device in the network.
+
#Rapidly press the Z-button '''3''' times to include the device in the network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,053: Line 6,138:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Rapidly press the Z-button 3 times to exclude the device from the network.
+
#Rapidly press the Z-button '''3''' times to exclude the device from the network.
  
 
<hr />
 
<hr />
Line 6,073: Line 6,158:
  
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Ensure that the smart plug is inserted into an AC outlet.
#Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device, returning the device to a factory state.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,079: Line 6,164:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to include the device in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,086: Line 6,171:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,106: Line 6,191:
  
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Ensure that the smart plug is inserted into an AC outlet.
#Press and hold the program button on the front for about 1 second to exclude the device, returning the device to a factory state.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device, returning the device to a factory state.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,112: Line 6,197:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the program button on the front for about 1 second to include the device in the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to include the device in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,119: Line 6,204:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,140: Line 6,225:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
+
#Press and hold the Z-button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,146: Line 6,231:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for 2 seconds then disappear.
+
#Press the Z-button on your sensor. If your sensor has been successfully linked to your network, its LED will turn solid for '''2''' seconds and then turn off.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
 
#If linking was unsuccessful, the LED will continue to flash if you tap its button.
  
Line 6,175: Line 6,260:
  
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Ensure that the smart plug is inserted into an AC outlet.
#Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device and return it to a factory state.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,181: Line 6,266:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,188: Line 6,273:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,208: Line 6,293:
  
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Ensure that the smart plug is inserted into an AC outlet.
#Press and hold the program button on the front for about 1 second to exclude the device and return it to a factory state.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device and return it to a factory state.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,214: Line 6,299:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Press and hold the program button on the front for about 1 second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to include the device. The LED will stop flashing and glow steading to indicate the device has joined the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,221: Line 6,306:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Press and hold the program button on the front for about 1 second to exclude the device from the Z-Wave network.
+
#Press and hold the program button on the front for about '''1''' second to exclude the device from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,242: Line 6,327:
 
'''Factory Reset'''
 
'''Factory Reset'''
  
#Press and hold the Z-button for 20 seconds and then release it. Your sensor will now be reset to its original settings
+
#Press and hold the Z-button for '''20''' seconds and then release it. Your sensor will now be reset to its original settings
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,248: Line 6,333:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#If the plug-in has not already been included into a Z-Wave network, the LED indicator will flash rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can jooin the Hubitat Elevation™ Z-Wave network.
+
#If the plug-in has not already been included into a Z-Wave network, the LED indicator will flash rapidly. Otherwise, the plug-in has already been included and must first be excluded before it can join the Hubitat Elevation™ Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,255: Line 6,340:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Triple-click the Z-Button. The plug-in will be removed from your Z-Wave network.
+
#Click the Z-Button '''3''' times. The plug-in will be removed from your Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,281: Line 6,366:
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#Momentarily press the '''Program Switch'''
 
#Momentarily press the '''Program Switch'''
#The LED should flash 5 times indicating the sensor has not yet been included in the Z-Wave network.
+
#The LED should flash '''5''' times indicating the sensor has not yet been included in the Z-Wave network.
#If the LED flashs only 1 time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
+
#If the LED flashes only '''1''' time, then it has already been included in a Z-Wave network and must first be excluded before it my join the Hubitat Elevation™ Z-Wave network.
#Momentarily press the button again after it flashs 5 times, to automatically include the sensor in the Z-Wave network.
+
#Momentarily press the button again after it flashes '''5''' times, to automatically include the sensor in the Z-Wave network.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,310: Line 6,395:
  
 
#Ensure that the smart plug is inserted into an AC outlet.
 
#Ensure that the smart plug is inserted into an AC outlet.
#Press and hold the Z-Button on the smart plug for more than 20 seconds.
+
#Press and hold the Z-Button on the smart plug for more than '''20''' seconds.
#The LED indicator will illuminate yellow steadily for about 2 seconds.
+
#The LED indicator will illuminate Yellow steadily for about '''2''' seconds.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,317: Line 6,402:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Rapidly press the Z-button 3 times to include the device in the network.
+
#Rapidly press the Z-button '''3''' times to include the device in the network.
  
 
'''Testing the Smart Plug Z-Wave connection'''
 
'''Testing the Smart Plug Z-Wave connection'''
Line 6,323: Line 6,408:
 
You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.
 
You can test the connectivity of the Z-Wave® network connection, with the RGB LED being used to indicate the connection quality.
  
To begin testing, press and hold the Z button for 6-9 seconds, releasing the button when the RGB LED illuminates violet.
+
To begin testing, press and hold the Z button for '''6-9''' seconds, releasing the button when the RGB LED illuminates violet.
  
 
*'''''Note'':''' The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
 
*'''''Note'':''' The smart plug must be included into a Z-Wave network to test the network connection. You can abort the test at any time by pressing the Z button.
**'''flashing Green''': The RGB LED will flash green while the smart plug is attempting to establish a connection with the main controller.
+
**'''Flashing Green''': The RGB LED will flash Green while the smart plug is attempting to establish a connection with the main controller.
**'''Solid Green''': The RGB LED will illuminate green for about 2 seconds to indicate that direct communications are stable.
+
**'''Solid Green''': The RGB LED will illuminate Green for about '''2''' seconds to indicate that direct communications are stable.
**'''flashing Orange''': The RGB LED will flash orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
+
**'''Flashing Orange''': The RGB LED will flash Orange while the smart plug is attempting to establish a connection with the main controller with intermediate radio transmitting power.
**'''Solid Orange''': The RGB LED will illuminate orange for about 2 seconds to indicate that the communication quality is moderate.
+
**'''Solid Orange''': The RGB LED will illuminate Orange for about '''2''' seconds to indicate that the communication quality is moderate.
**'''Solid Red''': The RGB LED will illuminate red for about 2 seconds to indicate that they communications attempt has failed.
+
**'''Solid Red''': The RGB LED will illuminate Red for about '''2''' seconds to indicate that they communications attempt has failed.
  
 
'''Exclusion from the Z-Wave Network'''
 
'''Exclusion from the Z-Wave Network'''
Line 6,337: Line 6,422:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Rapidly press the Z-button 3 times to exclude the device from the network.
+
#Rapidly press the Z-button '''3''' times to exclude the device from the network.
#The RGB LED will flash orange while the smart plug is being removed.
+
#The RGB LED will flash Orange while the smart plug is being removed.
#The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate orange steadily for about 2 seconds.
+
#The smart plug will be removed from your Z-Wave network and the RGB LED will then illuminate Orange steadily for about '''2''' seconds.
  
 
<hr />
 
<hr />
Line 6,361: Line 6,446:
 
#Remove the cover of contact sensor main body.
 
#Remove the cover of contact sensor main body.
 
#Make sure the sensor is connected to power source.
 
#Make sure the sensor is connected to power source.
#Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
+
#Press and hold the reset button for '''10''' seconds, the LED light will flash Red once.
 
#Release the button.
 
#Release the button.
  
Line 6,368: Line 6,453:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The contact sensor will be detected and included in the Z-Wave network.
 
#The contact sensor will be detected and included in the Z-Wave network.
  
Line 6,376: Line 6,461:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,397: Line 6,482:
 
#Remove the cover of contact sensor main body.
 
#Remove the cover of contact sensor main body.
 
#Make sure the sensor is connected to power source.
 
#Make sure the sensor is connected to power source.
#Press and hold the reset button for 10 seconds, the LED light will flash red for 1 time.
+
#Press and hold the reset button for '''10''' seconds, the LED light will flash Red once.
 
#Release the button.
 
#Release the button.
  
Line 6,404: Line 6,489:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The contact sensor will be detected and included in the Z-Wave network.
 
#The contact sensor will be detected and included in the Z-Wave network.
  
Line 6,412: Line 6,497:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,433: Line 6,518:
 
#Remove the sensor’s cover.
 
#Remove the sensor’s cover.
 
#Make sure the sensor is connected to power source.
 
#Make sure the sensor is connected to power source.
#Press the code button for '''10 seconds''', the LED will flash red for '''1 time'''.
+
#Press the code button for '''10''' seconds, the LED will flash Red once.
 
#Release the code button.
 
#Release the code button.
 
#*'''NOTE:''' When the PIR is being restored to factory settings, please make sure a power source is connected.
 
#*'''NOTE:''' When the PIR is being restored to factory settings, please make sure a power source is connected.
Line 6,441: Line 6,526:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The motion sensor will be detected and included in the Z-Wave network.
 
#The motion sensor will be detected and included in the Z-Wave network.
  
Line 6,449: Line 6,534:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the sensor will be excluded from the Z-Wave network.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times and the sensor will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,468: Line 6,553:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the code button on the front of the outlet for 10 seconds.
+
#Press and hold the code button on the front of the outlet for '''10''' seconds.
 
#When the LED flashes, release the button.
 
#When the LED flashes, release the button.
#When the outlet has been reset, the LED will flash on and off '''5 times''' within a 2 second period.
+
#When the outlet has been reset, the LED will flash on and off '''5''' times within a '''2''' second period.
  
 
'''Join the Z-Wave Network'''
 
'''Join the Z-Wave Network'''
Line 6,476: Line 6,561:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times'''.
+
#Quickly click the code button '''3''' times, the LED light will flash '''5''' times.
 
#The device will be detected and included in the Z-Wave network.
 
#The device will be detected and included in the Z-Wave network.
  
Line 6,484: Line 6,569:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the code button, the LED light will flash for '''5 times''' and the device will be excluded from the Z-Wave network.
+
#Quickly click the code button '''3''' times, the LED light will flash for '''5''' times and the device will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,503: Line 6,588:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the code button for 10 seconds.
+
#Press and hold the code button for '''10''' seconds.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
  
Line 6,510: Line 6,595:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the red SOS alarm button.
+
#Quickly click the Red SOS alarm button '''3''' times.
 
#The device will be detected and included in the Z-Wave network.
 
#The device will be detected and included in the Z-Wave network.
  
Line 6,518: Line 6,603:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the red SOS alarm button and the device will be excluded from the Z-Wave network.
+
#Quickly click the Red SOS alarm button '''3''' times and the device will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,537: Line 6,622:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#Press and hold the code button for 10 seconds.
+
#Press and hold the code button for '''10''' seconds.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
 
#Release the Code button.  '''Note:''' Do not power off during factory reset.
  
Line 6,544: Line 6,629:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Quickly, '''triple-click''' the red SOS alarm button.
+
#Quickly click the Red SOS alarm button '''3''' times.
 
#The device will be detected and included in the Z-Wave network.
 
#The device will be detected and included in the Z-Wave network.
  
Line 6,552: Line 6,637:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Quickly, '''triple-click''' the red SOS alarm button and the device will be excluded from the Z-Wave network.
+
#Quickly click the Red SOS alarm button '''3''' times and the device will be excluded from the Z-Wave network.
  
 
<hr />
 
<hr />
Line 6,572: Line 6,657:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#A simultaneous long press (1sec) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
+
#A simultaneous long press ('''1''' second) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
  
Line 6,579: Line 6,664:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
+
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#The LED glows in '''pink''' to confirm the selection
#Push on the '''solid circle''' within 10 seconds.
+
#Push on the '''solid circle''' within '''10''' seconds.
#The LED flashs in '''pink''' to confirm your choice and then flashs in '''green''' to confirm the procedure.
+
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure.
 
#The device will be detected and included in the Z-Wave network.
 
#The device will be detected and included in the Z-Wave network.
  
Line 6,590: Line 6,675:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
+
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#The LED glows in '''pink''' to confirm the selection
#Push on the '''solid circle''' within 10 seconds.
+
#Push on the '''solid circle''' within '''10''' seconds.
#The LED flashs in '''pink''' to confirm your choice and then flashs in '''green''' to confirm the procedure
+
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 6,613: Line 6,698:
 
|}'''Factory Reset'''
 
|}'''Factory Reset'''
  
#A simultaneous long press (1sec) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
+
#A simultaneous long press ('''1''' second) on '''O''' and '''<big>–</big>'''  will perform this factory reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
 
#The LED will flash '''red''' and '''green''' to validate the reset.
  
Line 6,620: Line 6,705:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Inclusion''' on the '''Device Discovery''' page.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
 
#*See [https://docs.hubitat.com/Discovering%20your%20Devices Discovering your devices] for detail instructions.
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
+
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#The LED glows in '''pink''' to confirm the selection
#Push on the '''solid circle''' within 10 seconds.
+
#Push on the '''solid circle''' within '''10''' seconds.
#The LED flashs in '''pink''' to confirm your choice and then flashs in '''green''' to confirm the procedure.
+
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure.
 
#The device will be detected and included in the Z-Wave network.
 
#The device will be detected and included in the Z-Wave network.
  
Line 6,631: Line 6,716:
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#From the Hubitat Web Interface home page, select '''Z-Wave''', then '''Start Z-Wave Exclusion''' on the '''Device Discovery''' page.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
 
#*See [[Discovering your Devices|Discovering your devices]] for detail instructions.
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for 1sec.
+
#Simultaneously push on the '''solid circle''' and the '''<big>+</big>''' for '''1''' second.
 
#The LED glows in '''pink''' to confirm the selection
 
#The LED glows in '''pink''' to confirm the selection
#Push on the '''solid circle''' within 10 seconds.
+
#Push on the '''solid circle''' within '''10''' seconds.
#The LED flashs in '''pink''' to confirm your choice and then flashs in '''green''' to confirm the procedure
+
#The LED flashes in '''pink''' to confirm your choice and then flashes in '''green''' to confirm the procedure
 
#The device will be excluded from the Z-Wave network.
 
#The device will be excluded from the Z-Wave network.
  
Line 6,658: Line 6,743:
 
#Inside the battery compartment at the top, is a small button.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,668: Line 6,753:
 
#Inside the battery compartment at the top, is a small button.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Press the button 4 times to join the device to the Zigbee network.
+
#Press the button '''4''' times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
+
#*'''3''' Green flashes indicate the device has successfully joined the network.
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from '''step 4'''.
+
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,683: Line 6,768:
 
#Inside the battery compartment at the top, is a small button.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
<hr />
 
<hr />
Line 6,706: Line 6,791:
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,716: Line 6,801:
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Press the button 4 times to join the device to the Zigbee network.
+
#Press the button '''4''' times to join the device to the Zigbee network.
 
#The LED will flash in the following sequences:
 
#The LED will flash in the following sequences:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
+
#*'''3''' Green flashes indicate the device has successfully joined the network.
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from '''step 4'''.
+
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,731: Line 6,816:
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#Inside the battery compartment is a small button on the side of the circuit board.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
<hr />
 
<hr />
Line 6,754: Line 6,839:
 
#Inside the battery compartment at the top, is a small button.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,768: Line 6,853:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
+
#*'''3''' Green flashes indicate the device has successfully joined the network.
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens,  ensure a factory reset has been performed, and repeat the process from '''step 4'''.
+
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens,  ensure a factory reset has been performed and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,779: Line 6,864:
 
#Inside the battery compartment at the top, is a small button.
 
#Inside the battery compartment at the top, is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
<hr />
 
<hr />
Line 6,802: Line 6,887:
 
#Inside the battery compartment is a small button.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,816: Line 6,901:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
+
#*'''3''' Green flashes indicate the device has successfully joined the network.
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from '''step 4'''.
+
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed, and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,827: Line 6,912:
 
#Inside the battery compartment is a small button.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
<hr />
 
<hr />
Line 6,850: Line 6,935:
 
#Inside the battery compartment is a small button.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,864: Line 6,949:
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Red - Yellow''' flashes indicate it is searching for a network to join.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
 
#*'''Yellow - Green - Yellow''' flashes indicate the device is being configured.
#*'''3 Green''' flashes indicate the device has sucessfully joined the network.
+
#*'''3''' Green flashes indicate the device has successfully joined the network.
#*'''3 Red''' flashes indicate the devices failed to join the network. If htis happens, ensure a factory reset has been performed, and repeat the process from '''step 4'''.
+
#*'''3''' Red flashes indicate the devices failed to join the network. If this happens, ensure a factory reset has been performed, and repeat the process from step 4.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,875: Line 6,960:
 
#Inside the battery compartment is a small button.
 
#Inside the battery compartment is a small button.
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
 
#*'''Note:''' ''The button may be pressed with the end of a paper clip or a pencil. Do not use a sharp object like a tack or pin.''
#Pressing the button 10 times will leave the network and reset the device to factory defaults.
+
#Pressing the button '''10''' times will leave the network and reset the device to factory defaults.
#The LED will flash '''Red 3 times''' to indicate is has left the network (If joined), and it will flash '''Green 5 times''' to indicate defaults have been restored.
+
#The LED will flash Red '''3''' times to indicate is has left the network (If joined), and it will flash Green '''5''' times to indicate defaults have been restored.
  
 
<hr />
 
<hr />
Line 6,897: Line 6,982:
  
 
#Insert two AA alkaline batteries and re-insert the tray.
 
#Insert two AA alkaline batteries and re-insert the tray.
#Press the RESET button '''5 times''' in rapid secession.
+
#Press the RESET button '''5''' times in rapid secession.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,908: Line 6,993:
 
#Turn the dial to '''AUTO'''.
 
#Turn the dial to '''AUTO'''.
 
#When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
 
#When batteries are inserted, the timer will automatically attempt to connect and the wireless icon on screen will begin to flash.
#*'''NOTE:''' The timer will remain in pairing mode for '''10 minutes or until paired.''' If pairing is not successful after 10 minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button 5 times in rapid secession.
+
#*'''NOTE:''' The timer will remain in pairing mode for '''10''' minutes or until paired'''.''' If pairing is not successful after '''10''' minutes, the timer will stop trying to pair. To enter pairing mode again press the RESET button '''5''' times in rapid secession.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Watch the status in the device details page to confirm proper operation.
 
#Watch the status in the device details page to confirm proper operation.
Line 6,915: Line 7,000:
  
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
 
#From the device's details page, select '''Remove Device''', then '''Remove'''
#Press the RESET button '''5 times''' in rapid secession.
+
#Press the RESET button '''5''' times in rapid secession.
  
 
<hr />
 
<hr />
Line 6,935: Line 7,020:
  
 
#Ensure the controller is connected to power.
 
#Ensure the controller is connected to power.
#Press the SYNC button '''5 times''' in rapid secession.
+
#Press the SYNC button '''5''' times in rapid secession.
  
 
'''Join the Zigbee Network'''
 
'''Join the Zigbee Network'''
Line 6,944: Line 7,029:
 
#Turn the dial to '''AUTO'''.
 
#Turn the dial to '''AUTO'''.
 
#When the controller is first connected to power, it will automatically attempt to connect.  
 
#When the controller is first connected to power, it will automatically attempt to connect.  
#*'''NOTE:''' If pairing is not successful after 10 minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button '''5 times''' in rapid succession
+
#*'''NOTE:''' If pairing is not successful after '''10''' minutes, the controller will stop trying to pair. To re-enter pairing mode, push the 'SYNC' button '''5''' times in rapid succession
 
#The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words '''SMART MODE''' will appear on the screen.
 
#The wireless icon will flash until the controller is paired. Once paired, the wireless icon will remain solid, and the words '''SMART MODE''' will appear on the screen.
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
 
#Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevation™
Line 6,951: Line 7,036:
 
'''Leaving the Zigbee Netwo'''<nowiki/>'''rk'''
 
'''Leaving the Zigbee Netwo'''<nowiki/>'''rk'''
  
#From the device's detail<nowiki/>s page, select Remove Device, then Remove
+
# From the device's detail<nowiki/>s page, select '''Remove Device''', then '''Remove'''.
#Press the SYNC button 5 <nowiki/>times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for 5 seconds to cancel re-pairing.
+
# Press the RESET button '''5'''<nowiki/> times in rapid secession. The device will try to re-connect again, so you will need to let it time out or hold the SYNC button for '''5''' seconds to cancel re-pairing.
 +
<hr />
  
<hr />
+
== '''<big>Orvibo</big>''' ==
  
=='''<big>Orvibo</big>'''==
 
 
{| class="wikitable sortable"
 
{| class="wikitable sortable"
 
|<div style="text-align: center;">Brand</div>
 
|<div style="text-align: center;">Brand</div>

Revision as of 16:44, 8 October 2019

Before you can join your devices to your Hubitat Elevation™ hub, you must first remove them from the previous hub or bridge. While Zigbee devices can simply be removed and put into Paring Mode using the manufacturer's instructions, Z-Wave devices must be Excluded from their previous network before joining a new one. Exclusion will happen automatically when the device is removed from Hubitat Elevation™, however it is recommend that Z-Wave devices always be factory reset as well. If a device cannot be factory reset, or is in an unknown state, then it is recommended to do a General Exclusion in your Hubitat Elevation™ hub to be sure it isn't joined to the former Z-Wave mesh. Typically the same button on the device for inclusion is also used for exclusion. If Hubitat doesn't show Unknown Device Excluded in the log, then the General Exclusion has failed and the device probably won't be able to be joined. See How to Build a Solid Z-Wave Mesh for further detail on methods of Exclusion.

ADT

Brand
Device
Product Number
Device Type
Protocol
ADT (Nortek)
Water Leak Detector
10016864C
Water Sensor
Zigbee

Factory Reset

  1. Remove the cover by rotating it counterclockwise
  2. Press and hold the Connect button for 5 seconds
  3. After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. Remove the cover by rotating it counterclockwise
  2. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  3. Press and hold the Connect button for 5 seconds
  4. After the button is released, the LED will flash quickly for a few seconds, go dark for a few seconds, then flash slowly to indicate it is in pairing mode

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

AduroSmart

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Door / Window Sensor
ERIA 81822
Contact Sensor
Zigbee

Factory Reset

  1. Use the provided pin to press and hold the reset button for 10 seconds.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Use the provided pin to press and hold the reset button for 10 seconds.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Dimmer Switch
ERIA 81825
Button Controller
Zigbee

Factory Reset

  1. Hold down the two middle buttons until the light flashes green. A red flash indicates an unsuccessful reset.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Hold down the off (circle) button for 10 seconds until it flashes green 3 times.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
AduroSmart
Motion Sensor
ERIA 81823
Motion Sensor
Zigbee

Factory Reset

  1. Use the provided pin to press and hold the reset button for 10 seconds.
    • Battery powered Zigbee devices often pair easier when their batteries are removed for 10 seconds following a factory reset.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Use the provided pin to press and hold the reset button for 10 seconds.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Aeotec (Aeon Labs)

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Doorbell Gen5
ZW056
Doorbell
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Doorbell will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Doorbell Gen5, and its LED will flash rapidly to indicate that it is communicating.
  3. If your Doorbell has been successfully linked to your network, its LED will become solid for 2 seconds, then stop. If linking was unsuccessful, the LED will flash when you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Doorbell.
  4. If your Doorbell has been successfully unlinked to your network, its LED will begin to flash slowly indicating it is ready to be paired to a new network.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Doorbell 6
ZW162-A
Doorbell
Z-Wave Plus

Factory Reset

  1. Press and hold the Action button for 20 seconds
  2. Within 2-5 seconds, the test doobell sound will run, then stop after 5 seconds has elapsed.
  3. From 5-10 seconds, the LED will begin to flash faster and faster still from 10-20 seconds.
  4. After 21 seconds, the LED will quickly flash 3 times, and then the LED slowly pulse up and down as you hold down the Action Button.
  5. With the LED pulsing, release the Action button, and the Doorbell 6 will be reset to factory defaults.

Join the Z-Wave Network

  1. Power Doorbell 6 through the provided power adapter.
  2. Ensure that Doorbell 6 LED is flashing slowly.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  4. Tap the Doorbell 6 Action Button once.
  5. If Doorbell 6 has successfully paired to your Z-Wave gateway, the LED will be a solid color for 30 seconds, then turn off.
  6. If is fails to join the Z-Wave network, the LED will flash slowly.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button 6 times in 2 seconds.
  4. If your Doorbell 6 has been successfully unpaired from the Z-Wave network, its LED will begin to flash slowly, indicating it is ready to join a Z-Wave network again.
Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor 6
ZW112
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold Door Window Sensor 6 Action button
  2. Wait until the RGB LED turns into a Green Color, and then release. (LED will change from Yellow, Purple, Red, then to Green)
  3. If your MultiSensor has been successfully factory reset from its previous network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Tap the button on the Door Window Sensor 6
  3. The LED will flash green to indicate successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your Door Window Sensor is successfully removed from the Z-Wave network, the RGB LED will become a colorful gradient for a few seconds and then turn off. If the removing was unsuccessful, the RGB LED will be solid for 8 seconds and then turn off, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor Gen5
ZW120
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once to include the door/window sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your Door Window Sensor has been successfully removed from your Z-Wave network, its Status LED will fast flash for 8 seconds and then slow flash for 3 seconds when you press the Action Button again.
  5. If the removal was unsuccessful, the Status LED will fast flash for 2 seconds and then be solid for 2 seconds when you press the Action Button, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor Gen2
DSB29
Contact Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once to include the door/window sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor to exclude it from the network

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Door/Window Sensor 1E
DSB04100
Contact Sensor
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the sensor to a default state.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the security tamper switch located at the back of the Aeon Labs Door/Window Sensor to include it in the network
  3. The sensor will now stay awake for 10 minutes to receive network instructions. The LED on the will be flashing while awake.
    • Note: The DSB04100 sensor can only be taught to communicate to devices within its own network.
    • If the Aeon Labs Door / Window Sensor was not included in a Z-Wave network, pressing the security switch will illuminate the LED solid red on the front of the sensor for 5 seconds.
    • If the sensor was successfully included in the Z-Wave network, the LED will flash instead of staying solid.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Use an Aeon Z-Stick or Minimote to exclude the sensor from previous networks

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Garage Door Controller Gen5
ZW062
Garage Door Opener
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds and release.
  2. Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow flashing to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Z-Wave Button on the Garage Door Controller.
  3. The LED on Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 second for a successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on the Garage Door Controller.
  4. The LED on Garage Door Controller will flash rapidly, followed by a solid LED for 1-2 second for a successful exclusion.
  5. The Network LED on the Garage Door Controller should now be flashing slowly to indicate it is ready to be paired to a new network.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Dry Contact Sensor Gen5
ZW097
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds and Status LED will be solid for 2 seconds to confirm a success.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Sensor.
  3. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds, then disappear.
  4. If linking was unsuccessful, the LED will continue to flash if you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor.
  4. If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
  5. If unlinking was not successful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Aeon Labs Home Energy Meter
AEDSB09104ZWUS
Energy Meter
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 10 seconds.
  2. If successful, the LED on the HEM should begin to flash slowly.

Join the Z-Wave Network

  1. Remove the screw from the back of your Reader and open the battery cover.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully linked to your network, its light will remain solid for 1 second. If the linking was unsuccessful the light will flash after pressing your meter’s Action Button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. Remove the screw from the back of your Reader and open the battery cover.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. Press the Action Button (small black button under the battery tray) on your reader. If your Reader has been successfully removed from your network, its light will flash for 1 second.
  5. If the removal was unsuccessful the light will be solid after pressing your meter’s Action Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Home Energy Meter Gen2 / Gen5
ZW095
Energy Meter
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 10 seconds.
  2. If successful, the LED on the HEM should begin to flash slowly.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. Press the Action Button on your HEM. If it has been successfully linked to your  network, its LED will remain illuminated. If the linking was unsuccessful, your HEM’s LED will continue to flash.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your HEM. If it has been successfully removed from your  network, its LED will flash. If the removal was unsuccessful, its LED will be solid and it will be then repeated again.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb Gen5
ZW098
Bulb
Z-Wave Plus

Factory Reset

  1. Removing LED Bulb from your Z-Wave network will reset LED Bulb to default factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, wait 2 seconds. Now toggle your wall switch ON. LED Bulb’s green LED will flash to indicate that it is looking for a Z-Wave network to connect to.
  3. After successfully connecting to your network, LED Bulb will illuminate. If a network connection has failed, it will remain without light.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Turn LED Bulb’s wall switch on.
  4. Toggle LED Bulb’s wall switch off, on, off, on, off, on within 2 seconds. The LED should flash orange, and if successful, the orange LED will be solid for 2 seconds before becoming a white color. LED Bulb should now be removed from your Z-Wave network.
  5. To confirm successful removal its color will change to orange for 2 seconds before changing to white. If removal was unsuccessful, LED Bulb will flash orange for 3 seconds before changing to red for 2 seconds.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb 6 Multi-Color
ZWA002
Bulb
Z-Wave Plus

Factory Reset

  1. Turn LED Bulb’s wall switch on and wait 1 second.
  2. Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
  3. If successful, the LED Bulb 6 Multi-Color will change to a warm white, solid yellow, then flash red -> white 3 times to indicate a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will turn into a solid yellow color to indicate that it is in pair mode up to 10 seconds.
  3. After successfully connecting to your network, LED Bulb will flash green -> white color for 3 seconds. If a network connection has failed, LED Bulb 6 Multi-Color will flash red -> white for 3 seconds.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
  4. LED Bulb 6 has been unpaired successfully, the LED will flash blue > white for 3 seconds.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
LED Bulb 6 Multi-White
ZWA001
Bulb
Z-Wave Plus

Factory Reset

  1. Turn LED Bulb’s wall switch on and wait 1 second.
  2. Toggle LED Bulb's wall switch 6 times (off -> on, off -> on, off -> on, off -> on, off -> on, off -> on) between 0.5 - 2 seconds per re-power.
  3. If successful, the LED Bulb 6 Multi-White will flash twice to indicate that it successfully reset itself to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  2. With LED Bulb in its fitting, toggle your wall switch ON. LED Bulb’s LED will flash 2 times to indicate that it is looking for a Z-Wave network to connect to.
  3. After successfully connecting to your network, LED Bulb will flash off then on in about 0.5 second to indicate that it attempted to pair to your network. If a network connection has failed, LED Bulb 6 Multi-White will not react.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Turn LED Bulb’s wall switch on and wait 1 second.
  4. Toggle LED Bulb’s wall switch 3 times (off > on, off > on, off > on) between 0.5 - 2 seconds per cycle.
  5. LED Bulb 6 if successful will flash once, dim to 5% for 5 seconds, then increase to 100% dim level to indicate a successful unpair and factory reset.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Illuminator G2
DSC19103-ZWUS
Dimmer
Z-Wave

Factory Reset

  1. Hold the Z-Wave button for 30 seconds and release it to reset the entire module including Z‐Wave to factory default settings (the LED will stay solid after holding the button for 30 seconds).

Join the Z-Wave Network

  1. Connect Micro Smart Dimmer to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Press the Z‐Wave button.
  4. If the inclusion fails, please repeat the process from step 2.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z‐Wave button.
  4. If the exclusion fails, please repeat the process from step 2

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Motor Controller
DSC14104-ZWEU/US, DSC14103-ZWAU
Motor Controller
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the controller to a default state.

Join the Z-Wave Network (Z-Stick)

  1. Connect Micro Motor Controller to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. Press the Action Button on your Micro Motor Controller.
  5. If Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
  6. If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
  7. Press the Action Button on the Z-Stick to take it out of installation mode.

Join the Z-Wave Network (Minimote)

  1. Connect Micro Motor Controller to an AC‐input power source.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Press the Include button on your Minimote.
  4. Press the Action Button on your Micro Motor Controller.
  5. If the Micro Motor Controller has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
  6. If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
  7. Press any button on your Minimote to take it out of inclusion mode.

Exclusion from the Z-Wave Network (Z-Stick)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. Press the Action Button on your Micro Motor Controller.
  5. If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
  6. If the removal was unsuccessful, the Network LED will not flash.
  7. Press the Action Button on the Z-Stick to take it out of removal mode.

Exclusion from the Z-Wave Network (Minimote)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Remove Button on your Minimote.
  4. Press the Action Button on your Micro Motor Controller.
  5. If your Micro Motor Controller has been successfully removed from your network, its Network LED will flash.
  6. If the removal was unsuccessful, the Network LED will not flash.
  7. Press any button on your Minimote to take it out of removal mode.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Micro Switch G2
DSC26 / DCS18
Switch
Z-Wave

Factory Reset

  1. Press and hold the button on the Micro Switch G2 for 20 seconds and then release it.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
  3. If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. If the Micro Switch G2 is installed for use with a light, the switch can be toggled to initiate pairing into the Z-Wave network (switch 6 times (ON to OFF or OFF to ON).
  4. If the Micro Switch G2 is uninstalled, the internal button can be pushed to initiate pairing into the Z-Wave network, but only if Micro is not already connected to an external switch.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Minimote
DSA03202
Button Controller
Z-Wave

Factory Reset

  1. Pull down the panel on the  Minimote
  2. Press and hold the bottom 2 buttons down. The Red and Blue LED will alternate faster and faster.
  3. When both Red and Blue LED become solid, you may let go.

Include a device from the Z-Wave Network

  1. Tap the Inclusion (+) button, LED should be flashing blue
  2. Tap the button on the device you want to add
  3. After the LED stops flashing rapidly, tap any button to get out of inclusion mode

Exclusion a device from the Z-Wave Network

  1. Tap the Exclusion (-) button, LED should flash red
  2. Tap button on the device you want to remove
  3. After LED stops flashing rapidly, tap any button to get out of the exclusion mode

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Multisensor Gen5
ZW074
Motion Sensor
Z-Wave

Factory Reset

  1. Press and hold Multisensor Gen5 Action button (For 20 seconds)
  2. The LED of the Multisensor Gen5 will flash faster and faster. At 20 seconds, the LED should become solid for 1-2 seconds to confirm factory reset.
  3. Release the Multisensor Gen5 Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Z-Wave Button on your MultiSensor.
  3. You can test if your MultiSensor has been successfully synced with your Z-Wave network by pressing its Z-Wave Button. If you press the button and your sensor’s LED illuminates for a few seconds, then syncing has been successful.
  4. If the LED flashes when the button is pressed, the syncing has been unsuccessful and you should repeat the above steps.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on your MultiSensor.
  4. If your MultiSensor has been successfully removed from your network, its LED will flash when you press the Z-wave Button.
  5. If the removal was unsuccessful, the LED will stay solid for a few seconds when you press the Z-wave Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Multisensor 6
ZW100
Motion Sensor
Z-Wave Plus

Factory Reset

  1. Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
  2. If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash.
  3. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your MultiSensor. The LED on Multisensor will flash Green rapidly, followed by a solid Green LED for 1 second for a successful inclusion, or a solid red LED for 1 second for a failed inclusion.
  3. You can test if your MultiSensor has been successfully included into your Z-Wave network by pressing its Action Button. If you press the button and your sensor's green LED is solid for a few seconds, then inclusion has been successful.
  4. If the green LED flashes when the button is pressed, the inclusion has been unsuccessful and you should repeat the steps from step 1.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your MultiSensor. The LED on Multisensor will flash red then change into a colorful gradient.
  4. If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colorful gradient for 3 seconds. When you press the Action Button on MultiSensor, its green LED will flash.
  5. If the removal was unsuccessful, the green LED will stay solid for a few seconds when you press the Action Button.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
NanoMote One
ZWA004
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the NanoMote button for 20 seconds.
  2. The LED will change from: Orange > Green > Red > Pink > Red
  3. Release the button on the second Red LED status. It will remain Red for 2 seconds
  4. Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Double click the NanoMote button, the LED will flash rapidly with a white color.
  3. If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
  4. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
    • If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Double click the NanoMote button, the LED will become a solid green color.
  4. If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
NanoMote Quad
ZWA003
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the NanoMote button for 20 seconds.
  2. The LED will change from: Orange > Green > Red > Pink > Red
  3. Release the button on the second Red LED status. It will remain Red for 2 seconds
  4. Tap button again while second Red LED is illuminated (you'll have 2 seconds to do so).

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Double click the NanoMote button (can be any button), the LED will flash rapidly with a white color.
  3. If your NanoMote has been successfully added to your Z-Wave  network, its white LED will be solid for about 10 seconds, then flash green to indicate it is awake.
  4. If the adding was unsuccessful and the red LED will be solid for 2 seconds and then off, repeat the above steps.
    • If your NanoMote does not go to sleep on its own, press and hold for 2 seconds (or until LED turns orange) then release its button to put your NanoMote to sleep.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Double click the NanoMote button, the LED will become a solid green color.
  4. If your NanoMote has been removed from your Z-Wave network, its LED will begin cycling through a rainbow of colors.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Dimmer
ZW111
Dimmer
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on the Nano Dimmer, the green LED (basic secure indication) will flash to indicate the Nano Dimmer is entering into pairing mode.
  3. If the Nano Dimmer has been successfully added to your Z-Wave network, its RGB LED will be solid.
  4. If the pairing was unsuccessful, the red LED will be on for 2 seconds and then remain a colorful gradient, repeat the steps above.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Switch (with energy reading)
ZW116
Switch
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once on the Nano Switch.
  3. If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Nano Switch (without energy reading)
ZW139
Switch
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it.
  2. Your Nano Switch will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once on the Nano Switch.
  3. If inclusion is successful, the green LED will be on for 2 seconds, and then return to a solid indication. If inclusion is unsuccessful, the red LED will be on for 2 seconds and then return to a colorful gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on the Nano Switch once or toggle the external manual switch 3 times in fast succession.
  4. If the Nano Switch has been successfully removed from your Z-Wave network, its RGB LED will remain colorful gradient. If the removal was unsuccessful, the RGB LED will still be solid (following the state of the output load).

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Range Extender (Aeon Labs Z-Wave Network Repeater)
DSD37
Switch
Z-Wave

Factory Reset

  1. Use an Aeon Z-Stick or Minimote to return the Range Extender to a default state.

Join the Z-Wave Network (Z-Stick)

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Z-Stick.
  3. If Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
  4. If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
  5. Press the Action Button on the Z-Stick to take it out of installation mode.

Join the Z-Wave Network (Minimote)

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Include button on your Minimote.
  3. If the Range Extender has been successfully linked to your Z-Wave network, its Network LED will no longer flash.
  4. If the linking was unsuccessful and the Network LED continues to flash repeat the above steps.
  5. Press any button on your Minimote to take it out of inclusion mode.

Exclusion from the Z-Wave Network (Z-Stick)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Z-Stick.
  4. If your Range Extender has been successfully removed from your network, its Network LED will flash.
  5. If the removal was unsuccessful, the Network LED will not flash.
  6. Press the Action Button on the Z-Stick to take it out of removal mode.

Exclusion from the Z-Wave Network (Minimote)

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Remove Button on your Minimote.
  4. If your Range Extender has been successfully removed from your network, its Network LED will flash.
  5. If the removal was unsuccessful, the Network LED will not flash.
  6. Press any button on your Minimote to take it out of removal mode.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Range Extender 6
ZW117
Repeater
Z-Wave Plus

Factory Reset

  1. Press and hold the Z-Wave Button for 20 seconds to completely factory reset your Range Extender 6.
  2. During the time that you are holding your Range Extender 6 action button down, the LED will flash through these colors: Yellow (at 2 seconds) > Purple (at 5 seconds) > Red for 8 seconds (initializing factory reset) > Green for 20 seconds (factory reset complete) > Rainbow LED (ready to be paired to a new gateway).
  3. You may let go when the LED turns green. Your Range Extender will now be reset to its original settings, and the green LED will be solid for 2 seconds and then remain the colorful gradient status as a confirmation.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Z-Wave Button on your Range Extender and quickly release the button (should only be a quick tap action on the button) and its LED will flash green rapidly (green indicates insecure pairing, if you want to pair securely, please refer to Enabling Security Encryption section in the Advanced Function section).
  3. If Range Extender has been successfully added  to your Z-Wave network, its LED will be solid for 2 seconds then turn off. If the adding was unsuccessful, the red LED will be on for 2 seconds and then remain colorful gradient status, repeat the steps above.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Z-Wave Button on your Range  Extender.
  4. If Range Extender has been successfully removed  from your network, its RGB LED will remain colorful gradient status.
  5. If the removal was unsuccessful, the RGB LED will still be solid, repeat the steps above.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Recessed Door Sensor Gen5
ZW089
Contact Sensor
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds and then release it. Your sensor will now be reset to its original settings

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Sensor. If your Sensor has been successfully linked to your network, its LED will become solid for 2 seconds then disappear.
  3. If linking was unsuccessful, the LED will continue to flash if you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Sensor. If your switch has been successfully unlinked to your network, its LED will begin to flash for a short time.
  4. If linking was unsuccessful, the LED will return to its last state. Tap the button to confirm if it has been unpaired, if unpaired successfully, the LED will flash when tapped.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Siren
ZW080
Siren
Z-Wave

Factory Reset

  1. Press and hold the Action button for 20 seconds
  2. At 8 seconds, the Siren will sound for 1 second, then stop
  3. The LED will continue to flash faster and faster and then will then turn solid for 2 seconds to indicate a successful factory reset
  4. You may let go of its Action button, and the Siren Gen5 factory reset is complete.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Siren Gen5, and its LED will flash rapidly to indicate that it is communicating.
  3. If your Siren has been successfully linked to your network, its LED will become solid for 2 seconds, then stop.
  4. If linking was unsuccessful, the LED will flash when you tap its button.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Siren.
  4. If your Siren has been successfully unlinked from your network, its LED will begin to flash.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Siren 6
ZW164-A
Siren
Z-Wave Plus

Factory Reset

  1. Press and hold the Action button for 20 seconds
  2. Within 2-5 seconds, the test siren sound will run, then stop after 5 seconds has elapsed.
  3. From 5-10 seconds, the LED will begin to flash faster and faster still from 10-20 seconds.
  4. After 21 seconds, the LED will quickly flash 3 times, and then the LED slowly pulse up and down as you hold down the Action Button.
  5. With the LED pulsing, release the Action button, and the Siren 6 will be reset to factory defaults.

Join the Z-Wave Network

  1. Power Siren 6 through the provided power adapter.
  2. Ensure that Siren 6 LED is flashing slowly.
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  4. Quickly tap the Siren 6 Action Button once.
  5. If Siren 6 has successfully joined your Z-Wave network, the LED will emit a solid color for 30 seconds, then turn off.
  6. If the Siren 6 failed to pair, the LED will continue to blink slowly.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button 6 times within 2 seconds .
  4. If your Siren 6 has been successfully excluded from the Z-Wave network, its LED will begin to flash slowly which indicates that it is ready to be paired again.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
Smart Switch 6
ZW096
Switch
Z-Wave Plus

Factory Reset

  1. Press and hold the Action Button for 20 seconds.
  2. The LED will change between these colors: Yellow > Purple > Red (flashs faster and faster) > Green (Successful indication of factory reset) > Rainbow LED (waiting to pair to new network).
  3. When the LED changes to Green state, you may let go of the action button.
  4. When the LED changes to a rainbow LED state, it will indicate that it is ready to pair to a new network.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your Switch once and the LED will flash a green LED.
  3. If your switch has been successfully linked to your network, its LED will become solid green for 2 seconds.
  4. If linking was unsuccessful, the LED will return to a rainbow gradient.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your Switch.
  4. If your switch has been successfully unlinked from your network, its LED will become a rainbow gradient.
  5. If linking was unsuccessful, the LED will become green or purple depending on how your LED mode is set.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
TriSensor
ZWA005
Motion Sensor
Z-Wave

Factory Reset

  1. Press and hold the Action Button for 15 seconds.
  2. The red LED flashes to confirm a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button on your sensor once.
  3. The LED will turn yellow LED for 10 seconds.
  4. If the LED flashes green twice, then the sensor has successfully joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your sensor.
  4. The LED will turn purple for 2 seconds, and then white when exclusion is successful.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
WallMote Quad
ZW129
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the Action button for 20 seconds.
  2. The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
  3. Let go of the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once on WallMote Quad to include it.
  3. The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your WallMote Quad.
  4. If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
  5. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.

Brand
Device
Product Number
Device Type
Protocol
Aeotec*
WallMote Quad
ZW130
Button Controller
Z-Wave

Factory Reset

  1. Press and hold the Action button for 20 seconds.
  2. The LED should flash between green, purple, then red which will flash rapidly until a green LED becomes solid for 2 seconds to indicate a successful factory reset.
  3. Let go of the Action Button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Action Button once on WallMote Quad to include it.
  3. The green LED will be on for 2 seconds and then the orange LED will fast flash for 10 minutes (if the WallMote Quad does not receive the Wake Up No More Info command from primary Controller) to indicate the inclusion is successful.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Action Button on your WallMote Quad.
  4. If your WallMote Quad is successfully removed from the Z-Wave network, the LED will become a colorful gradient for a few seconds and then turn off.
  5. If the removal was unsuccessful, the red LED will be solid for 2 seconds and then turn off, repeat the above steps.

August

Brand
Device
Product Number
Device Type
Protocol
August
Smart Lock Pro
ASL-03
Lock
Z-Wave

Factory Reset

  1. You must have your lock first connected to the August App
  2. Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device. Select Remove Z-Wave Device and on the next page you will see two options:
    • My Hub is in Exclusion Mode - use this mode when you have working hub and can properly disconnect.
    • My Hub is No Longer Working - use this mode to RESET the Device.
  3. Select the My Hub is No Longer Working option and then select Reset Z-Wave Device.

Join the Z-Wave Network

  1. You must have your lock first connected to the August App
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. On the August App, go into Lock Settings and door for Z-Wave Settings.
  4. The first time the screen will state that "The Lock is not connected to a Z-Wave Network". Select "Add to a Z-Wave Network".
  5. Follow the instructions to put the lock into Learn Mode.

Exclusion from the Z-Wave Network

  1. You must have your lock first connected to the August App
  2. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  3. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  4. Go into Lock Settings > Z-Wave Settings. If you are connected, you will see Remove Z-Wave Device.
  5. Select Remove Z-Wave Device and on the next page you will see two options.
    • My Hub is in Exclusion Mode - Use this mode when you have a working hub and can properly disconnect.
    • My Hub is No Longer Working - Use this mode to RESET the Device.
  6. Select the My Hub is in Exclusion Mode option to exclude the lock from the Z-Wave network.

BeSense

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave PLUS Ceiling PIR Sensor
IX32
Motion Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave Plus Window/Door Sensor
IM20
Contact Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

Brand
Device
Product Number
Device Type
Protocol
BeSense
Zwave PIR Sensor
IX30
Motion Sensor
Z-Wave

Factory Reset

  1. Press the tamper switch for 6 times to restore factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Activate the inclusion mode at the sensor by pressing the tamper switch 3 times.
  3. Wait about 15-30 seconds while the sensor and hub finish the inclusion process.

Exclusion from the Z-Wave Network

  1. From the Hubitat Web Interface, go to the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the tamper switch 3 times and the sensor will be removed from the Z-Wave network after 15-30 seconds.

BOSCH

Brand
Device
Product Number
Device Type
Protocol
BOSCH
PIR Motion Detector
ISW-ZPR1-WP13
Motion Detector
Zigbee

Factory Reset

  1. Unlock the battery cover and slide it upwards to remove.
  2. Press upward on the tamper switch located in-between the batteries, keeping it engaged while you remove both batteries.
  3. Wait at least 4 seconds, but do not release the tamper switch.
  4. Keep the tamper switch engaged while you reinsert both batteries.
  5. Release the tamper switch. The device is now reset to factory default settings.

Join the Zigbee Network

  1. Unlock the battery cover and slide it upwards to remove.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  3. Remove both batteries for at least 10 seconds.
  4. Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds
  5. The LED will begin to blink On > Off > On > Off > On > Off (for 5 seconds) and will continue to blink in this cycle for up to 3 minutes
  6. If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
Brand
Device
Product Number
Device Type
Protocol
BOSCH
PIR Motion Detector
ISW-ZDL1-WP11G
Motion Detector
Zigbee

Factory Reset

  1. Unlock the battery cover and slide it upwards to remove.
  2. Press upward on the tamper switch located in-between the batteries, keeping it engaged while you remove both batteries.
  3. Wait at least 4 seconds, but do not release the tamper switch.
  4. Keep the tamper switch engaged while you reinsert both batteries.
  5. Release the tamper switch. The device is now reset to factory default settings.

Join the Zigbee Network

  1. Unlock the battery cover and slide it upwards to remove.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Pairing on the Device Discovery page.
    • See Discovering your devices for detail instructions.
  3. Remove both batteries for at least 10 seconds.
  4. Reinsert both batteries. The LED on the front of the sensor will be solid for 2 seconds
  5. The LED will begin to blink On > Off > On > Off > On > Off (for 5 seconds) and will continue to blink in this cycle for up to 3 minutes
  6. If the motion sensor does not pair with the hub in less than 3 minutes, perform a factory reset and repeat the above steps to join the Zigbee network.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Centralite

Brand
Device
Product Number
Device Type
Protocol
Centralite
Pearl Thermostat
3000-G
Thermostat
Zigbee

Factory Reset

  1. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  2. The device will then factory reset itself and begin looking for an open network to join.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Enter Programming Mode, navigate to Menu ID “17”, press HOLD, then navigate to option “11”, then press HOLD again.
  3. The device will then factory reset itself and begin looking for an open network to join.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Smart Outlet
3200-G
Outlet
Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Door & Window Sensor
3300-G
Contact Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor off the mount, remove cover, and remove battery.
  3. While holding down the reset button, reinsert battery to factory reset the device.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Motion Sensor
3305-G
Motion Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor off the mount, remove cover, and remove battery.
  3. While holding down the reset button, reinsert battery to factory reset the device.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Micro Door Sensor
3323-G
Contact Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor off the mount, remove cover, and remove battery.
  3. While holding down the reset button, reinsert battery to factory reset the device.

Brand
Device
Product Number
Device Type
Protocol
Centralite
3-Series Micro Motion Sensor
3328-G
Motion Sensor
Zigbee

Factory Reset

  1. Slide the sensor off the mount, remove cover, and remove battery.
  2. While holding down the reset button, reinsert battery to factory reset the device.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Slide the sensor off the mount and remove cover. Remove battery for 10 seconds and replace

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Slide the sensor off the mount, remove cover, and remove battery.
  3. While holding down the reset button, reinsert battery to factory reset the device.

Brand
Device
Product Number
Device Type
Protocol
Centralite
4-Series Smart Outlet
4200-C
Outlet
Zigbee

Factory Reset

  1. Unplug any devices from the module and unplug from the wall.
  2. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Unplug any devices from the module and unplug from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.
  4. After the Smart Outlet has successfully joined a ZigBee network, the status LED will turn solid green

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.
  2. Unplug any devices from the module and unplug from the wall.
  3. Hold the on/off button while plugging it back into the wall and continue to hold the button until the status LED turns on.

CREE

Brand
Device
Device Type
Protocol
CREE
Connected LED Bulbs
Bulb
Zigbee

Factory Reset

  1. Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
  2. The bulb will flash once, indicating it is reset and ready for pairing

Factory Reset (Alternate Method)

  • Method 1 - Use a Philips Hue Dimmer Switch
  1. Turn the bulb on (ensure there are no others in the same lamp, as they could be reset too, using this method).
  2. Hold the remote within 4 inches of the bulb.
  3. Press and hold the 1st (On / I in some countries) and the 4th (Off / O in some countries) buttons simultaneously for about 10 seconds, until the bulb starts flashing on and off.
  4. If the bulb stopped flashing (it will normally turn fully on again after reset) and the green LED on the remote (top left of the remote) flashed green - your bulb is reset.
    • This method can be used for nearly ALL ZigBee LL bulbs.
  • Method 2 - Use a Lutron LZL-4B Connected Bulb Remote (Discontinued Product)
  1. Hold the remote within 4 inches of the bulb.
  2. Press and hold the 2nd (up arrow) and 4th (light off) buttons simultaneously.
  3. The bulb should flash on and off
  4. The green LED on the remote should come on and may flash a few times.
  5. Continue to hold both buttons on the remote until the green LED goes off completely.
    • This method can be used for nearly ALL ZigBee LL bulbs.

Join the Zigbee Network

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb > pause 2 seconds > turn OFF the bulb > pause 2 seconds > Turn ON the bulb
  3. The bulb will flash once, indicating it is reset and ready for pairing

Join the Zigbee Network (Alternate Method)

  1. From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
  2. See Factory Reset (Alternate Method) above to reset the bulb and put it into pairing mode.

Leaving the Zigbee Network

  1. From the device's details page, select Remove Device, then Remove.

Dome

Brand
Device
Product Number
Device Type
Protocol
Dome
Door / Window Sensor
DMWD1
Contact Sensor
Z-Wave

Factory Reset

  1. Open the Cover and make sure the Door/Window Sensor is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator flashes once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the Cover of the Door/Window Sensor.
  3. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the Cover of the Door/Window Sensor.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Door / Window Sensor
DMDP1
Contact Sensor
Z-Wave

Factory Reset

  1. Remove the Sensor Cover and confirm that your Door/Window Sensor is powered up.
  2. Wait for 5 seconds.
  3. Move the Magnet and Sensor Base in and out of the closed position 6 times.
  4. The LED indicator will light up Red for 5 seconds when reset successfully. The Door/Window Sensor’s memory will be erased to factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the Sensor Cover and the LED indicator will start flashing yellow.
  3. Press the Button quickly 3 times in a row.
  4. The device will enter inclusion mode for two minutes and the LED indicator will alternate between green and red. After successful inclusion, the LED Indicator will flash green 3 times then flash red until the cover is replaced.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the SENSOR COVER and the LED indicator will start flashing red.
  4. Press the Button quickly 3 times in a row.
  5. The LED Indicator will flash green 3 times indicating successful exclusion from the Z-Wave network. It will continue flashing red (indicating tamper) until the cover is replaced.

Brand
Device
Product Number
Device Type
Protocol
Dome
Leak Sensor
DMWS1
Water Sensor
Z-Wave

Factory Reset

  1. Open the Back Plate and make sure the Leak Sensor is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator flashs once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the cover of the Leak Sensor by twisting it apart.
  3. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the cover of the Leak Sensor by twisting it apart.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Leak Sensor
DMMS1
Water Sensor
Z-Wave

Factory Reset

  1. Remove the Cover and make sure the Motion Detector is powered.
  2. Hold the Connect Button for 10 seconds until the LED indicator flashes once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the cover of the Motion Detector by twisting it apart.
  3. Press the Connect Button quickly 3 times in a row.
  4. The LED indicator will flash 5 times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the cover of the Motion Detector by twisting it apart and make sure the Motion Detector is powered.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Mouser
DMMZ1
Mouse Trap
Z-Wave

Factory Reset

  1. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  2. Press and hold the CONNECT BUTTON for at least 10 seconds then release.
  3. A flashing LED indicator indicates a successful factory reset. The Mousers memory will be erased to factory settings.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  3. Press the CONNECT BUTTON quickly 3 times in a row.
  4. The LED indicator will flash 5 times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the TOP COVER by sliding it back and lifting up. Confirm that your Mouser is powered up.
  4. Press the CONNECT BUTTON quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
On/Off Plug-In Switch
DMOF1
Switch
Z-Wave

Factory Reset

  1. Plug in the On/Off Plug-In Switch.
  2. Hold the Connect Button for 10 seconds until the LED Indicator flashes once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the On/Off Plug-In Switch within range of your Z-Wave Controller.
  4. Press the Connect Button quickly 3 times in a row. The LED indicator will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Range Extender
DMEX1
Repeater
Z-Wave

Factory Reset

  1. Hold the Button for 10 seconds until the LED flashes 10 times, then release the button

Join the Z-Wave Network

  1. For proper inclusion, install the Range Extender in the final location where it will be used.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Plug the Range Extender into an outlet or use a micro USB (not included) to power it. The LED will flash 5 times indicating successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the Button quickly 3 times in a row The LED will flash 5 times indicating successful exclusion.

Brand
Device
Product Number
Device Type
Protocol
Dome
Siren
DMS01
Siren
Z-Wave

Factory Reset

  1. Open the Back Plate and make sure the Siren is powered.
  2. Hold the Connect Button for 10 seconds until the LED Ring flashs once, then release the button.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the Back Plate of the Siren.
  3. Press the Connect Button quickly 3 times in a row. The LED Ring will flash 5 times indicating successful inclusion to the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the Back Plate of the Siren.
  4. Press the Connect Button quickly 3 times in a row. The LED Ring will flash 5 times indicating successful exclusion from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Dome
Water Main Shut-Off
DMWV1
Shutoff Valve
Z-Wave

Factory Reset

  1. Press and hold the open/close button for at least 10 seconds then release.
  2. The Shut-Off’s memory will be erased to factory settings. A flashing light indicates a successful factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Make sure the Water Main Shut-Off is powered on, then press the “open/close” button quickly 3 times in a row. The LED will stop flashing and stay on continuously upon successful inclusion.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. When prompted, press the “open/close” button on the Shut-Off quickly 3 times in a row.

Dragon Tech

Brand
Device
Product Number
Device Type
Protocol
Dragon Tech
Plug in Z-Wave Plus Dimmer Switch
PD-100
Dimmer
Z-Wave

Factory Reset

  1. Unplug the PD-100 and anything the is plugged into it.
  2. Press and hold the button on the front of the PD-100
  3. Plug the PD-100 in while still pressing the button
  4. After 3 seconds, release the button. If the button flashes, the PD-100 has been successfully reset. If not, repeat the steps to factory reset.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the button on the front of the PD-100

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the button on the front of the PD-100

Eaton (Cooper Wiring Devices)

Brand
Device
Product Number
Device Type
Protocol
Eaton
Wireless Dimmer
RF9540
Dimmer
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.

Join the Z-Wave Network

  1. Cooper Wiring Devices Z-Wave device has a blue LED, which will flash when the device is not included in a Z-Wave network. The LED stops flashing when the device is in a network.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  3. Press the device switch once to include it in the network. The LED will stop flashing, indicating the dimmer has been successfully included in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the device switch once to exclude it from the network. The LED will start flashing, indicating the dimmer has been successfully excluded from the Z-Wave network.

Ecolink

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Door / Window Sensor
DWZWAVE2.5-ECO
Contact Sensor
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. When the inclusion process is complete, the LED on the sensor will be solid blue, then go out.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. When the exclusion process is complete, the LED on the sensor will be solid blue, then go out.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Flood/Freeze Sensor
FLF-ZWAVE5
Water Sensor
Z-Wave Plus

Factory Reset

  1. The Flood Freeze sensor factory defaults on network exclusion
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for 1 second, then reinstall it.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the battery for at least 10 seconds, then reinstall it.
  3. If the LED starts flashing continuously, the sensor has no node ID and was not successfully added, so start from step 1 again. Make sure to remove the battery for 10 seconds if adding to a Z-Wave network fails.
  4. If after 5 seconds the LED is not flashing, look on Hubitat Elevation™ for feedback on whether the sensor was added successfully. If you do not see any feedback that the sensor was added, follow directions for exclusion of the sensor from a Z-Wave network, and then try adding the sensor again. If you are still having problems, you may need to add Z-Wave repeaters in-between the controller and the sensor.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the Flood Freeze case and remove the battery for 1 second.
  4. Replace the battery and the device should be removed from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Motion Sensor with Pet Immunity
PIR-ZWAVE2.5
Motion Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Siren
SC-ZWAVE5
Siren
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  4. The LED on the front of the unit will turn off if successful exclusion from the network.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Plug in the Z-Wave Plus Siren and verify a single beep sound is heard.
  4. The LED on the front of the unit will turn off if successful exclusion from the network.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
FireFighter
FF-ZWAVE5
Smoke/CO Detector
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the FireFighter case and press the learn button on the device for 1 second.
  4. If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Open the FireFighter case and press the learn button on the device for 1 second.
  3. If the LED starts flashing continually, the sensor has not been added. Repeat the steps.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Open the FireFighter case and press the learn button on the device for 1 second.
  4. If successfully removed from the Z-Wave Plus network, the devices Green LED should flash slowly continuously

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch
DLS-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successfully included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch Double Toggle
DTLS2-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Smart Switch Dual Rocker
DDLS2-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Tilt Sensor
TILT-ZWAVE2
Tilt Sensor
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Tilt Sensor
TILT-ZWAVE2.5
Tilt Sensor
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Remove the battery for at least 5 seconds, then reinstall it.
  3. Re-attach the battery cover and the device with enter inclusion mode
  4. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the inclusion process.
  5. Test the sensor before mounting it permanently. The sensor LED will flash each time the sensor position is changed. Check Hubitat Elevation™ device details status to observe changes.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Remove the battery for at least 5 seconds, then reinstall it.
  4. Re-attach the battery cover and the device with enter exclusion mode
  5. The LED will flash for 10 seconds and the go out. If the sensor LED continues to flash, repeat the exclusion process from step 2.

Brand
Device
Product Number
Device Type
Protocol
Ecolink
Toggle Light Switch
TLS-ZWAVE5
Switch
Z-Wave Plus

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the inclusion / exclusion button on the Smart Switch.
  3. The LED on the front of the unit will turn off if successful included in the network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion / exclusion button on the Smart Switch.

Enerwave

Brand
Device
Product Number
Device Type
Protocol
Enerwave
Ceiling Mounted PIR Motion Sensor
ZWN-BPC-Plus
Motion Sensor
Z-Wave Plus

Factory Reset

  1. To reset the ZWN-BDC-PLUS, simply press the exclusion button on the sensor 3 times and hold for 3 seconds on the 3rd press.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the inclusion/exclusion button on the sensor 3 times.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the inclusion/exclusion button on the sensor 3 times.

Everspring

Brand
Device
Product Number
Device Type
Protocol
Everspring
Door/Window Detector
HSM02
Contact Sensor
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED will be steady on.
  2. Within 1 second, press and hold the tamper switch until LED is off.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second will enter exclusion mode. The LED will light up once, each time the tamper switch is pressed.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Flood Detector
ST812
Water Sensor
Z-Wave

Factory Reset

  1. Press link key three times within 1.5 second. The sensor will beep each time the link key is pressed.
  2. Within 1 second, press and hold the link key. The sensor will long beep for 5 seconds. Keep holding the link key until the long beep stops.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Pressing link key three times within 1.5 second and the sensor will enter inclusion mode. The sensor will beep once, each time the link key is pressed.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing link key three times within 1.5 second will enter exclusion mode. The sensor will beep once, each time the link key is pressed.

Brand
Device
Product Number
Device Type
Protocol
Everspring
PIR Detector
HSP02
Motion Sensor
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED will be steady on.
  2. Within 1 second, press and hold the tamper switch until LED is off.
  3. The LED will cycle on for 2 seconds and off for 2 seconds indicating the sensor has been reset for factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second will enter exclusion mode.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Photoelectric Smoke Alarm
SF-813
Smoke Detector
Z-Wave

Factory Reset

  1. Press tamper switch three times within 1.5 second. The LED flashes and the buzzer sounds when the link key is pressed.
  2. Within 1 second, press and hold the tamper switch for 5 seconds until the LED is off.
  3. The LED will light for 5 seconds and the buzzer will sound for 5 seconds

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Pressing tamper switch three times within 1.5 second and the sensor will enter inclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
  3. The detector will stay awake and remain in inclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
  4. The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has joined the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing tamper switch three times within 1.5 second and the sensor will enter exclusion mode. The LED flashes and the buzzer sounds when the link key is pressed.
  4. The detector will stay awake and remain in exclusion mode for 10 minutes, or until the device has successfully joined the Z-Wave network.,
  5. The LED will light for 1 second and the buzzer will sound for 1 second to indicated the detector has been excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Everspring
Temperature/Humidity Detector
SF-814
Temperature Sensor
Z-Wave

Factory Reset

  1. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
  2. Within 1 second, press the temperature unit/linking key again, and the sensor will emit a long beep. Keep holding the temperature unit/linking key until the long beep stops.
  3. When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks and has been reset to factory defaults.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Pressing the temperature unit/linking key 3 times within 1.5 seconds will enter inclusion mode. The linking signal symbol will flash on the display.
  4. When the radio frequency status shows no signal, the device has been excluded from any previously joined Z-Wave networks

Evolve

Brand
Device
Product Number
Device Type
Protocol
Evolve
Isolated Contact Fixture Module
LFM-20
Relay
Z-Wave

Factory Reset

  1. Factory reset is unavailable for this device. Instead, perform a general exclusion.
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Exclude the module by tapping the button 3 times, then press and hold for 10 seconds.
    • LFM-20 release 5.41 requires that you tap 2 times, then press and hold for 10 seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the button on the device once to include it in the Z-Wave network.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Exclude the module by tapping the button 3 times, then press and hold for 10 seconds.
    • LFM-20 release 5.41 requires that you tap 2 times, then press and hold for 10 seconds.

Fibaro

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Button
FGPB-101
Outlet
Z-Wave

Factory Reset

  1. Click the Button exactly five times.
  2. Press and hold the Button for at least 5 seconds.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Click the button at least 6 times.
  3. Wait for the device to be added into the system, successful inclusion will be confirmed by Hubitat Elevation™
  4. Click the button 4 times to wake it up
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Click the Button at least 6 times.
  4. Wait for the removing process to end.
  5. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Door/Window Sensor 2
FGDW-002
Contact Sensor
Z-Wave

Factory Reset

  1. Open the cover and remove the battery.
  2. Install the battery while holding both TMP buttons.
  3. The LED indicator will be flashing slowly for 5 seconds, but keep holding the buttons.
  4. Release one button when the LED indicator starts flashing quickly.
  5. Click the released button once to confirm initiation of the reset procedure.
  6. Wait a few seconds for a long flash of the LED indicator. Do not remove the battery.
  7. The LED indicator will flash 5 times quickly to confirm reset of the device.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press one of the TMP buttons quickly, 3 times in a row, while keeping other button is pressed.
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press one of the TMP buttons quickly, 3 times in a row, while keeping other button is pressed.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Flood Sensor
FGFS-101 FG3
Water Sensor
Z-Wave

Factory Reset

  1. Make sure the sensor is powered.
  2. Press and hold the TMP button.
  3. Wait for the visual LED indicator to glow yellow (4th position of the MENU).
  4. Release the TMP button.
  5. Click the TMP button once to confirm selection.
  6. After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Removed the battery for 10 seconds, and re-install it
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the TMP button quickly, 3 times in a row.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
Flood Sensor ZW5
FGFS-101 ZW5
Water Sensor
Z-Wave Plus

Factory Reset

  1. Make sure the sensor is powered.
  2. Press and hold the TMP button.
  3. Wait for the visual LED indicator to glow yellow (4th position of the MENU).
  4. Release the TMP button.
  5. Click the TMP button once to confirm selection.
  6. After few seconds the device will restart with factory settings, which is signaled with the red visual indicator color and an acoustic signal.

Join the Z-Wave Network

  1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
  2. Press the TMP button quickly, 3 times in a row.
  3. Wait for the inclusion process to end.
  4. Successful inclusion will be confirmed by Hubitat Elevation™
  5. Watch the status in the device details page to confirm proper operation.

Exclusion from the Z-Wave Network

  1. From the device's details page, select Remove Device, then Remove
  2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
  3. Press the TMP button quickly, 3 times in a row.
  4. The device will be excluded from the Z-Wave network.

Brand
Device
Product Number
Device Type
Protocol
Fibaro
KeyFob
FGKF-601 ZW5
Button Controller
Z-Wave Plus

Factory Reset

  1. Click O and simultaneously.
  2. Click or X until LED is Yellow - reset the device.
  3. Click + to confirm selection, or is you do not wish to reset at this time, click to exit the menu.
  4. The LED will pulse Yellow twice to confirm the device has been reset.<